Aston SEN986-CH-32-10 Installation Guide
Contents
1. Figure 9 10 Place the Hinge Stationary glass 01 bares into position in shower area and install glass AA clamps 08 to Hinge Stationary glass 01 putside See Figure 10 for detals he l ne Pail bl outside Figure 10 11 Place the Stationary glass 03 into position in shower area and install glass clamps 08 to Stationary glass 03 See Figure 11 for detals Figure 11 12 Press the Magnetic strips 12 onto the vertical edge of the Glass Door 02 and Stationary Glass Panel 03 See Figure 12 for details 13 Attach the Hinges 09 to the Hinged stationary glass 01 Smooth flat surface of Hinges 09 should be installed on outside of stationary glass 01 Place a piece of flat timber 1 2 thick on the threshold or shower base Carefully position Glass door 02 on the flat timber and attach shower door to hinges Level up the Glass door next to the Hinged stationary glass and fasten the hinges on the Glass door If needed adjust the position of the glass to make sure the Magnetic strips 12 are tight from top to bottom See Figure 13 for details nil Figure 12 LA A IEA A O O NON A N A N A NJ Figure 13 14 Marks on the Side S2. INSTALLATION AND OWNER S MANUAL Please select your shower enclosure model or shower enclosure style from the selection below for easy installation ATTENTION This door is extremely heavy and the hinges on this door must be attached to the studs or to preinstalled 2 X 6 wood reinforcement behind the wall Pi ee 2 7 ge Pe 7 7 WELAT TEE E E i L p L ig i p g i ie Style A Style B Please carefully read these instructions before you begin to install the products IMPORTANT ASTON reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the www astonbath com 11 14 RevA SSS Before you start Thank you for purchasing your Aston shower enclosure We hope that it will provide you with years of satisfying use and enjoyment Please read this manual carefully because it contains information and instructions about the proper installation of the unit If you do not follow certain conditions of installation and maintenance your warranty may be affected 1 Inspect boxes for shipping damage If the product has been damaged is missing parts or has a finishing defect please contact our customer support department within 5 business days of delivery date 2 NOTE You should consult your local building codes with questions on installation compliance standards Plumbing and building codes vary by
3. carefully inspect all parts and identify all parts using detailed diagram in your manual as a reference Before discarding the packaging check for any parts or small hardware bags that may have been overlooked STYLE A Shower enclosure with support bars Diagram A Diagram B and Diagram C must be used for assembly Pages 5 14 STYLE B Shower enclosure with glass shelves Diagram A Diagram B and Diagram D must be used for assembly Pages 5 13 15 Shower Enclosure Assembly and Installation Style A and B NOTE Please use parts from Diagram A and Diagram B or C depends on your model style for the Shower enclosure assembly and installation ATTENTION A minimum of two people are required for the next assembly steps LAB ae etetee Lis aa a ie a a a De een ss fe ee ey Style A Style B 1 Measuring from the back corner in the shower mark the shower wall for Stationary Glass Panels Refer to the size of your model in the table below wre ts ty GLSD1022 GLSP SEN99118 1o GLSD1025 GLSP SEN99118 GLSD1028 GLSP SEN98618 GLSD1025 GLSP SEN99122 GLSD1028 GLSP SEN99122 E See Fig 1 for details RL pi Note This measurement is from the back corner in shower pe to the outside of glass Figure 1 2 Remove pre installed screws from pre assembled Glass clamps 08 Align the Glass Clamps 08 with notches in the Hinged Stationary glass 01 and install Glass clamps 08 t
4. purchaser of the Product resides and 2 the Product must be maintained as described in the owner s manual supplied with the Product For glass and acrylic panels the customer must a open and inspect the Product upon delivery without releasing the delivery driver until visual verification that the Product arrived in a good and acceptable condition and b clearly notate damage on the delivery acknowledgment receipt Failure to do so and any damage discovered to glass or acrylic panel after delivery will be repaired or replaced at the sole discretion of Aston Global 17 THIS WARRANTY DOES NOT COVER 1 Product installed in buildings other than single family dwelling units 2 Product installed outdoors or any other non standard bathroom location 3 Component parts not manufactured by Aston Global 4 Workmanship of any installer of Aston Global Product This warranty does not assume any liability of any nature for unsatisfactory performance caused by improper installation or any damages to property resulting from improper installation or use of the Products including but not limited to flooring subfloor tile walls sheet rock concrete board paint plumbing fixtures and ceilings 5 Labor costs incurred in the removal disassembly reassembly or installation of the Product s including replacement Products issued under the Warranty or costs for transportation to Aston Global and any other materials necessary to return Produc
5. the brackets See Figure 19 for detals a ae a a ae a a p i ji W y i p j p A Care and Maintenance As with any other luxury item maintenance and care are critical to the long lasting quality and enjoyment of your shower door and tray The proper care and maintenance outlined in this section are necessary to ensure the longevity of the unit Damage caused by not following the care and maintenance guidelines in this section is not covered under the manufacturer s warranty The glass doors and panels can be cleaned using any commercially available glass cleaner We recommend that you clean the glass daily and squeegee the glass with a silicone or rubber squeegee after each use to help prevent water spots 16 Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR ASTON GLOBAL BATHROOM PRODUCT BY USING THE PRODUCT YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS SHOWER DOOR SHOWER TRAY Aston Global Inc Parts Only Limited Warranty 5 years Aston Global Inc Aston Global warrants to the original retail purchaser Owner of any Shower Door Tray product Product at the original installation site for a period of Five 5 years from date of purchase whether directly from Aston Global or an authorized reseller that the Product manufactured by Aston Global is free from manufacturing defects in materials and workmanship when used unde
6. the wall bracket to the marked area on shower wall and mark the drilling location on shower wall Drill the hole using 5 16 drill bit If your surface is prone to cracking or chipping then is recommended that you pilot drill first using a smaller drill bit and then step up to the final size Insert the Wall anchor 05 and fasten the bracket to the wall with M5X60 screw 06 Attach the Support bar 04 to the wall bracket and the Hinged Stationary Glass 01 with gasket in place and tighten the set screws to secure in place See Figure 17 for detals 18 Apply silicone sealant to edge of Stationary glasses 01 03 and shower wall and Stationary glasses 01 03 and shower base See Figure 18 for details 12 SA y y X IN outside D Ae Sy Te y Ay DA Figure 18 Please continue your installation e Style A for Support bar installation e Style B for Glass shelves installation Glass Shelve installation mounting holes Style A 13 Support Bar Assembly and Installation Style A NOTE Please use parts from Diagram C for the Support Bar assembly and installation 19 Position the Support bar 04 on the Stationary glass 03 Using a level check support bar is level and mark the bracket s location on the shower wall YU Z ee j outside Remove the Support bar 04 from the Stationary glass 0
7. 3 and detach the wall bracket Position Sy the wall bracket to the marked area on shower _ 2 Her wall and mark the drilling location on shower wall Be Drill the hole using 5 16 drill bit P l C If your surface is prone to cracking or chipping p v then is recommended that you pilot drill first using a smaller drill bit and then step up to the final AP p size ae Insert the Wall anchor 05 and fasten the bracket 4 f ia to the wall with M5X60 screw 06 se Figure 19 Attach the Support bar 04 to the wall bracket and the Stationary Glass 03 with gasket in place and tighten the set screws to secure in place See Figure 19 for detals i ae ae a A ee p K a j f p H A 14 Glass Shelves Assembly and Installation Style B NOTE Please use parts from Diagram D for the Glass Shelves assembly and installation 19 Mark the hole locations on shower wall for attaching glass shelve brackets Drill the holes using 5 16 drill bit If your surface is prone to cracking or chipping then is recommended that you pilot drill first using a smaller drill bit and then step up to the final size Insert the Wall anchors 05 Attach the Shelf brackets without nut 15 to the wall using the M4x60 screws 07 Attach the Shelf brackets with nut 14 to the Stationary glass panel Insert the Glass shelves 13 into the Shelf brackets and fasten the set screws at the bottom of
8. ives shall not be liable for any injury loss cost or other damages whether incidental or consequential arising out of any defect covered by this Warranty including and without limitation loss of use of the Product and cost for removal of defective Product even if Aston Global has been advised of the possibility of such damage The liability of Aston Global under this Warranty if any shall not exceed the original amount paid for the Product covered by the Warranty Coverage under this Warranty shall commence as of the original date of purchase and the duration of such coverage shall not extend for any reason whatsoever beyond the stated time period The 18 Customer is required to provide adequate access the Product for any repair or inspection Aston Global shall not be liable for expenses or damage which may include but are limited to water damage removal of any and all common building product such as tile flooring wood sheet rock plumbing fixtures concrete board vanities bathtubs and toilets or any other custom items THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE ASTON GLOBAL S FAILURE TO ENFORCE ANY TERMS OR CONDITIONS STATED HEREIN SHALL NOT BE CONSTRUED TO BE A WAIVER OF SUCH PROVISION For prompt service notify the original installer who in turn will notify the Aston Global distributor who supplied the Product If this does not result in prompt service contact A
9. location 3 Before installation inspect installation surfaces or level and have to the strength to support the heavy weight of this shower door assembly This shower door should only be installed using the connection point to the studs or to pre installed 2x6 wood reinforcements behind the wall 4 This Shower Enclosure assembly is very heavy and requires professional installation Aston Shower enclosures feature e Tempered Safety Glass e High quality hardware WARNING The Aston Shower enclosure is designed to be used with tiled walls If you are using a pre made Acrylic ABS FRP shower stall that will be thicker than average plus tile then you must consider the offset of the pre made panel thickness If applicable the shower tray has 1 4 of tolerance for the oversized wall thickness Certifications All Aston Shower enclosures are 3rd party tested to meet the following US Canadian and International Standards e CPSC 16 CFR1201 II ANSI 297 1 2009 Class A e CSA B45 Series 02 Installation Guide Please read and follow the installation instructions and guidelines in this section Failure to follow the recommended instructions and installation techniques may lead to possible damage to the unit or the surrounding area This can affect warranty claims ATTENTION This unit requires assembly A minimum of two people are required for assembly as several of the sections can be large and unstable until assembled You will
10. need the following tools Qo ky OS s Caulk Tape Measure Pencil Phillips Screwdriver eN lt H D Xy j oS a Aa 10 D Caulk Gun Level Electric Drill Drill bit 6 Hammer Locate the accessory box and remove the individual screw and hardware packages Lay them out in sequential order to aid in completing the rest of the installation Detailed Diagrams of Shower Enclosure Components Diagram A Diagram B Diagram C Diagram D Hinged Stationary Shower Door Stationary Glass Panel Stationary Glass Panel Glass Panel with Top Brace with Glass Shelves CS 4 N 5 E 9 P 7 ee ANG oie 5 a ge fe 10 8 6 ext 6 7 l me sca 12 y 11 janie 8 gj i ad N 1 3 8 D s gt hcg 12 12 14 Ml NM Se 4 cL k 3 Diagram A 01 Hinged Stationary glass panel 1pc 06 M5 X 60 screw Supportbar _ _ M4 X 60 screw Wall anchor 4pcs 08 Glass clamp SCS Diagram B Side strip 3 sections to cut 1pc 08 Handie tp 11 Bottom anti water strip Magnetic strip Diagram C 09 Stationary glass panel M4 X60 screw Support bar ipce 08 Glass clamp Wall anchor Fos MSX60screw me o T Diagram D Stationary glass panel Magnetic strip Wall anchor Glass shelf M4 X 60 screw Shelf Bracket with nut 08 Glass clamp Shelf Bracket without nut PLEASE NOTE During unpacking
11. o Stationary glass 01 Noted Smooth flat surface of Glass clamp 08 should be installed on outside of glass door See Figure 2 for details 3 Remove pre installed screws from pre assembled Glass clamps 08 Align the Glass Clamps 08 with notches in the Stationary glass 03 and install Glass clamps 08 to Stationary glass 03 Noted Smooth flat surface of Glass clamp 08 should be installed on outside of glass door See Figure 3 for details a 7 ay NS outside 4 z eo A l N outside N C Figure 2 fo Ssg YU fa outside outside Figure 3 4 Carefully position the Stationary glass panels 01 and 03 against the shower wall aligning the outside edge of Stationary glass panels 01 and 03 with marked dimensions from earlier step Check with level the plumb Stationary glass panels 01 and 03 Note The Stationary glass panels 01 and 03 should be vertical and in plumb Note The unit shown in figure 4 illustration is showing a left hand hinge assembly If you need a right hand hinge assembly install the Hinged stationary glass panel to the right side of shower opening See Figure 4 for details 5 Mark the position of the the Glass clamps 08 on the shower wall and shower floor from the inside shower See Figure 5 for details 6 Carefully place the Stationary glass panel
12. r normal conditions and when such Product has not been modified or changed in any manner after leaving Aston Global s warehouse or plant If any Product manufactured by Aston Global is found to have manufacturing defects in materials or workmanship such Product will be repaired or replaced by Aston Global This warranty applies only against defects discovered within the warranty period and extends only to the original purchaser of the Product Parts repaired or replaced under the terms of this Warranty will be warranted for the remainder of the original warranty period only Proof of purchase is required to exercise this Warranty Aston Global may at its option examine and inspect the alleged defective Product and Aston Global may request that parts be returned to Aston Global at Owner s expense for factory inspection The determination as to whether Product shall be replaced or in the alternative repaired shall be made solely by Aston Global If a Product is determined to be covered by the above Warranty Aston Global will ship the replacement part s to Customer by either ground shipping or US postal service Increased costs for expedited delivery if requested by Customer are the responsibility of Customer Parts not currently in stock may require up to a 6 week delivery time after placement of order The above warranty is subject to the following conditions 1 the Product must be installed in a single family dwelling unit where the original
13. s 01 and 03 aside Remove the Glass clamps 08 from the Stationary glass panels 01 and 03 Next position and align the Glass clamps 08 with marked location on shower wall and shower floor Mark the drill hole locations for mounting the Glass clamps 08 to shower wall and shower floor See Figure 6 for details Figure 4 inside R Y inside Figure 5 op inner part Figure 6 7 Using the appropriate drill bit for your wall surface drill each hole location with a 5 16 diameter drill bit Using the appropriate drill bit for your floor surface drill hole location with an 1 8 diameter drill bit for Aston shower base use a 5 16 diameter drill bit for other surfaces and plastic wall anchor See Figure 7 for details NOTE If your surface is prone to cracking or chipping then it is recommended that you pilot drill first using a smaller drill bit and then step up to the final size 8 Install the plastic Wall anchors 05 provided into the drilled holes on wall See Figure 8 for detals 9 Attach the Glass Clamps 08 to shower wall and to shower floor using M4x60 screws The Glass clamps 08 should be positioned so that the single hole is facing toward the inside of shower See Figure 9 for detals va ye or ee Figure 7
14. ston Global Inc at the address below with details in support of the warranty claim For any questions about coverage of this Warranty contact Aston Global at the address below Aston Global offers free phone support for the life of the Product to the original Owner The Warranty applies only to Products manufactured on or after January 1 2012 This Warranty may not be combined with any other warranty offered by Aston Global 19 ASTON ESCAPE THE EVERYDAY Customer Service 877 424 9699 Aston Global Inc 10480 Brockwood Rd Dallas TX 75238 If further assistance is needed or you have a question please visit our web site at www astonbath com
15. t to Aston Global 6 Any Product that has been damaged as a result of being improperly serviced or operated including but not limited to the following operated with insufficient water allowed to freeze subjected to flood conditions operated with water conditions or additives which cause unusual deposits or corrosion in or on the Product or subject to any other abuse or negligence 7 Any Product that has been damaged as a result of natural disasters including but not limited to lightning fire earthquake hurricanes tornadoes or floods 8 Product used for any purpose other than residential bathroom usage LEGAL DISCLAIMERS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED IN THEIR ENTIRETY WITH RESPECT TO ALL PURCHASERS OR OWNERS FAILURE TO RETURN THE WARRANTY CARD SHALL HAVE NO EFFECT ON THE DISCLAIMER OF THESE IMPLIED WARRANTIES ALL EXPRESS WARRANTIES SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS LIMITED WARRANTY AND EXCLUDE ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES RESULTING FROM THE BREACH OF ANY EXPRESS WARRANTY Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply No dealer distributor service company or other party is authorized to change modify or extend the terms of this warranty in any manner whatsoever Aston Global and it representat
16. trip 10 at 8 146 4 te 2 N 48 3 and 8 15 RS Carefully cut the seal at the appropriate 8 46 marks then install the individual seals on the A 48 3 approprate sections of glass door e from the top edge of glass door to upper body of the top hinge 8 46 3 e from the lower body of upper hinge to A the upper body of the bottom hinge 48 8 g 1 UY N XS e from the lower body of bottom hinge to 146 V6 above the shower base 8 14 a l Figure 14 Remove the timber plate fully open the glass door and press the cut strips on the vertical edge of the glass door See Figure 14 for details 15 Measure the bottom of the Glass door 02 from the Yj Side strip 10 to the vertical edge of Magnetic strip 12 Dai inside Cut the Bottom anti water strip 11 to the size of measurement and press onto bottom edge of glass door LA See Figure 15 for details outside Figure 15 16 Install the Handle 08 to the Glass Door 02 using the hardware provided See Figure 16 Inside Outside Figure 16 11 17 Position the Support bar 04 on the Hinged Stationary glass 01 Using a level check support bar is level and mark the bracket s location on the shower wall Remove the Support bar 04 from the Hinged Stationary glass 01 and detach the wall bracket Position
Download Pdf Manuals
Related Search