Barclay Products TKCTS7H67-ORB5 Installation Guide
Contents
1. threads For mounting of the shower set to the house water supply line see your local plumber To Connect Shower Set to Tubes 1 2 First remove the round rubber washer from the end of each water supply tube and dispose of them Put the cone washers on the tub and connect the end of each water supply tube Then slide the 1 2 connecting nuts over the opposite ends of the supply tubes and up to the cone washers Twist the connecting nuts over the cone washers and thread the nuts onto the nipples Connect the other ends of the water supply tubes to your house water lines Consult your local plumber for assistance NOTE Please seek professional help if you have copper plumbing in your home Cleaning Instructions Wipe this whole set off with warm water and a soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the protective lacquer coating and leave the brass exposed causing it to tarnish 12 21 07 P 84724491234 www barclayproducts com Straight Bath Cat No Supply 997 BARCLAY INSTALLATION INSTRUCTIONS Parts Included e 4 Cone Washers 2 Decorative Locknuts 2 Supply Tubes e 2 Escutcheons 2 Locknuts Tools Needed e Adjustable Wrench Set of Crescent Wrenches Pliers Teflon Tape use as a sealant on all male threaded tubing This water supply tube kit includes the parts listed above ONLY The faucet must be purchased separately Cone Washer Decorat2. Tub Rim Mounted fa Cat No Faucet with Hand Shower 4601 BARCLAY Shower Assembly amp Tub Mount Instructions 1 2 Apply teflon tape to both ends of the hot and cold supply nipples Install a washer in the cradle nut and thread the cradle onto the valve F i INSTALLATION INSTRUCTIONS Parts Included e 1 Valve Body 1 Shower Head 1 Hose e 1 Cradle e 4 Washers e 1 Elephant Spout 2 6 Elbow Mounts e e 2 Cone Washers 2 Large Locknuts 2 Connecting Nuts e Tools Needed e Adjustable Wrench Slip Joint Pliers Pipe Putty or Teflon Pipe Tape NOTE Handles are identified HOT and COLD The hot handle must be to the left and cold to the right Be sure the water supply is turned off before starting installation Cushion the wrench or slip joint pliers with an old cloth to protect the finish of the fixture Turn off the water supply Align the valve assembly with the elbow mounts and secure with the nuts on the elbow mounts Tighten with a wrench or pliers Tread the tapered ends of the nipples into the elbow mounts on the outside of the tub Thread the large locknuts onto the other ends of the nipples and secure the shower set to the tub assembly Tighten with a wrench Install washers on the hose ends and attach the hose to the cradle f and shower head DO NOT OVER TIGHTEN Connect the water supply nipples to the water supply tubes for tub mounting of the water supply tubes with 1 2
3. ive B S Locknut Supply Tube m P Escutcheons Locknut Ss To Assemble Tubes g 1 First be sure to shut off the the water supply Remove old water supply tubing Put a cone washer with the wide end of the washer inward onto the upper end of each supply tube Cone Washer 2 Slide a decorative locknut up to the top of each supply tube and put on a cone washer 3 On the bottom of each supply tube slide one of the escutcheons up the tube partway then slide the locknut up the end of each tube directly under the escutcheon 4 Put another cone washer with the wide end of the washer upward onto the bottom end of the tube To Install Tubes 1 Attach the bottom end of each supply tube to the water supply tubing in your floor by screwing the locknut down tightly Let the escutcheons slide down to the floor 2 Attach the upper end of one supply tube to the cold side faucet supply tube located on the rear of your tub by inserting the supply tube into the faucet supply tube and tightly screw the decorative locknut over the two for a tight fit 3 Repeat steps 1 2 using the other supply tube and connecting it to the hot side faucet supply tube NOTE Please seek professional help if you have copper plumbing in your home Cleaning Instructions Wipe this whole set off with warm water and a soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the protective lacquer coating and
4. leave the brass exposed causing it to tarnish 3 17 08 P 847 244 1234 www barclayproducts com Leg Tub Cat No 4 Drain 9999 BARCLAY INSTALLATION INSTRUCTIONS Parts Included e Top Overflow Tube 1 Bottom Shoe 2 Top Waste Flange 3 Face Plate 4 Exposed Tee 5 e Face Sponge Gasket 6 e Waste Gasket 7 Lift Stop 8 2 1 1 2 Nut and Washers 9 Face Plate Screw 10 1 1 2 x 6 Tube 11 1 1 2 O D Escutcheon 12 Tools Needed e Wrench Pliers Teflon Tape use as a sealant on all male threaded tubing Tube Cutter Plumbers Putty To Assemble Tubes 1 Assembled 3 and 8 screw into 2 7 is on top of 2 beneath the tub Place a bead of plumbers putty around bottom of 3 to seal to tub and protect from leaks Then tighten 3 into 2 2 Assemble overflow Follow diagram 3 Set 1 in place 4 Place Tee 5 on shoe Cleaning Instructions 5 Trim bottom of tube 1 to fit into Tee 5 Wipe this whole set off with warm water and a 6 Trim tube 11 to fit soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the 7 Tighten the nuts protective lacquer coating and leave the brass exposed causing it to tarnish NOTE Please seek professional help if you have copper plumbing in your home 1 8 08 P 847 244 1234 www barclayproducts com cry Cat No D 4145 Z Shower Rod BARCLAY INSTALLATION INSTRUCTIONS Parts I
5. ncluded e 2 Corner pieces 1 Back bar no inserts 1 Front bar with grey inserts e 2 331 D Rod loops 2 300 Flanges 8 Wall screws 2 Set screws Tools Needed e Pencil Drill e Measuring Tape Inserts Inserts o 441 D Pad Loop a m Ter 7300 Flanges E i 331 D Rod Loopl i 1 Attach the bent corner rods to the straight rods by sliding on to the gray inserts on straight rods 2 The large straight rod fits into the 331 D Rod loops 3 The looped portion of the 331 fits over the D Rod corner pieces as shown 4 The flanges attach to the wall measure for proper distance 5 The D Rod assembly fits into flanges and is secured with set screws To attach faucet assembly use 336 Double eye loop sold separately 6 The 336 double eye loop must be put on the desired side of the D Rod before back straight rod is attached 7 The riser for the faucet assembly will fit through the other opening in the 336 9 14 09 P 847 244 1234 www barclayproducts com
Download Pdf Manuals
Related Search