Vigo VG6063CHCL42W Installation Guide
Contents
1. GLASS SUPPORT 6 4 DE GLASS PANEL Is GASKET pork VIEW FROM THE TOP FIG 4 C HANDLE INSTALLATION 1 Assemble the door handles 11 to the door 12 SEE FIG 5 GASKETS HINGE INSTALLATION Clean the glass surface on the side glass panel 44 where the hinges 7 are to be installed with rubbing alcohol Position hinges on the side glass panel SEE FIG 6 Place washers on each side of the side glass panel Screw the hinges to the side glass panel with the hex key supplied 7792 m SCREW THIS HALF OF THE HINGE HINGE LOOKS OUTSIDE OF T THIS SIDE OF TI TO VIEW FROM INSIDE OF THE CABIN CABIN SCREW THIS H THE HINGE TO GLASS PANEL VIEW FROM OUTSIDE OF THE CABIN MODEL VG06063 ALF OF THE SIDE http www vigoindustries com INSTALLING THE WATER SEAL STRIP IEBSA Clean the side glass panel 4 edges where the door side seal strip 13 and the door bottom seal strip 14 are to be installed with rubbing alcohol Cut the seal strips according to the diagram SEE FIG 7 Verifv that the lips of both seal strips face toward the inside of the shower cabin before seal strip installation Install the seal strips according to the diagram THIS SIDE MUST LOOK INSIDE THE CABIN THIS SIDE MUST LOOK INSIDE THE CABIN FIG 7 SEAL STRIP INSTALLATION MODEL VG06063 http www vigoindustries com 1 866 591 7792 WARNING DOOR PANEL INSTALLATION RE2. Seal the bottom rail with clear silicone caulk and center its sides to the base Apply silicone to the 3 4 screw 15 threads SEE FIG 2A Screw the bottom rail to the base with the screws Clip the aluminum cover to the front piece of the bottom rail MODEL VG06063 http www vigoindustries com 1 866 591 7792 THIS EDGE LOOKS INSIDE OF THE SHOWER gt TOP REMOVES TO Er INSTALL 3 4 SCREW l THIS EDGE LOOKS gt OUTSIDE OF THE SHOWER INSTALLING SIDE GLASS PANEL Arrange glass to the preferred configuration see diagram on page 3 Select the door opening location on the shower cabin Install the side seal strip 5 to the wall side of the hinged side glass panel 4 SEE FIG 3 Screw in the glass support 6 to the side glass panel using the hex key supplied Be sure to use washers on both sides of the panel Place the side glass panel onto the bottom rail 8 Use the level to position the side glass panel correctly Mark holes on the wall for the mounting screws Remove the side glass panel Drill holes into respective marks and insert plastic anchors 19 inside them Replace the front glass panel back onto the bottom rail and screw it to the wall with 1 5 8 screws 16 Repeat steps 1 through 8 for the unhinged side glass panel 4 SEE FIG 4 THIN GASKETS WALL SIDE DOOR SIDE FIG 3 MODEL VG06063 http www vigoindustries com 1 866 591 HEX SCREW 16 HEX SCREW
3. distributor authorized VIGO dealer nor any other person has been authorized to make any affirmation representation or warranty other than those contained in this warranty Any affirmation representation or warranty other than those contained in this warranty shall not be enforceable against VIGO or any other person VIGO reserves the right to modify this warranty at any time it being understood that such modifications will not alter the warranty conditions applicable at the time of sale of the products in question Limitations This warranty shall not apply to instances of incorrect operating procedures breakages or damages caused by fault through improper installation carelessness abuse misuse misapplication improper maintenance or alteration of the Product as well as chemical or natural corrosion accident fire flood an act of God or any other casualty Avoid abrasive cleaners steel wools and harsh chemicals as these will scratch damage and or dull the product and or finish and void this warranty The owner end user of the Product covered by the present warranty is entirely responsible for its proper installation and any applicable plumbing or electrical wiring VIGO neither installs nor supervises the installation nor hires a contractor for this purpose consequently VIGO cannot be held responsible for any default breakage or damages caused thereby or resulting thereof either directly or indirectly The owner end user must
4. provide access to the components of the Product as described in the installation guide so that VIGO can execute the warranty specified herein If such access is not available all expenses to provide said access will be the responsibility of the owner end user This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied by VIGO and all applicable rules regulations and legislation pertaining to such installations This warranty does not apply unless the VIGO Product is installed by fully insured licensed professionals Vigo strongly recommends that such licensed professionals have experience in the installation of bathroom and kitchen products Installation of certain products including without limitation glass products i e shower doors and glass sinks by an inexperienced person may result in glass breakage and consequently cause personal injury or death VIGO is not liable for personal injuries or deaths to any persons or for any direct special incidental or consequential damage loss of time loss of profits inconvenience incidental expenses labor or material charges or any other costs resulting from the use of the product or equipment or pertaining to the application of the present warranty or resulting from the removal or replacement of any product or element or part covered by this warranty EXCEPT AS OTHERWISE PROVIDED ABOVE VIGO MAKES NO WARRANTIES EXPRESSED
5. 1pc is extra 14 Door bottom seal strip 2pc 1pc is extra 15 Hex screws 1 1 8 4pc 16 Hex screws 1 5 8 8pc 17 Phillips screws 3 4 8pc 18 Plastic anchors green 12pc 19 Plastic anchors white 8pc 20 Hex screw covers 32pc GLASS THICKNESS 3 8 NOTE INSTALLATION MUST BE DONE BY A QUALIFIED LICENSED PROFESSIONAL MODEL VG06063 http www vigoindustries com 1 866 591 7792 1 WALL CONNECTOR 98001 2 STRUCTURAL ARM 98002 42 98002 47 3 SUPPORT ASSEMBLY 98003 D Eg 4 SIDE PANEL 97001 42 97001 47 5 SIDE SEAL STRIP 96001 6 GLASS SUPPORT 98004 7 HINGE ASSEMBLY 98015 IS 8 BOTTOM RAIL 95001 42 95001 47 gt 9 MAGNETIC SEAL STRIP 96002 el 10 CORNER JOINT 94001 amp 11 DOOR HANDLE ASSEMBLY O 12 DOOR 13 DOOR SIDE SEAL STRIP 96003 14 DOOR BOTTOM SEAL STRIP 96004 15 HEX SCREW 1 1 8 16 HEX SCREW 1 5 8 97002 12 17 PHILLIPS SCREW 3 4 98033 I 18 PLASTIC ANCHOR 98037 0 19 PLASTIC ANCHOR 98038 gt 20 HEX SCREW COVER J 96040 MODEL DIMENSION A DIM B DIM C HEIGHT 4 SIDE GLASS 12 DOOR PANEL 97001 97002 42x42 21 1 8 26 7 8 73 1 3 20 1 2 x71 5 8 12 5 8 x70 3 4 47x47 45 5 8 26 5 8 26 7 8 26 x71 5 8 i WITH HARDWARE AND WITHOUT SHOWER BASE SE EXTERIOR SIZES A B amp C DIMENSIONS WERE MEASURE
6. D AFTER SHOWER ENCLOSURE WAS COMPLETELY INSTALLED MODEL VG06063 12 5 8 x70 3 4 http www vigoindustries com 1 866 591 7792 N WARNING WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER CABIN AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS BREAKAGE AND CONSEQUENTLY CAUSE PERSONAL INJURY OR DEATH BEFORE STARTING Compare items on your invoice with what you have received Carefully review the Packing List on page 2 If any items are missing contact Vigo Industries at 1 866 591 7792 REQUIRED TOOLS Square and or Phillips 1 and 2 screwdriver Flat head screwdriver Electric drill plus 1 8 3 16 or 7 32 drill bit depending on wall Level Measuring tape Pencil non permanent HB Clear silicone caulking Utility knife WARNING Handle fragile items with care to prevent injury or material damage Glass on panels and doors is tempered glass and must never be cut to prevent personal injury SO IMPORTANT Fiberglass or acrylic construction might not be sufficiently strong enough to support the shower door enclosure You should use the wood framing from behind the face edge of the stall to provide a secure mounting to the door Apply a bead of silicone between the walls and base of the stall e For optimum performance vou should install the shower door perfectiv level on a level
7. OR IMPLIED INCLUDING WARRANTIES OF ERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR COMPLIANCE WITH ANY CODE n any case VIGO cannot be held liable for any amount over and above the purchase price paid for the Product by the owner end user contractor or builder Commercial Limitations n addition to the above conditions and limitations the warranty period for products installed for commercial applications or used in commercial ventures iS one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer VIGO is not responsible for loss of use or profit under any circumstances If the product is used as a display the warranty period begins when the product is placed on display This warranty gives the owner end user specific legal rights The owner end user may also have other rights which can vary from one state or province to another Warranty Service In order to obtain service provided under this warranty during regular business hours contact the dealer or distributor who sold the unit or contact VIGO directly VIGO will provide the warranty service described above when the following conditions have been met the failure is of the nature or type covered by the warranty the user has informed an authorized VIGO Agent or VIGO s warranty service department representative of the nature of the problem during the warranty period conclusive evidence e g proof of purc
8. QUIRES TWO OR MORE PEOPLE TO ASSIST F INSTALLING THE DOOR Clean the door 12 glass surfaces where the hinges 7 are to be installed with rubbing alcohol Position the door onto the hinges Hold securely in place Place a thin gasket supplied on each side of the door between the glass and hinge while holding the door in place Install the hinges as illustrated SEE FIG 8 Use the hex key supplied fe OUTSIDE OF N HINGE 7 if THE CABIN SIDE jf N GLASS PANEL 4 DOOR 12 A D m NSIDEOF GASKETS THE CABIN HEX SCREW VIEW FROM VIEW FROM THE TOP INSIDE FIG 8 INSTALLING THE SIDE amp FRONT PANEL SUPPORT Install the support assembly 3 onto the side glass panel 4 approximately two thirds away from the wall Use hex key to tighten to screws SEE FIG 9 Install the support assembly to the structural arm 2 and wall connector 1 Mark the holes on the wall for the mounting screws Remove the support assembly Drill holes into respective marks and put plastic anchors 18 in them Replace wall connector to proper position Screw it in to the wall with 1 1 8 screws 15 Tighten all screws Repeat Steps 1 through 6 to install the other support assembly to the other side glass panel MODEL VG06063 htto Awww vigoindustries com 1 866 591 7792 APPLYING THE SILICONE Apply clear silicone caulking to the inside between the wall and side seal strip Apply clear silicone caulk to the insi
9. VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE MODEL VG06063 SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information Always observe the instructions indicated by these symbols A WARNING Instructions that if ignored could result in death or serious personal injury caused by incorrect handling or installation of the product These instructions must be observed for safe installation CAUTION The instructions for the following unit is based off of the Vigo brand shower base The instructions can not be provided for any other installation other than that of the Vigo brand The warranty will be voided if the following was not performed properly NO IMPORTANT Maintenance and other important non personal injurv and non material damage instructions or statements that should be observed It is highly advised to dry fit the unit prior to any installation http www vigoindustries com INSTALLATION INSTRUCTIONS FOR STANDING SHOWER CABIN 1 866 591 7792 OWNER S MANUAL PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Packing List Wall connector 2pc Structural arm 2pc Support assembly 2pc Side glass panel with hinge slots 2pc Side seal strip 2pc Glass support 4pc Hinge 4pc Bottom rail 3 pc Door magnetic seal strip 2pc 10 Bottom corner joint 2 pc 11 Handle assembly 2 sets 12 Door 2 pc 13 Door side seal strip 2pc
10. de between the bottom of side glass panels 4 5 and bottom rail Apply clear silicone caulk around the inside perimeter of the bottom rail SEE FIG 10 INSTALLING HEX SCREW COVERS Install hex screw covers 20 to the hex screws that mount the hinges wall connectors and glass supports M IMPORTANT e WAIT 24 HOURS BEFORE USING SHOWER e DO NOT ALLOW WATER TO DIRECTLY HIT DOOR SEAL STRIPS MODEL VG06063 htto Awww vigoindustries com 1 866 591 7792 CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL A B C D Use mild liquid household cleaners to keep metal surface bright and clean Rinse well and drv with a clean cloth Remove dust with a soft damp cloth Use rubbing alcohol to clean and remove grease oil paint and ink Accidental scratches or stains will rarely show If they do show they can be easily removed with a liquid automobile polish AM IMPORTANT Do NOT use abrasive cleaners scrapers metal brushes or any items products that would scratch and or dull surface Do NOT allow surface to come into contact with acetone nail polish remover dry cleaning solution lacquer thinner gasoline or any other similar product MODEL VG06063 http www vigoindustries com 1 866 591 7792 VIGO INDUSTRIES LLC VIGO SHOWER ENCLOSURE LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1 2010 VIGO offers the following limited warranty on each of its Shower Enclosure
11. hase or installation is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period an authorized independent service person or company representative has been permitted to inspect the product during regular business hours within a reasonable time after the problem was reported by the user VIGOs warranty obligation shall be discharged upon tender of replacement or repair The customer s refusal to accept the tender terminates VIGO s warranty obligations Certain models are pending approval Certification may be ended by VIGO or certification agencies without notice MODEL VG06063
12. products the Product and the components thereof This warranty extends only to the original owner or end user for personal household use For commercial uses additional limitations apply VIGO warrants the structural glass component of the Product to be free from defects in workmanship and materials under normal use and service for the period commencing from the initial date of purchase by the owner or end user contractor or builder from VIGO or an authorized VIGO dealer through the lifetime of the original owner or end user VIGO warrants the hardware components of the Product to be free from defects in workmanship and materials under normal use and service for a period of two 2 years from the initial date of purchase by the owner or end user contractor or builder from VIGO or an authorized VIGO dealer VIGO warrants the seal strip components of the Product to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the initial date of purchase by the owner or end user contractor or builder from VIGO or an authorized VIGO dealer Subject to the Warranty Service provision below any product reported to the authorized dealer or to VIGO as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of VIGO This warranty extends to the original owner or end user and is not transferable to a subsequent owner Neither the
13. surface IMPORTANT THE CLEAR GLASS MODEL HAS A REVERSIBLE DOOR AND CAN BE INSTALLED TO THE RIGHT OR LEFT SIDE THE TEXTURED SIDE OF THE MATTE GLASS UNIT SHOULD ALWAVS BE INSTALLED ON THE OUTSIDE OF THE UNIT SEE CONFIGURATION DIAGRAM BELOW FRONT GLASS DOORPANELS SIDE GLASS PANEL PANEL FIG 1A GLASS CONFIGURATION DIAGRAM MODEL VG06063 http www vigoindustries com 1 866 591 7792 PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION Remove the plastic layer from the base border if needed Do NOT remove the plastic layer off the plastic platform of the base Properly apply silicone to the wall and base joints 5 IMPORTANT To prevent damage to the finish you should protect the shower cabin bottom with a cardboard protector before beginning the installation Ensure that there is sufficient structural support behind the shower wall to hold the weight of the shower door If there is insufficient enough support then reinforce the shower walls with wooden studs prior to shower door installation SEE FIG 1 INSTALLATION STEPS A INSTALLING THE BOTTOM RAIL CAUTION TO ALLEVIATE WATER BUILD UP IN THE TOP PORTION OF THE RAIL IT IS RECOMMENDED TO DRILL SMALL HOLES ON THE TOP INSIDE PORTION Slide the bottom corner joint 10 onto the bottom rail 8 SEE FIG 2 Align the bottom rail and corner joint to the desired position on the shower base Make sure the the A and B distances are correct see page 3 for A and B distances
Download Pdf Manuals
Related Search