Symmons SLS-4312 Instructions / Assembly
Contents
1. 3 8 compression fitting amp stopper P 100N pop up drain assembly P 25LR includes stopper Symmons Industries Inc 31 Brooks Drive Braintree MA 02184 800 796 6667 781 848 2250 Fax 800 961 9621 781 843 3849 Website www symmons com Email customerservice symmons com S M M O N S 2008 Symmons Industries Inc Printed in U S A ZV 574 0516082. faucet handle to the OFF position and then turn water supply valves ON and outer seat from pivot cavity Insert pivot rod into pivot cavity so ball is against inner seat and rod passes under stopper according to selected eye hole position Step 3 Fasten drain body to sink x pivot rod retaining nut Wa outer seat pivot ball inner seat pivot cavity Remove stopper unscrew flange and remove washer from end of drain body as shipped PLUMBERS PUTTY Apply plumber s putty around bottom of flange Note Washer included should only be used when plumbers putty is not available Insert outer seat over pivot rod with curved edge against pivot ball Fasten pivot rod to drain body with retaining nut Tighten until ball is seated snug and pivot rod can move freely Step 6 Connect lift rod and adjust linkage a Move friction washer beveled washer and flange nut down away from end of drain body Insert lift rod through hole on rear of water spout washer optional Fasten end of pivot rod with spring clip through location hole in clevis strap that is best aligned to enable lift rod also Page 2 fasten to clevis strap when in the up position and stopper is in the closed position Insert lift rod into end of clevis strap and fasten with thumb screw at location where stopper can be easily opened and closed If necessary select another loc
3. p icti auce washer and friction body cavity Insert faucet washer up against sink bolts and flex gasket Tighten flange nut up hoses through wacher against friction washer to evenly compress beveled washer center of base and anie while also ensuring flange is centered in drain opening mounting hole aer host Take care not to over tighten flange nut Slide gasket and ape Step 4 Install stopper and set eye position washer over bolts under sink and Stopper can be installed fasten with hex nuts to be ae i stopper Center faucet in sink mounting hole and tighten hex nuts iene alae flange 8 8 determined by osition of eye hole non Step 2 Connect water supply lines 4 hon tie ramavable removable Plumb hot water supply pivot rod to flex hose supply inlet ee on left identified with B 0u 4 through flange Yy a red marker and cold wine ie oe gt water to right hose iti al identified with green pes un pa or blue marker flex hose Removing stopper supply inlets When set in removable position move pivot rod to the up Fasten to 3 8 inch hotad position lift rod will be in the down position when later ond of flex h fitting a installed Eye hole will slide over end of pivot rod end of flex hose supply inlet and tighten cold green Step 5 Attach pivot rod to drain body Check for leaks if only Remove retaining nut replacing faucet and drain is already installed by first turning
4. SYMMONS Sereno Lavatory Faucet SLS 4312 Installation and Service Instructions Model Numbers Tools amp Materials amp Need Help SLS 4312 aaan Chrome finish Contact Symmons customer service at SLS 4312 STN Satin Nickel finish Xe 800 796 6667 781 848 2250 Email customerservice symmons com Monday Friday 8 00 am 7 30 pm EST PUTTY Please check Symmons website for technical help the latest product information and warranty policy www symmons com service PLUMBERS Attach faucet to sink or deck Connect water supply lines Dao Non Removable Removable stopper stopper Step 4 d Flush water supply lines Install stopper and SN set eye position NSS Connect lift rod clevis strap pivot rod and adjust linkage Fasten drain body to sink Attach drain body to drain trap e Attach pivot rod to drain body Installation Instructions Caution If replacing an older faucet ensure water supply is turned OFF before removing Then open faucet valves to relieve water pressure Place flange in drain opening and under sink screw drain body up into flange Step 1 Attach faucet to sink at least 2 3 turns flange Screw short until hand tight beveled threaded end of Position drain body 7 washer mounting bolt so pivot cavity is friction into bottom of facing rear of sink flange nut washer faucet a stop and then slide beveled dan Sool is reached f
5. ation al lift rod lift rod stopper thumb screw clevis strap location hole spring clip Care of faucet finish Clean finish area by using mild soap and water or non abrasive cleaners and then rinse immediately A non abrasive wax may be used to preserve finish area Valve cartridge replacement Step 1 Remove handle Pry out small plug button Loosen set screw using a 2 5 mm Allen wrench Step 2 Remove collar Rotate counter clockwise handle A set screw plug button o collar fastener ____ hole in clevis strap and re adjust lift rod where fastened to clevis strap Step 7 Attach drain body to drain trap Step 8 Flush water supply lines Thoroughly flush supply lines to prevent foreign matter i e copper chips sand etc from damaging the control valves Remove Remove aerator from end aerator of faucet water spout Move faucet handle to full ON position open water supply valves and run long enough to flush supply lines thoroughly Turn faucet OFF replace aerator and check for any leaks Note Ensure not to use any tool that could scratch finish without taking protective measures cartridge ee dosition keys Step 3 Remove fastener Rotate counter clockwise using faucet an adjustable wrench Step 4 Lift out cartridge Step 5 Slide replacement cartridge into faucet When sliding into faucet align and seat positio
6. n keys on bottom of cartridge into location holes in base of faucet Step 6 Re attach fastener and collar Step 7 Attach handle Place handle onto top of cartridge ensuring handle is pointed toward center of sink Tighten set screw using 2 5 mm Allen wrench and then press plug button back into screw hole Dimensions Sereno Lavatory Faucet SLS 4312 ha Ae 125 mm 7 3 4 196 mm 6 1 2 166 mm 4 a l 2 50 mm 30 degrees gt a a er Se Deck thickness t 1 3 8 35 mm max Note Dimensions subject to change without notice OOOX AAV XX Cor re LAA O EEA 2 3 8 60 mn XXX xX XX Hole size ere 1 3 8 85 mm min 1 5 8 41 mm max QO Parts Assembly Sereno Lavatory Faucet SLS 4312 handle ____ Faucet Handle reference table Part Number ed LN 315 handle Se SF set screw g lift rod button plug 8 LN 341 Set screw requires 2 5 mm Allen wrench Valve cartridge _ _ reference table valve cartridge Note For decorative finish faucets append the aerator ___ appropriate suffix code letters to part numbers LN 342 marked with an asterisk Ordering replacement parts Call Symmons customer service at 800 796 6667 781 848 2250 M F 8 00 am 7 30 pm EST or flex hose check our website at www symmons com fora 20 length list of Symmons distributors
Download Pdf Manuals
Related Search