Home Decorators Collection 1759400410 Instructions / Assembly
Contents
1. HOME DECORATORS COLLECTION HDC 17594 MFG TW 19151WO TW 19151DW MANOR LINEN STORAGE CABINET 69 Hx19 Wx14 D ASSEMBLY INSTRUCTIONS Note 1 Before assembly please be sure to work on a soft flat surface to avoid any damage to the finish 2 You need at least 2 people to finish the assembly of this product Made In China on E S m P 1 10 BEFORE ASSEMBLY IMPORTANT NOTE READ CAREFULLY BEFORE ASSEMBLY TO PREVENT DAMAGE TO PARTS FOLLOWING INSTRUCTIONS LISTED BELOW IN THE PROPER SEQUENCE AS NUMBERED TO ASSURE FAST EASY AND CORRECT ASSEMBLY ASSEMBLY TOOLS REQUIRED BP L Screw driver Rubber Mallet Electric drill WOODEN DOWEL INSTALLATION PROCEDURE 1 FILL HOLE 1 4 FULL OF GLUE m 2 GENTLY TAP DOWEL INTO HOLE WITH RUBBER MALLET OR USE HAND PRESS TIN DO NOT USE HAMMER 3 WIPE AWAY EXCESS GLUE 6 gwo 4 HIDDEN CONNECTOR ASSEMBLY TECHNIQUES FOR LOCK NUT amp LOCK PIN 1 SET INCLUDES C CAM LOCK 1PC A CAM BOLT 1PC TOOL NEEDED SCREW DRIVER STEP 1 SCREW CAM BOLT A ONTO PRE SET PLASTIC NUT ON PANEL USE A SCREW DRIVER FOR TIGHTENING ATTENTION DO NOT OVER TIGHTEN THE CAM BOLT A STEP 2 ATTACH BOTH PANELS MAKE SURE YOU HAVE INSERTED THE CAM BOLT TO THE VERY DEPTH OF THE HOLE WITH RUBBER MALLET GENTLY CAUTION DO NOT USE HAMME2. 6X32mm 8 o3xiZan DETTE uer f SHELF HOLDER SHELF HOLDER ROUND HEAD SCREW TILTING PREVENT HARDWARE ES 15 si FLAT HEAD SCREW 4 PCS 24 PCS 1 SET 8 SETS y 11 12 3X12mm 13 ALLEN KEY GLUE 1 PC 1 PC P 3 10 PARTS LIST DRAWER FRONT PANEL DRAWER BACK PANEL DRAWER LEFT SIDE PANEL 1 PC 1 PC 1 PC A B C DRAWER RIGHT SIDE PANEL DRAWER BOTTOM PANEL LEFT SIDE PANEL 1 PC 1 PC 1 PC DJ m Ti RIGHT SIDE PANEL SHELF ACROSS BAR 1 PC 1 PC 1 PC L Y i G H I TOP PANEL BOTTOM PANEL DOOR 1 PC 1 PC 1 PC J K L SHELF SHELF BACK PANEL 2 PCS 1 PC 1 PC Zz E NOTE THE SURFACE WITH THE STICKER IS THE BACK SIDE P 4 10 STEP 1 ASSEMBLE DRAWER e USE SCREW 4 TO ATTACH DRAWER SIDE PANEL C amp D AND BACK PANEL B TOGETHER e INSERT DRAWER BOTTOM PANEL E INTO THE SLOTS OF SIDE PANEL C amp D e USE CAM BOLT amp CAM LOCK 2 TO ASSEMBLE DRAWER FRONT PANEL A AND DRAWER SIDE PANEL C amp D TOGETHER e USE ROUND BOLT 7 TO ATTACH KNOB 7 ONTO DRAWER FRONT PANEL A STEP 2 ASSEMBLE SIDE PANEL F amp G SHELF H AND ACROSS BAR 1 e FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 e USE FLAT HEAD SCREW 5 TO ATTACH DRAWER LIMIT STOPPER 5 ONTO AC
3. E OF SIDE PANEL F amp G THEN PUT SHELF N ON THEM AS SHOWN e INSERT THE PRE ASSEMBLED DRAWERS INTO THE PRODUCT BODY PROPERLY AS SHOWN P 8 10 STEP 6 ASSEMBLE BACK PANEL 0 e USE ROUND HEAD SCREW 13 TO ATTACH BACK PANEL 0 ON THE BACK OF PRE ASSEMBLED UNIT NOTE BEFORE YOU ASSEMBLE THE BACK PANEL PLEASE MAKE SURE THE 2 SIDE PANELS AND DOORS HAVE AN EVEN GAP BETWEEN THEM IF UNEVEN SHIFT THE SIDE PANELS AND ADJUST DOORS UNTIL EVENLY SPACED THEN ATTACH BACK PANEL kuch LI LA TI id d ri 4 L L bf P 9 10 STEP 7 ASSEMBLE TILTING PREVENT DEVICE 14 e USE ELECTRIC DRILL TO DRILL 2 SMALL HOLES ON THE DESIRED LOCATION OF WALL INSERT 2 GECKOS INTO THE 2 HOLES BY RUBBER MALLET USE TWO LONG SCREWS TO ATTACH ONE PLASTIC SLICE ONTO WALL THEN USE TWO SHORT SCREWS TO ATTACH ANOTHER PLASTIC SLICE ON THE BACK OF PRE ASSEMBLED PRODUCT e USE THE PLASTIC ROPE TO LINK THE PRODUCT AND WALL TOGETHER WARNING THE TILTING PREVENT HARDWARE MUST BE USED AS A PART OF ASSEMBLY OTHERWISE TILTING DANGER MAY BE CAUSED FAI AAA P 10 10
4. R THEN INSERT CAM LOCK C INTO PRE DRILLED HOLE ON PANEL MAKE SURE THE ARROW ON CAM LOCK C SET IN PANEL POINT TOWARD THE HOLE INTO WHICH THE CAM BOLT A HAS BEEN INSERTED AND INSERTED THE CAM LOCK C TO THE VERY DEPTH OF THE HOLE STEP 3 ROTATE THE CAM LOCK C CLOCKWISE TO SECURE CAM BOLT A BY TIGHTENING WITH A SCREWDRIVER DETAIL STEP PLEASE SEE THE BELOW PICTURE P 2 10 VERTICAL CONNECTION HORIZONTAL CONNECTION 1 La 2 1 Law 2 O koi a 4 3 4 We E 5 THANK YOU FOR PURCHASING THIS QUALITY PRODUCT BE SURE TO CHECK ALL PACKING MATERIAL CAREFULLY FOR SMALL PARTS WHICH MAY HAVE CAME LOOSE INSIDE THE CARTON DURING SHIPMENT COUNT ALL PARTS AND MATERIAL HARDWARE COMPARE WITH PARTS LIST TO BE SURE ALL PARTS ARE PRESENT IF ANY PARTS ARE MISSING OR DAMAGED PHONE FAX OR MAIL TO OUR CUSTOMER SERVICE DEPARTMENT FOR EFFICIENT AND SPEEDY SERVICE PLEASE INDICATE THE MODEL NUMBER AND CODE LETTER OF THE PART NEEDED HARDWARE LIST WOOD DOWEL CAM BOLT VELVET HOLE COVER FLAT HEAD SCREW FLAT HEAD SCREW 16 PCS CAM LOCK 4 PCS 4 PCS DRAWER LIMIT STOPPER 12 SETS 1 SET i FA as O G mm 8X30m 1 2 3 4X25mm 4 N 5 MAGNET LOCK KNOB ROUND HEAD BOLT TRON SLICE HINGE ROUND HEAD SCREW BOLT FLAT WASHER FLAT HEAD SCREW FLAT HEAD SCREW 1 SET 2 SETS SPRING WASHER 1 SET 2 SETS ZS K7 4 SETS T T J eh LI Gen i A osxionm 6 7
5. ROSS BAR 1 e USE CAM BOLT amp CAM LOCK 2 AND WOOD DOWEL 1 TO ASSEMBLE SIDE PANEL F amp G SHELF H AND ACROSS BAR I TOGETHER STEP 3 ASSEMBLE BOTTOM PANEL K AND TOP PANEL J FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 USE ROUND HEAD BOLT FLAT WASHER SPRING WASHER 8 AND WOOD DOWEL 1 TO ASSEMBLE BOTTOM PANEL K AND SIDE PANEL F amp G TOGETHER USE CAM BOLT amp CAM LOCK 2 AND WOOD DOWEL 1 TO ASSEMBLE TOP PANEL J AND SIDE PANEL F amp G TOGETHER USE THE VELVET HOLE COVER 3 TO COVER THE CAM LOCK HOLES USE FLAT HEAD SCREW 6 TO ATTACH MAGNET LOCK 6 ONTO ACROSS BAR 1 Bag A 7 P 6 10 STEP 4 ASSEMBLE DOOR L USE FLAT HEAD SCREW 10 AND HINGE 10 TO ASSEMBLE DOOR L ONTO SIDE PANEL G e USE ROUND HEAD BOLT 7 TO ATTACH KNOB 7 ONTO DOOR L e USE FLAT HEAD SCREW 9 TO ATTACH IRON SLICE 9 ONTO DOOR L P 7 10 STEP 5 ASSEMBLE SHELF M amp N AND PLACE DRAWER e INSERT SHELF HOLDERS 11 INTO THE HORIZONTAL HOLES INSIDE OF SIDE PANEL F amp G AND PLACE SHELF M ON THEM THEN USE FLAT HEAD SCREW 11 TO FIX SHELF M AND SHELF HOLDER 11 e INSERT SHELF HOLDERS 12 INTO THE HORIZONTAL HOLES INSID
Download Pdf Manuals
Related Search