Speakman S-3552 Instructions / Assembly
Contents
1. Instructions For Models S 3962 LD S 3552 need help For additional assistance or service call Speakman Company 400 Anchor Mill Road New Castle DE 19720 Phone 800 537 2107 Fax 800 977 2747 Email customerservice speakmancompany com Web Site www speakmancompany com 92 2809 what you need to know Tools Adjustable Wrench Pliers Pipe Wrench Screwdriver Teflon Tape Maintenance Your new lavatory faucet is designed for years of trouble free performance Keep it looking new by cleaning it periodically with a soft cloth Avoid abrasive cleaners steel wool and harsh chemicals as these will dull the finish and void your warranty Safety Tips If you use soldering for the installation of the faucet the seats cartridges and washers will have to be removed before using flame Otherwise warranty will be void on these parts Protect your eyes with safety glasses when cutting or soldering water supply line Cover your drain to avoid loosing parts Important points Prior to beginning installation turn off the cold and hot water lines and open the old faucet to release build up pressure When installing your new faucet turn the connector nuts finger tight then use one wrench to anchor the fitting and a second wrench to tighten the nut one additional turn Connections that are too tight will reduce the integrity of the system Wrap all threaded connections with Teflon tape available at2. p coupling nut behind ball nose of flexible supply tube Ball nose coupling will go partially into IPS shank or fitting Tighten coupling nut DO NOT OVER TIGHTEN Install opposite end according to manufacturer s instructions for both tubes Important After installation is completed remove aerator Turn on water supply and allow both hot and cold water to run for at least one minute each Replace aerator Remove stopper 1 and flange 2 and rubber washer 3 Screw nut 4 all the way down Push gasket 5 down Insert body 2 into sink Screw flange 1 onto body Pivot hole 3 must face back of sink Tighten nut gasket 4 Remove pivot nut 1 Install horizontal rod 2 and stopper 3 as removable 4 or non removable 5 Hand tighten pivot nut 1 Attach horizontal rod to strap 6 using clip 7 D Insert lift rod 1 through faucet and into strap 2 Tighten screw 3 Connect assembly to drain 4 Trouble shooting PROBLEM Leaks underneath handle CAUSE Bonnet has come loose or Rubber valve seat is dirty or worn ACTION 1 Remove handle by loosening set screw with Allen wrench Diagram A Unscrew the cap assembly 2 Tighten the bonnet by turning it clockwise Diagram B Move the cartridge stem to the on position The leak should stop draining out from around the cartridge stem 3 If the leak does not stop shut off the water supply Remove the bonnet b
3. s 3 Re install the small parts as shown in the exploded diagram Diagram H Metal screens must be flat and plastic supporter must be straight 4 Screw the aerator onto the spout end and tighten RPG05 0800 N oO Q i lt o A a S RPG01 0055 _ RPG05 0822
4. y turning it counter clockwise remove cartridge Diagram C Inspect the small rubber valve seats for debris and replace with new valve seats if necessary Diagram D 4 Position the cartridge back to the faucet body Diagram E Re tighten the Bonnet and cap Diagram F Replace the handle and tighten the set screw PROBLEM Water does not completely shut off CAUSE Rubber valve seat is dirty or worn ACTION Remove handle by loosening set screw with Allen wrench Diagram A 2 Turn off the water under the sink 3 Unscrew the cap and bonnet assembly then remove cartridge Diagram C 4 Inspect the small rubber valve seats for debris and replace with new valve seats if necessary Diagram D 5 Position the cartridge back to the faucet body Diagram E 6 Re tighten the Bonnet and cap Diagram F Replace the handle and tighten the set screw 7 Turn on the water under the sink PROBLEM Faucet leaks around aerator CAUSE Aerator incorrectly fitted ACTION 1 Unscrew the aerator by turning it clockwise Diagram G Inspect the black rubber packing inside the aerator The rubber packing should be flat 2 Screw the aerator onto the spout end and tighten PROBLEM Improper water pattern CAUSE Aerator dirty or small parts inside aerator improperly installed ACTION 1 Remove the aerator from the spout end by turning it clockwise 2 Gently flush the small parts inside the aerator to clear away any debri
5. your local hardware or plumbing supply store Always wrap in a clock wise direction Things You May Need All installations can vary depending on how your previous faucet was installed Necessary supplies to install your faucet are not all included however they are available wherever plumbing supplies are sold When choosing your installation supplies make sure they are IAPMO and or CSA approved products Shut off water supply Remove old faucet Clean sink surface in preparation for new faucet RS i Screw metal threaded rods two rods included upwards into body of faucet Use cross slots in body of faucet for screw driver Place new faucet through holes in top of sink From underside slide large washers onto threaded rods making sure open slots are around copper tubes Line up faucet with edge of sink Tighten nuts A Stainless Steel Braided Faucet Supply Tubes This is the simplest of all installations If you are using stainless steel braided faucet supply tubes this faucet requires one end of the supply tube to have a 1 2 female IPS connection The other end of this supply tube must match the thread on the water supply fittings or shut off valve under your sink Once you have identified the required tube carefully follow the manufacturer s installations instructions for each tube B Ball Nose Flexible Supplies If you are using ball nose flexible supplies to connect the faucet to water supply lines Sli
Download Pdf Manuals
Related Search