Vigo VG6071RBCL3458 Instructions / Assembly
Contents
1. TO DIRECTLY HIT DOOR SEAL STRIPS MODEL VG06071 LEFT CORNER INSTALLATION RIGHT CORNER INSTALLATION MODEL VG06071 CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL A Use mild liquid household cleaners to keep metal surface bright and clean Rinse well and dry with a clean cloth B Remove dust with a soft damp cloth C Use rubbing alcohol to clean and remove grease oil paint and ink D Accidental scratches or stains will rarely show If they do show they can be easily removed with a liquid automobile polish E Use squeegee to remove excess water from the glass panel after every use N IMPORTANT e Do NOT use abrasive cleaners scrapers metal brushes or any items products that would scratch and or dull surface e Do NOT allow surface to come into contact with acetone nail polish remover dry cleaning solution lacquer thinner gasoline or any other similar product 10 MODEL VG06071 VIGO VIGO INDUSTRIES LLC VIGO SHOWER ENCLOSURE LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1 2010 VIGO offers the following limited warranty on each of its Shower Enclosure products the Product and the components thereof This warranty extends only to the original owner or end user for personal household use For commercial uses additional limitations apply VIGO warrants the structural glass component of the Product to be free from defects in workmanship and materials under normal use and service f2. in accordance with instructions supplied by VIGO and all applicable rules regulations and legislation pertaining to such installations This warranty does not apply unless the VIGO Product is installed by fully insured licensed professionals Vigo strongly recommends that such licensed professionals have experience in the installation of bathroom and kitchen products Installation of certain products including without limitation glass products i e shower doors and glass sinks by an inexperienced person may result in glass breakage and consequently cause personal injury or death VIGO is not liable for personal injuries or deaths to any persons or for any direct special incidental or consequential damage loss of time loss of profits inconvenience incidental expenses labor or material charges or any other costs resulting from the use of the product or equipment or pertaining to the application of the present warranty or resulting from the removal or replacement of any product or element or part covered by this warranty EXCEPT AS OTHERWISE PROVIDED ABOVE VIGO MAKES NO WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR COMPLIANCE WITH ANY CODE In any case VIGO cannot be held liable for any amount over and above the purchase price paid for the Product by the owner end user contractor or builder Commercial Limitations In addition to the above conditions and limitatio
3. 6071 C INSTALLING THE DOOR WARNING DOOR PANEL INSTALLATION REQUIRES TWO OR MORE PEOPLE TO ASSIST Place the door on the shims raising the door up 5 8 to accommodate the bottom door seal strip Align the door correctly using a level Mark two 2 holes on the wall for the mounting screws for each hinge Remove the door and drill holes into the wall where marked Place plastic anchors 7 inside the holes 5 Replace and screw the door securely to the wall with 1 5 8 screws 6 SEE FIG 4 i BATHTUB MODEL VG06071 AID f FIG 4 3 4 INSTALLING THE HANDLE Unscrew the handle holders from the handle assembly 5 Place the handle to the position on the door Place plastic washers supplied on each side of the door SEE FIG 12 Tighten the handle nuts from inside the shower TOP VIEW FIG 5 INSTALLING THE DOOR BOTTOM SEAL STRIP Clean the door glass panel 1 edges where the door bottom seal strip 4 is to be installed with rubbing alcohol The door bottom seal strip 4 is cut already to the proper size Verify that the lip of the seal strip faces toward the inside of the shower cabin before seal strip installation Install the seal strip according to the diagram SEE FIG 6 NOTE If the seal strips are not flat use a hair dryer to apply minimal heat and press the seal strip back into position FIG 6 N IMPORTANT e WAIT 24 HOURS BEFORE USING SHOWER e DO NOT ALLOW WATER
4. HEIGHT 3 DOOR 97027CL WITH HARDWARE _ EXTERIOR SIZES A DIMENSION WAS MEASURED AFTER SHOWER DOOR WAS COMPLETELY INSTALLED i 3 MODEL VG06071 WARNING WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER CABIN AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS BREAKAGE AND CONSEQUENTLY CAUSE PERSONAL INJURY OR DEATH BEFORE STARTING Compare items on your invoice with what you have received Carefully review the Packing List on page 2 If any items are missing contact Vigo Industries at 1 866 591 7792 REQUIRED TOOLS Square and or Phillips 1 and 2 screwdriver Flat head screwdriver Electric drill plus 1 4 and 5 16 drill bit depending on wall Level Measuring tape Pencil non permanent Clear silicone caulking Utility knife Shims WARNING e Handle fragile items with care to prevent injury or material damage e Glass on panels and doors is tempered glass and must never be cut to prevent personal injury NO IMPORTANT e Fiberglass or acrylic construction might not be sufficiently strong enough to support the shower door enclosure You should use the wood framing from behind the face edge of the stall to provide a secure mounting to the door Apply a bead of silicone between the walls and base of the stall e For optimum performance you should install the shower door perfect
5. VIGO VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE MODEL VG06071 SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information Always observe the instructions indicated by these symbols I WARNING Instructions that if ignored could result in death or serious personal injury caused by incorrect handling or installation of the product These instructions must be observed for safe installation IMPORTANT Maintenance and other important non personal injury and non material damage instructions or statements that should be observed It is highly advised to dry fit the unit prior to any installation INSTALLATION INSTRUCTIONS FOR STANDING SHOWER CABIN VIGO OWNER S MANUAL PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Packing List Door 1pc Hinge 2pc Side seal strip 1pc Door bottom seal strip 1pc 1pc is extra Handle assembly 1pc Hex screw 1 5 8 10pc Plastic anchor white 10pc Clear PVC shims 1 pack 0 NOIA DVDMN GLASS THICKNESS 8mm NOTE INSTALLATION MUST BE DONE BY A QUALIFIED LICENSED PLUMBER D MODEL VG06071 VIGO 1 DOOR 97027CL 2 HINGE ASSEMBLY 98071 3 SIDE SEAL STRIP WITH FLANGE 96017 4 DOOR BOTTOM SEAL STRIP 96018 5 DOOR HANDLES 98070 A eo 6 HEX SCREW 1 5 8 7 PLASTIC ANCHOR 8 CLEAR PVC SHIM 98039 98038 MISC CES in OS DIMENSION A
6. ion STUD FIG 1B CAUTION n e GASKETS NEED TO BE IN BETWEEN ALL GLASS AND METAL CONTACT FAILURE TO DO SO CAN LEAD TO BREAKAGE AND POTENTIAL BODILY HARM INSTALLATION STEPS A INSTALLING THE WATER SIDE SEAL STRIP 1 Clean all glass panel edges receiving seal strips with rubbing alcohol SEE FIG 1 2 Cut seal strip 3 according to seal strip diagram SEE FIG 1 3 Install the side seal strip according to seal strip diagram making sure that the flange is on the inside of the shower SEE FIG 1 NOTE If the seal strips are not flat use a hair dryer to apply minimal heat and press the seal strip back into position MAKE SURE THE FLANGE IS ON THE INSIDE OF THE SHOWER 1 3 HINGE OUTLINE 3 FIG 1 MODEL VG06071 N gt W HINGE INSTALLATION Clean the glass surface where the hinges 2 are to be installed with rubbing alcohol Position hinges on the door glass panel Place a shim 8 between the glass and the hinge on the bottom The metal should not rest on the glass SEE FIG 3 Place gaskets on each side of the door glass panel Screw the hinges to the door glass panel with the hex key supplied SEE FIG 2 THIN GASKETS VIEW FROM INSIDE THE SHOWER THIN GASKETS J fe Cee lg AC Ge HEX SCREWS FIG 2 HINGE 2 A S DOOR GLASS o PANEL 1 j INSIDE VIEW CLEAR PVC SHIM 8 DOOR GLASS cea PANEL 1 PVC SHIMIB SIDE VIEW FIG 3 MODEL VG0
7. ion shall be discharged upon tender of replacement or repair The customer s refusal to accept the tender terminates VIGO s warranty obligations Certain models are pending approval Certification may be ended by VIGO or certification agencies without notice 11 MODEL VG06071
8. ly level on a level surface e When installing use heavy duty gloves e FOR THE MATTE GLASS MODELS Oil secretions from skin will leave transparent spots on the matte side of the glass Use a degreasing non abrasive cleaner to remove these secretions The same will happen if you get silicone on the matte glass Use a silicone remover to remove these stains N NOTE The design of this unit leaves open space in the back of the tub leaving potential for water leakage IMPORTANT THE CLEAR GLASS MODEL HAS A REVERSIBLE DOOR AND CAN BE INSTALLED TO THE RIGHT OR LEFT SIDE SEE CONFIGURATION DIAGRAM BELOW VIGO DALILA BATHTUB DOOR DOOR PANEL ceti DOOR PANEL RIGHT CORNER LEFT CORNER INSTALLATION FIG 1A GLASS CONFIGURATION DIAGRAM INSTALLATION A MODEL VG06071 VIGO PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION 1 Remove the plastic layer from the base tub border if needed Do NOT remove the plastic layer off the plastic platform of the base tub 2 Properly apply silicone to the wall and base joints N IMPORTANT e Toprevent damage to the finish you should protect the tub bottom with a cardboard protector before beginning the installation e Ensure that there is sufficient structural support behind the shower wall to hold the weight of the shower door If there is insufficient Support then reinforce the shower walls with wooden studs prior to shower door installation SEE FIG 1B typical for right and left door installat
9. ns the warranty period for products installed for commercial applications or used in commercial ventures is one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer VIGO is not responsible for loss of use or profit under any circumstances If the product is used as a display the warranty period begins when the product is placed on display This warranty gives the owner end user specific legal rights The owner end user may also have other rights which can vary from one state or province to another Warranty Service In order to obtain service provided under this warranty during regular business hours contact the dealer or distributor who sold the unit or contact VIGO directly VIGO will provide the warranty service described above when the following conditions have been met the failure is of the nature or type covered by the warranty the user has informed an authorized VIGO Agent or VIGO s warranty service department representative of the nature of the problem during the warranty period conclusive evidence e g proof of purchase or installation is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period an authorized independent service person or company representative has been permitted to inspect the product during regular business hours within a reasonable time after the problem was reported by the user VIGOs warranty obligat
10. or the period commencing from the initial date of purchase by the owner or end user contractor or builder from VIGO or an authorized VIGO dealer through the lifetime of the original owner or end user VIGO warrants the hardware components of the Product to be free from defects in workmanship and materials under normal use and service for a period of two 2 vears from the initial date of purchase by the owner or end user contractor or builder from VIGO or an authorized VIGO dealer VIGO warrants the seal strip components of the Product to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the initial date of purchase by the owner or end user contractor or builder from VIGO or an authorized VIGO dealer Subject to the Warranty Service provision below any product reported to the authorized dealer or to VIGO as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of VIGO This warranty extends to the original owner or end user and is not transferable to a subsequent owner Neither the distributor authorized VIGO dealer nor any other person has been authorized to make any affirmation representation or warranty other than those contained in this warranty Any affirmation representation or warranty other than those contained in this warranty shall not be enforceable against VIGO or any other person VIGO reserves the
11. right to modify this warranty at any time it being understood that such modifications will not alter the warranty conditions applicable at the time of sale of the products in question Limitations This warranty shall not apply to instances of incorrect operating procedures breakages or damages caused by fault through improper installation carelessness abuse misuse misapplication improper maintenance or alteration of the Product as well as chemical or natural corrosion accident fire flood an act of God or any other casualty Avoid abrasive cleaners steel wools and harsh chemicals as these will scratch damage and or dull the product and or finish and void this warranty The owner end user of the Product covered by the present warranty is entirely responsible for its proper installation and any applicable plumbing or electrical wiring VIGO neither installs nor Supervises the installation nor hires a contractor for this purpose consequently VIGO cannot be held responsible for any default breakage or damages caused thereby or resulting thereof either directly or indirectly The owner end user must provide access to the components of the Product as described in the installation guide so that VIGO can execute the warranty specified herein If such access is not available all expenses to provide said access will be the responsibility of the owner end user This warranty does not apply to Products that have not been installed or operated
Download Pdf Manuals
Related Search