Basco 100-6RNOR Installation Guide
Contents
1. 100 200 PARTS LIST 1 Curb J 3 8 x 2 Truss Head Screws Jamb Wiper Vinyl K 10 x 7 16 Sq Hd Set Screws Pivot Jamb L Glazed Door Panel Pivot Brackets M Nylon Pivot Bushing Strike Jamb Magnetic 8 x 1 Flat Head Screws Interior Handle Exterior Handle 8 x 1 8 Allen Set Screws P Allen Wrench 5 64 R 1 1 2 5 6 x 3 8 Truss Head Screws N 2 1 6 Plastic Wall Anchors S WR Nee N QCI0001 Rev 0 Page 3 of 7 p PS PS e S 2 6x 1 1 4 Round Head Drip Rail Tapered Drip Vinyl 2 Drip Plugs Roll Drip Tape Certified 11 10 2006 The Basco 100 200 Pivot Shower Door is completely reversible and may be installed pivot right or pivot left Using the diagram determine the correct position for your installation For maximum waterproofing the pivot jamb should always be opposite the shower head These instructions depict a pivot left installation CAUTION For safety the door must always open PIVOT LEFT PIVOT RIGHT outward 2 Note The 100 200 unit may be installed without using the sloped curb A provided Its use is definitely recommended for positive water control on shower sills with little or no slope Measure the wall to wall opening at the shower sill and cut the curb to the exact length File the ends of curb as necessary to fit the corner contours of the enclosure Place the curb on the shower sill with the RAISED portion to the exterior of the enclosure Make sure the2. curb is centered on the sill and lightly mark its position on the sill with a pencil Remove the curb from the sill CURB 3 Run two beads of caulk inside the penciled marks on the shower sill Place the curb A in the exact position CURB marked in Step 2 and seat it firmly in the caulking Also caulk the ends of the curb to the walls Hold curb into place with masking tape gt NOTE Improper caulking will result in leaks QCI0001 Rev 0 Page 4 of 7 Certified 11 10 2006 4 Slide the jamb wiper vinyl B into the pivot jamb C A small amount of soapy water will help installation Cut the jamb wiper vinyl 7 8 shorter than the pivot jamb to allow room for the pivot brackets D Fit one of the pivot brackets into the bottom of the pivot jamb Lock it in place with a 6 x 3 8 truss head screw E and a 8 32 x 1 8 set screw F a 5 64 Allen wrench G is provided NOTE Set screws F are pre installed 9 Place the pivot jamb C on the curb A with the exterior face lined up with the raised edge of the curb Use a level to plumb the jamb then mark the mounting hole locations Remove the jamb and drill the mounting holes For tile or marble walls drill three 7 32 diameter holes and insert the plastic wall anchors H A center hole punch helps locate the holes accurately Attachments to fiberglass or acrylic units can be made in two ways If reinforcement 1s built into the wall of the unit drill three 1 8
3. INSTALLATION INSTRUCTIONS REEL eorom M SHOWER ENCLOSURES Unit No 100 200 500 Pivot oingle Swing Shower Enclosure Lj LAE m n iis lias LIUM MA ery MILL eL E pa Ti a Ret tue Zen eg am i Lir na 4g Jr at AA hik Y 1 i L 5 mu Li QCIO0001 Rev 0 Page 1 of 7 Certified 11 10 2006 MAINTENANCE Two primary materials are used to manufacture your new Basco enclosure tempered glass and anodized aluminum To assure a long lasting finish on the enclosure wipe it down with a towel after each use Never use a scouring agent to clean the aluminum For occasional more concentrated cleaning efforts we find that Maintain AquaGlideXP Spray Cleaner helps minimize water stains and oxidation Maintain is not only extremely effective at enhancing the long term performance of glass coated with AquaGlideXP it can aid in cleaning untreated glass as well Ask your distributor about Maintain Spray or visit www bascoshowerdoor com warranty and care care and cleaning aspx to purchase online Many over the counter cleaners if applied to aluminum and left on will harm the metal finish and cause permanent damage even though their directions indicate safe use on shower doors Be sure that any over spray falling on the aluminum frame is rinsed thoroughly and dried INSTALLATION NOTES Unpack your unit carefully and inspect for freight damage Lay out and identify all parts using the instruction sh
4. diameter holes to install mounting screws directly into the reinforcement If walls are not reinforced drill 7 32 holes and install plastic wall anchors or Molly bolts Molly bolts are not supplied by BASCO Replace the pivot jamb and attach to the wall with three 8 x 2 truss head screws J 6 Thread the two 10 24 x 7 16 square head set screws K into the tapped holes in pivot blocks in the top and bottom rails of the glazed door panel L Measure the distance from the wall to wall directly above the curb Dim A Deduct 3 13 16 from this amount and position the pivot pins this exact distance Dim B from the edge of the door Tighten the set screws just enough to prevent the pivot blocks from moving finger tight plus a quarter turn A 3 16 wrench not supplied by BASCO will fit the set screw mud SET SCREW QCI0001 Rev 0 Page 5 of 7 Certified 11 10 2006 Insert a nylon pivot bushing M into the bottom pivot bracket D Slip the second pivot bushing over the top pivot pin on the door panel Position the door by inserting the bottom pivot pin into the bottom pivot bracket Hold the door vertical and slide the top pivot bracket into the pivot bushing Secure the top pivot bracket with a 6 x 3 8 truss head screw E and a 8 32 x 1 8 Allen set screw F 8 Your Pivot Door is equipped with a magnetic catch Attach the strike jamb N to the door Close the door so the strike jamb is 7 8 from the fr
5. eets as a reference Before discarding the carton check to see that no small hardware parts have fallen to the bottom of the box If any parts are damaged or missing refer to the descriptions noted in the instructions when contacting your dealer for replacements Handle the glass panels carefully and protect the edges Safety tempered glass is very resistant to breakage but the sharp corners of the panels can damage tile and floor surfaces Please wear safety glasses whenever drilling or cutting When drilling holes in the ceramic tile or marble use a center punch and hammer to carefully break the surface glaze so the drill can start without skidding To install your BASCO Shower Door you will need the following tape measure level 2 Phillips screwdriver 3 16 wrench drill 1 8 and 3 16 drill bits hacksaw pencil and caulking clear silicone recommended Optional tools include a miter box for cutting parts to length files center punch and masking tape For drilling tile a 3 16 masonary bit is recommened NOTE Tempered glass cannot be cut Although safety tempered glass is very resistant to breakage the glass can still break if unequal pressure is placed on it during installation Use caution In addition the sharp corners of the panels can damage tile and floor surfaces so it is best to handle the glass panels carefully and protect the edges QCIO001 Rev 0 Page 2 of 7 Certified 11 10 2006 Crews TOM MOODY gt
6. ick tape Y and carefully apply it to the back of the drip rail do not peel the tape backing yet Insert the tapered drip vinyl W into the drip rail Position the drip rail flush with the bottom and pivot side of the door panel L then raise the strike side until the bottom edge of the drip vinyl is parallel to the curb A Mark the location of each end of the drip rail 11 Adjust the drip vinyl W by sliding it left or right until it just touches the curb Trim the vinyl flush DRIP RAIL I n with the pivot end and notch 1 4 longer than the drip DRIP i im rail as shown on the strike end Secure it with one 6 x PLUG Eg 3 8 truss head screw E in the pivot end of the drip DAP dec Eg VINYL rail The drip plug X is supplied with a left and right hand plug together Break the right and left drip plug apart and insert the appropriate plug into the high strike side of the drip rail Discard the unused drip plug Peel off the tape backing and carefully press the drip rail to the door in the marked position NOTE Cleaners with alcohol content can dissolve the adhesive that attaches the drip rail To prevent Only Use One this possibility place a small bead of clear sealant at Plug On Strike the top of the drip rail where it is attached to the sic da Side nly bottom rail 12 Neatly caulk the inside perimeter of the shower curb and wall jambs NOTE The caulking should be allowed to cure for twenty fo
7. ont of the curb A and mark the jamb location on the wall If the curb is not used close the door parallel to the shower sill and mark the jamb location Remove the strike jamb from the door hold it in the marked location and mark the hole locations for the mounting screws Drill the mounting holes per the instructions in Step 5 Replace the strike jamb and attach it to the wall with three 8 x 1 1 2 flat head screws P Close the door and check the clearance with the strike jamb If necessary loosen the set screws K on the top amp bottom slide bars and adjust the door panel to align the magnets When the door panel is properly aligned tighten the set screws securely 9 Attach the interior door handle R and the exterior door handle S to the door with two 26 32 x 1 1 4 round head screws T QCI0001 Rev 0 T KB x 1 8 xX GET SCHEW SCREW p PIVOT BUSHING PIVOT BRACKET 7 PIVOT JAMB IDENTIFICATION INTERIOR GROOVES MAGNETIC HANDLE LATCH 48 X 11 2 SCREW aN STRIKE SEE JAMB fiais H ene STRIKE RAIL Om mem EXTERIOR HANDLE Be DOOR b PANEL 28x11 SCREWS EXTERIOR HANDLE INTERIOR HANDLE Page 6 of 7 Certified 11 10 2006 1 0 Clean the bottom door rail and the drip rail thoroughly with rubbing alcohol to ensure proper adhesion Unroll the double st
8. ur hours before using your new shower enclosure QCI0001 Rev 0 Page 7 of 7 Certified 11 10 2006
Download Pdf Manuals
Related Search