DreamLine SHBW-1450743-01 Installation Guide
Contents
1. See Fig 33 for details G H 1 1 Fig 33 3 1 2 28 Mark the location for the Shelf brackets 04 according to 3 1 2 the measurements in Fig 28 and Fig 29 1 Drill the holes using 5 16 drill bit and insert the Wall FA anchors 06 3 2 t See Fig 34 for details 1 Ka 5 16 go 1 3 Fig 34 Ver 1 Rev 1 20 29 Mount the Shelf brackets 04 to the wall using the Countersunk screws ST4 2x30 07 NOTE the padded set screw of the Glass bracket should be facing down Slide the upper Glass shelf 05 into the upper Shelf brackets and tighten the set screws at the bottom of the brackets Then slide the bottom Glass shelf in place Tighten the set screws on the bottom Shelf brackets as well See Fig 35 and Fig 36 for details Fig 36 Ver 1 Rev 1 21 Product maintenance To insure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface Acrylic cleaning procedure Acrylic should be cleaned with warm water and a clean nonabrasive cloth If desired a mild non abrasive detergent may also be use2. Fig 22 Vo Ta Ver 1 Rev 1 18 Slide the right edge of the left Back panel 09 all the way behind the Center cover 10 and push the Back panel against the wall Slide the left edge of the right Back panel 09 all the way behind the Center cover 10 and push the Back panel against the wall as well You can adjust the position of the Back panels before the sealant sets Apply equal pressure to the whole surface of the Back panels from top to bottom See Fig 23 and Fig 24 for details Fig 24 Fig 23 Ver 1 Rev 1 02 to the corner of the shower using the Countersunk screws ST4 2x30 07 Do not fully tighten the screws at this time leave them loose for further installation 19 Mount the Corner cover 1 See Fig 25 for details 20 Apply the sealant to the entire surface of the reverse side of the Side panel 01 Also apply the sealant around the drilled holes See Fig 26 for details Fig 25 Fig 26 Ver 1 Rev 1 21 Slide the narrow edge of the Side panel 01 behind the Corner cover 02 Align trimmed edge of the Side panel from Step 9 with the marked line on the wall in Step 7 and push the
3. Fig 30 Ver 1 Rev 1 ATTENTION Prior to the next step please be sure the part of the wall for installation of the Decorative edge molding 03 is clean dry and free from soap oil and any construction debris 25 Gently remove the plastic tape from the adhesive side of the Decorative edge molding 03 and firmly press it to the edge of the Side panel 01 from top to bottom See Fig 31 for details 26 Apply caulk along the top edges of RU the Side panels 01 and the Back ae panels 09 A i Apply caulk along the connection of the bottom edges of the Side panels and bottom edges of the Back panels with the Shower base See Fig 32 for details ATTENTION Installation of your QWALL 5 Acrylic shower wall is complete If you want to install Glass shelves 05 to your Shower follow to the next step 1 Side Panel Wall DN Decorative Molding A Side Panel Decorative Molding KN Fig 31 Fig 32 Ver 1 Rev 1 27 Determine the desired height for the wat Glass shelves 05 and mark the OK locations on the wall NOTE The Glass shelves can be installed either two in one corner or one in each Glass Shelves Installation Instruction
4. 4 Determine the position of both Back panels 09 NOTE a The Narrow side 2 3 4 of the Back panel cannot be trimmed and should face the center of the back wall as shown b The Wide side 3 1 8 of the Back panel must be trimmed to the size of the back wall if necessary and should face the corner See Fig 4 for details P lon e Iq h Yo Fig 3 Ng Fig 4 hy 9 Ton Ver 1 Rev 1 5 Measure the Back Panel 09 Width of the Back Panel has to be less than or l equal to the distance between the center line and the corner line on the back wall in Step 3 i L lt W 2 l If the width of the Back Panel is greater than a the distance between the center line and the corner line on the back wall in Step 3 you have to trim the Back Panel to fit your measurement See Fig 5 for details Fig 5 6 Measure from the narrow edge of the by Back panel 09 and place a mark at a ine 72 distance of W 2 that you measured nen in Step 3 r From this mark draw a straight line by from top to bottom along the wide L edge of the Back panel 5 See Fig 6 for details Line to cut Fig 6 Ver 1 Rev 1 7 Place the Back Panel 09 onto a flat piece of plywood or particle board Use a sharp industrial knife and a T square to score along the marked side ends
5. QREAMLINE ream In style QWALL 5 2 2 Back Panels SHOWER ACRYLIC WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Back Wall please visit www BathAuthority com Ver 1 Rev 1 Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Shower Door Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the pro
6. See Fig 11 for details Fig 11 10 Place the Side panel 01 on a flat piece of plywood or particle board Use a sharp industrial knife and a T square to score along the marked wide ends of the Side panel and continue scoring until you have fully AN cut through the panel A AN NASIS N S 7S GAMA Vhs See Fig 12 and Fig 13 for details IWN QQY TNS X V QQ SON WY WR QW Wy HH fpH LL LIkX LAAg 1 Ver 1 Rev 1 9 11 Take exact measurements of the fixture on the wall e from the 1 one inch line in the corner of the shower to the fixture A B C e from the bottom of the wall of the shower to the fixture E F See Fig 14 for details 1 a 4G E L B Fig 14 Ver 1 Rev 1 12 Determine which Side panel 01 will be installed on the side wall with the fixture Mark the fixture location on the Side panel according to the measurements taken in Step 11 See Fig 15 for details 13 Drill the holes for the fixtures in the Side panel 01 using the proper diameter saw bit or a handheld jig saw See Fig 16 for details A D B C Fig 15 Fig 16 Ver 1 Rev 1 11 14 Attach the Center cover 10 1 vertically Acrylic Back Panel and Side Panel
7. Side panel against the wall NOTE Make sure the drilled holes on the Side panel are also aligned with the fixtures on the wall See Fig 27 for details 22 Apply sealant to the entire surface of the reverse side of the other Side panel 01 See Fig 26 for details Slide the narrow edge of the other Side panel 01 behind the Corner cover 02 Align trimmed edge of the Side panel from Step 9 with the marked line on the wall in Step 7 and push the Side panel against the wall Align the top of both Side panels and the Back panel before the sealant sets Apply equal pressure to the whole surface of the Acrylic panels from top to bottom See Fig 28 for details Fig 27 N Fig 28 Ver 1 Rev 1 23 Once all panels are aligned fasten tight the Corner cover 02 to secure the Side panels 01 and Back panels 09 Cover the screw holes with the Decorative covers 08 See Fig 29 for details 24 Fasten tight the Center cover 10 to secure the Back panels 09 Cover the screw holes with the Decorative covers 08 See Fig 30 for details Fig 29
8. of the Back panel and continue scoring until you have fully cut through the panel See Fig 7 and Fig 8 for details 7 Li ANEEL E N Fig 8 WSS Ver 1 Rev 1 Preparation for Installation of Side Panels ATTENTION If you are installing a shower door with a wall profile you can hide the edge of the Side panel 01 behind the wall profile See Fig 9 for details 8 Measure the side walls of the shower from the 1 one inch line in the corner g from Step 1 to the distance where you want Side panels 01 to end The distance is D See Fig 10 for details 1 Side Panel Wall Profile Wall Wu xX 2 Side Panel Wall Profile Wall Fig 9 Ver 1 Rev 1 9 Determine the position of both Side panels 01 D D NOTE Line f sA Line a The narrow edge of the Side oa eeu panel fits behind the corner cover and cannot be trimmed b The wide edge of the Side panel can be trimmed to the size of your measurements from Step 8 Measure from the narrow edge of the Side panel and place a mark at a distance of D that you measured in Step 8 Draw a straight line from top to bottom along the wide edge of the Side panel
9. Installation Instruction at the center point along 3 the line from Step 3 and mark the z i lt JS drilling holes through the predrilled x holes in the Center cover Drill the holes using 5 16 drill bit and insert the Wall Anchors 06 See Fig 17 for details 5 16 Fig 17 15 Mount the Center cover 10 to the centerline of the 1 back wall using the Countersunk screws ST4 2x30 07 Do not fully tighten the screws at this time leave A them loose for further installation Xe See Fig 18 and Fig 19 for details Fig 18 Ver 1 Rev 1 16 Attach the Corner cover 02 to the corner of the shower and mark the drilling holes through the predrilled holes in the Corner cover Move aside the Corner cover Drill the holes using 5 16 drill bit and insert the Wall Anchors 06 See Fig 20 and Fig 21 for details Yo Va Fig 19 5 16 Fig 20 Ver 1 Rev 1 ATTENTION Installation of all Acrylic panels must be finished before the sealant sets for easy leveling and adjustments 17 Apply the sealant to the entire surface of the reverse side of the Back panel 09 See Fig 22 for details Mo Fig 21 Va
10. cs 02 Corner cover 2pcs 07 Countersunk screw ST4 2x30 21pcs 03 Decorative edge molding 2pcs 08 Decorative cover 15pcs 04 Shelf bracket 6pcs 09 Back panel 2pcs 05 Glass shelf 2pcs 10 Center cover 1pc NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference Before discarding the carton check for small hardware bags that tend to fall to the bottom of the box If any parts are damaged or missing please contact DreamLine for replacement NOTE Retain these installation instructions for future reference Ver 1 Rev 1 3 Preparation for Installation of Back Panel 1 Place a mark on the walls at a distance of 1 one inch from the corner and draw a plumb vertical line from top to bottom See Fig 1 for details NOTE Repeat this step for both corners 2 The Shower back wall kit has two Back Panels 09 Measure the back wall of the shower between the vertical lines you marked in Step 1 This distance is marked as W See Fig 2 for details Fig 1 Fig 2 Ver 1 Rev 1 3 Divide the measurement W by two and place a mark in the center of the back wall and from there draw a plumb vertical line from top to bottom This distance is shown as W 2 See Fig 3 for details
11. d Use only light pressure when cleaning Avoid rubbing dirt or grit into the surface Turn the cloth often and replace with a clean cloth frequently Dry by blotting gently with a clean dry cloth DO NOT USE Window cleaning sprays alcohol kitchen abrasive compounds or solvents such as acetone gasoline or thinners Do not use ammonia based cleaning solutions on the acrylic as it will eat into the surface and cause it to damage How do you get scratches out of Acrylic For light scratches use a buffing compound such as a car wax Use a buffer or lightly polish the surface by hand until scratches disappear TABLE OF CONTENTS Required Tools Torinstallaton corinds intros heunean Rue tieedatetstics Page 2 Detailed Diagram with Packing List c ce eeeeseeeeeeeseseseeeeeeeeeeeeeees Page 3 Preparation for installation of Back Panel 09 eee Pages 4 7 Preparation for installation of Side Panel 01 000 ee Pages 8 14 Back Panel and Side Panel Installation Instruction 0 0 0 Pages 14 19 Glass Shelf 05 Installation Instruction wo ccc cece eens Pages 20 21 Ver 1 Rev 1 22 EAMLINE dream in style TEL 866 731 8378 215 957 1411 FAX 866 227 9245 215 893 1780 WWW BATHAUTHORITY COM For more information on DreamLine Shower Back Wall please visit www BathAuthority com
12. duct has been installed Feel free to contact DreamLine if you have any questions Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project This acrylic wall system is specially designed to be installed over any solid surface If you are installing the acrylic walls over existing tiles remove all loose tiles before the installation If you are installing over existing painted walls remove any loose paint Please note that some cutting and drilling may be necessary during the installation process Make sure to turn off the water supply remove faucet handles or any fixture trims protruding from the wall Clean the surface removing any soap film and dirt from all wall surfaces using regular household detergent and then wipe dry Tools Required a Tape Drill bit T Square Caulk Measure Pencil Knife 5 16 q i Caulk ae N Phillips Level Gun Sa I Hammer Screwdriver Ver 1 Rev 1 Detailed Diagram of Acrylic Shower Wall Components 2 ts b 1 2 lt Ien Z g S9 So 3 62n 4 7 7 a 5 d 2 6 10 ri es 8 d 9 Packing List 01 Side panel 2pcs 06 Wall anchor 21p
Download Pdf Manuals
Related Search