American Woodmark VSDB6034HCBT40MJS.3213SN.TOP6222APLWI.DS Instructions / Assembly
Contents
1. UNPACK AND CARRY THIS VANITY TOP PROCEDURE 1 Use adamp cloth or vacuum to remove dust and dirt from top of the cabinet Allow surface to dry Apply a 1 4 inch bead of silicone along all parameter edges of the cabinet see fig 1 1 h v N fig 1 1 TIP Before using silicone make sure that the vanity top fits your cabinet If your vanity top does not have proper clearance do not force it on the cabinet 4 Carefully remove vanity top from box Stand vanity top upright with back edge facing down see fig 1 2 5 Carry the vanity top vertically to the cabinet fig 1 2 6 Carefully place the back edge of the vanity top approx 2 inches or as close to the wall as possible Lower the vanity top into place while carefully supporting the center of the vanity top As the vanity top is lowered carefully slide the vanity top back until it fits tightly against the wall see fig 1 3 TIP If there are any voids between top of cabinet and bottom of vanity top insert tapered shims as necessary Run a thin bead of clear silicone around perimeter of the vanity top to fill any visible voids between the cabinet and vanity top see fig 1 4 Remove excess silicone with a clean cloth BACKSPLASH INSTALLATION PROCEDURE 1 2 3 Prior to installation identify the face polished gloss surface and the top edge of the backsplash Apply masking tape along bottom edge of backspl2. DO IT YOURSELF VANITY TOP INSTALLATION GUIDE Woodmark DO IT YOURSELF VANITY TOP INSTALLATION GUIDE AMERICAN R SILESTONE Woodmark BEFORE YOU BEGIN IMPORTANT This guide contains important information to help you install and care for your DO NOT UNPACK VANITY TOP Silestone vanity top OR PROCEED ANY FURTHER WITHOUT READING THE FOLLOWING INSTRUCTIONS Please read these instructions thoroughly before starting your installation SUPPLIES REQUIRED YOU MAY NEED ONE OR MORE OF THE FOLLOWING Color matched or clear silicone caulk Tapered shim material Clean white cotton cloth Pencil Masking tape Denatured alcohol TOOLS YOU MAY NEED ONE OR MORE OF THE FOLLOWING mM Caulking gun mM Jape measure EH Utility knife mM Vacuum optional VANITY TOP INSPECTION 1 Without lifting the vanity top visually inspect the surface for obvious shipping or material damage 2 Inthe event of damage immediately report any problems to customer service before proceeding any further Claims filed more than 15 days after receipt of product will not be honored Contact customer service at 855 HD4VANS or via e mail at customercare americanwoodmark com CABINET PREPARATION 1 Inspect installation area to make sure cabinetry is properly secured and stable 2 Cabinet surface must be flat and level prior to installation of the vanity top STOP IMPORTANT LIFTING INSTRUCTIONS TWO PEOPLE ARE REGUIRED TO
3. ash and along the back edge of the vanity top see fig 2 1 The tape needs to be set away from the back edge of the top for the thickness of the splash 1 8 inches this will aid in the removal of excess silicone fig 2 1 Apply a bead of color matched or clear silicone caulk along the bottom edge of the backsplash see fig 2 2 fig 2 2 Apply dabs of silicone to the backside of the backsplash see fig 2 3 fig 2 3 4 Carefully set backsplash into place against wall and vanity top Be sure to lightly press backsplash into place Do not use excessive force see fig 2 4 fig 2 4 Apply a thin bead of color matched or clear silicone along the joint between the backsplash and the vanity top Smooth the silicone bead with a clean white cotton cloth dampened with a denatured alcohol Remove masking tape from backsplash and vanity top Repeat steps 1 7 to attach side splashes if applicable Wait 24 hours before using vanity top to allow time for silicone to fully cure Note Follow all manufacturer s instructions and safety information on all silicone caulk containers Ensure adequate ventilation before applying silicone
Download Pdf Manuals
Related Search