DreamLine DL-6433L-01CL Installation Guide
Contents
1. DREAMLINE JETTED AND STEAM SHOWER CABINS DREAMLINE SHOWER COLUMNS AND DREAMLINE SHOWER SEATS ARE NOT INTENDED FOR COMMERCIAL USE AND THERE IS NO WARRANTY EXTENDED FOR THESE PRODUCTS FOR COMMERCIAL USE DreamLine hereby disclaims all warranties for products sold as dealer or store displays DreamLine hereby disclaims all warranties for products used outside of the United States or Canada whether expressed or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose WARRANTY TERMS DreamLine will at its election repair or replace the product found by DreamLine in its sole judgment to be defective within the warranty period under normal residential use and maintenance The replacement of a product is limited to supplying a replacement product or part same as existing or if not available comparable product DreamLine warranty obligation shall be discharged upon tender of parts replacement or repair of the product Purchaser s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY Cost of freight for returning products to DreamLine for repairs or replacement under this limited warranty are the responsibility of the customer Cost of freight associated with shipping of replacement product or parts to the customer may be charged to customer Any product replaced or repaired during the warranty period will be covered only for the remaining period of the original warr2. Drain 2 PVC Waste Pipe SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 11 Shower Base Installation Preparation 1 Ensure that the floor and the studs are at right angle Provide a 5 x5 opening in the sub floor for the drain The 2 PVC waste pipe should extend above the surface of the sub floor according to the drain installation instructions and the height of the Shower base Refer to the product drawings in these installation instructions for the drain location See Fig 1 and Fig 2 for details SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 2 PVC Waste Pipe 5 5 Opening See Product Chart for Drain Location Fig 1 x 2 PVC Waste Pipe 5 x5 Opening See Product Chart for Drain Location Fig 2 12 2 Install the shower drain NOT PROVIDED according to the drain installation manual supplied with the drain See Fig 3 for details 3 Place the tray into the designated position so that the Drain Body drops around the Drain Pipe and butt the Shower Base up against the studs See Fig 4 for details Lift and lower base over the center of The drain pipe and set it into the place Fig 4 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 13 4 Level the tray and place marks on the studs above the upper edge of the tile flange See Fig 5 for details Level base in two directions Fig 5 5 Mix the bedding material Mortar Plaster etc Concrete is
3. DreamLine warrants bathroom vanities and vessel sinks to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer STATE LAWS AND THIS WARRANTY Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of special incidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state province to state province WARRANTY SERVICE The following information will be required for you to file a Warranty claim 1 Your name address and telephone number 2 Product model number 3 Brief description of problem please note that additional information such a photos may be required to fully process your warranty claim 4 Proof of purchase You may submit this information by e mail mail or fax to DreamLine Warranty Service Center 75 Hawk Road Warminster PA 18974 F 1 866 857 3638 T 1 866 731 2244 Warranty bathauthority com dream in style TEL 866 31 2244 FAX 866 227 1533 WWW BATHAUTHORITY COM For more information on DreamLine Shower Doors please visit www BathAuthority com
4. OREAMLINE ream in style Allure Shower Door amp Base Kit SHOWER Door AND SHOWER BASE KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page STEP 1 Install Shower Base Shower Base Installation Instructions STEP 2 Install Shower Door Shower Door Installation Instruction Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Kit please visit www BathAuthority com ream in style ALLURE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone
5. Glass door by loosen the holding screws on the pivots Level the Glass door and the Stationary glass position to ensure the Magnetic strips are able to contact each other properly See Fig 14 for details Fig 14 15 Draw a line along the vertical edge of the Wall profile 06 on the wall Detach the Wall profile from the Glass profile 05 Place the Wall profile to the outlined position and mark the drilling holes through the predrilled holes in the Wall profile Now drill the holes using 5 16 drill bit in the wall and insert the Wall anchors 15 into the holes Apply silicone along the Wall profile and around the holes Fasten the Wall profile to the wall with the Round head Screw ST4 2x40 18 See Fig 15 for details Fig 15 Allure Rev 3 Ver 1 04 2013 12 16 Slide the Stationary glass 04 with the Glass profile 05 back into the groove of the Wall profile 06 Readjust the Glass door 04 to ensure that Magnetic strips 33 work as desired See Fig 16 for details 17 Install the Bracket 32 onto the stationary glass and drill the hole into the Shower base or the threshold using O 1 8 drill bit e 2 Use Round head screws ST4 2x25 30 to i attach the Bracket to the Shower base or the threshold SS Cover the screw location with Decorative __ cover 31 Sa ay See Fig 17 for details Fig 17 Allu
6. SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Bases please visit www BathAuthority com Preparation 1 Examine boxes and packages for shipping damage Carefully remove Shower base from the packaging and check for any visual defects or shipping damages If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed Feel free to contact DreamLine if you have any questions Install all of the required plumbing and drainage before installing the shower Use a competent and licensed if required by local code plumber for all plumbing installation Please note t
7. for small stationary glass Fixing nut with M4x12 screw Glass profile for small stationary glass Smal stationary gas Glas prof 06 Wall proi Handle 08 Pivot retainer pes 20 Decostvecoer LO _ Pivot bracket Cupper and bottom 177 Bottom antrwater stip HIS Gasser upper and bottom 1 2 Hex wrench Packing List B Only for door with stationary glass Stationary glass Round head screw ST4 2x25 Self bracket Shelf bracket with nu rapes 3 Bracket Wall anchor Flat head screw ST4 2x25 Glass shelf NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using parts diagram and part list in your manual as a reference Before discarding the carton check for small hardware bags that tend to fall to the bottom of the box If any parts are damaged or missing please contact DreamLine for replacement NOTE Retain these installation instructions for future reference Allure Rev 3 Ver 1 04 2013 Shower Door Top View Diagram Allure Rev 3 Ver 1 04 2013 Shower Door Installation 1 Place the Wall profile for small stationary glass 01 on the threshold vertically and align against the finished wall Adjust the Wall profile for small stationary glass position and level it Mark the drilling holes on the wall through the predrilled holes in the Wall profile for small stationary glass Now drill the holes in the wall using 5 16 drill bit and insert
8. 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Doors please visit www BathAuthority com Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Shower Door Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed Feel free to contact DreamLine if you have any questions 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project and will not accept any returns 3 If this unit is going to be installed in a new construction please install all of the required plumbing and drainage before installing the shower Use a competent and licensed if required by local code plumber for all plumbing installation 4 Prior to the installation please ensure that the installation surface is level a
9. 34 x 60 34 60 DLT 1136601 36 x60 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 Right Hand Drain Configuration WI D1 MODEL SPECIFICATION D1 in W1 in 30 x 60 mo ox ow ode oam omaa 3460 1 36 ix _ SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 NEO SHOWER BASE 01722036360 36736 18 5 16 DLT 2088380 38538 38 20916 m DLT 2040400 La 40 22 5 16 14 3 8 DLT 2042420 arxar a SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 QUARTER ROUND SHOWER BASE DLT 7033330 33 x33 21 5 8 DLT 7036360 36 36 21 5 8 DLT 7038380 38 x 38 21 5 8 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration MODEL SPECIFICATION W in C in DLT 1032320 3232 DLT 1036360 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 Left Hand Drain Configuration WI D1 MODEL SPECIFICATION D1 in W1 in DLTA0M4B 3448 ir iX DLT 1036481 36 x48 DLT 1036601 36 x60 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 Right Hand Drain Configuration WI D1 DLT 1034482 34 x48 MODEL SPECIFICATION D1 in W1 in 6 DLT 1036482 36 x48 DLT 1036602 36 x60 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 10 Diagram of the Shower Base in a Cross Section Finished Wall board Shower Base OOOO Mortar Plaster 2 x4 Stud
10. allation This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada Proof of purchase original sales receipt from the original consumer purchase must be provided with all warranty claims IN NO EVENT SHALL THE LIABILITY OF DREAMLINE EXCEED THE PURCHASE PRICE OF THE UNIT DreamLine products must be installed by a fully insured and licensed professional Installation of DreamLine product by anyone other than fully insured licensed professionals shall VOID THE WARRANTY DreamLine recommends that such licensed professionals have experience in the installation of bathroom products Installation of certain products including without limitation glass products i e shower and tub doors by an inexperienced installer may result in glass breakage and consequently cause personal injury or death PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects LABOR CHARGES AND OR DAMAGE INCURRED IN INSTALLATION REPAIR OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR DAMAGE ARE EXCLUDED COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial commercial and business usage whose purchasers are hereby extended a one 1 year limited warranty from the date of purchase for shower and tub doors a three 3 month limited warranty from the date of purchase for vanities and sinks with all other terms of this warranty applying except the duration of the warranty
11. anty In no event will DreamLine be liable for costs of repair or replacement of any installation material including but not limited to tiles marble etc DREAMLINE IS NOT RESPONSIBLE FOR INSTALLATION REMOVAL OR REINSTALLATION COSTS OF ANY PRODUCT REQUIRING WARRANTY SERVICES Any modification or alteration of any DreamLine products will void the warranty DreamLine product installations and repairs must be performed by either a DreamLine authorized agent or a licensed insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty This warranty shall not apply to breakage or damages caused by normal wear and tear fault carelessness abuse misuse misapplication improper maintenance alteration or modification of the unit as well as chemical or natural corrosion accident fire flood act of God or any other casualty Improper care and cleaning will void the warranty Use of cleaners containing abrasive cleansers ammonia bleach acids waxes alcohol solvents or other products not recommended for chrome or similar finish glass or acrylic will void the warranty For additional product maintenance instructions please refer to product installation manual DreamLine is not responsible for any issues arising in connection with errors or omissions in information provided on DreamLine s websites The warranty does not extend to any non DreamLine plumbing or components installed by installers en
12. ary glass you only need to refer to Diagram A with Packing List A and follow to Steps 10 13 b If the width of your door is 3714 and over and you are installing the door and stationary glass with glass shelves you have to use Diagram A and B with Packing List A and B to complete the installation and follow to Steps 14 21 Allure Rev 3 Ver 1 04 2013 9 10 Push the Glass profile 05 into the groove of the Wall profile 06 and push the Magnetic strip on jamb 24 into the groove of the Glass profile Close the Glass door 04 Adjust the position of the Glass door and position of the Wall profile on the wall to ensure the Magnetic strips are able to contact each other properly In this process you have to use a level to ensure that the Glass door is absolutely vertical Draw a line along the vertical edge of the Wall profile on the wall Detach the Wall profile from the Glass profile Place the Wall profile to the outlined position and mark the drilling holes through the predrilled holes in the Wall profile Now drill the holes using 5 16 drill bit in the wall and insert the Wall anchors 15 into the holes Apply silicone along the Wall profile and around the holes Fasten the Wall profile to the wall with the Round head Screw ST4 2x40 18 Then push the Glass profile assembly into the Wall profile See Fig 10 for details 11 After final adjustments of the Assembled unit drill six holes three on each sid
13. d users or by any party other than DreamLine THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE BATH AUTHORITY LLC DREAMLINE AND OR SELLER DISCLAIMS ALL LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES DREAMLINE IS NOT LIABLE FOR PERSONAL INJURIES OR DEATH TO ANY PERSON OR FOR ANY DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGE LOSS OF USE LOSS OF TIME LOSS OF PROFITS INCONVENIENCE INCIDENTAL EXPENSES LABOR OR MATERIAL CHARGES OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY OR RESULTING FROM THE REMOVAL OR REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY PRODUCT WARRANTY PERIODS DreamLine is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is excluded from this warranty DreamLine reserves the right to modify this warranty at any time such warranty modifications will not alter the warranty applicable at the time of sale of the products in question The warranty terms for specific products for consumer non industrial non commercial non business use only are SHOWER BACKWALL SHOWER CABINS JETTED amp STEAM DreamLine warrants shower backwalls and shower cabins to be free from defects in workmanship for a period
14. e through the first layer of the Wall profiles and the Glass profiles using O 1 8 drill bit Use Flat head screws ST4 2x10 16 to secure the Glass profiles inside of the Wall profiles Cover the exposed screw holes with Decorative cover 20 See Fig 11 for details Fig 11 Allure Rev 3 Ver 1 04 2013 10 12 Mount the Handle 07 onto the Glass door O1 Attach the Bottom anti water strip 21 onto the glass door You can cut the strip to size by using a knife See Fig 12 for details Fig 12 13 Apply silicone sealant between the tray or threshold and the pivot bracket Also apply silicone between the wall and the wall profiles See Fig 13 for details Silicone Allure Rev 3 Ver 1 04 2013 Stationary Glass Installation 14 Push the Magnetic strip 33 on the vertical edge of the Glass door 04 Apply clear silicone along the inner channel of the Glass profile 05 and push the Stationary glass 25 inside the channel NOTE If you have difficulty sliding the Glass profile over the Stationary glass you can slightly tap on the Glass profile with a rubber mallet and a piece of wood Please do not strike directly on the profile or on the edge of the glass panel Slide the Stationary glass with the Glass profile into the groove of the Wall profile 06 Push the Magnetic strip 33 on the vertical edge of the Stationary glass Close the Glass door Adjust the width of the opening section of the
15. er direction for the door opening you need only to exchange the position of the pivot assembly 12 See Fig 22 amp Fig 23 Fig 23 Allure Rev 3 Ver 1 04 2013 16 Maintenance To insure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To insure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup Never use abrasive cleaners and cleaning products that contain scoring agent because this may scratch the surface Never use bristle brushes or abrasive sponges To assure a long lasting finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the surface as soon as possible to prevent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week When applying stainless steel cleaner or polish work with not across the grain Never use abrasive sponge or cloth steel wool or wired brushes Allure Rev 3 Ver 1 04 2013 17 lt BREAMLINE ream in style SLIMLINE
16. er each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To insure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup Never use abrasive cleaners and cleaning products that contain scoring agent because this may scratch the surface Never use bristle brushes or abrasive sponges To assure a long lasting finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the surface as soon as possible to prevent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week When applying stainless steel cleaner or polish work with not across the grain Never use abrasive sponge or cloth steel wool or wired brushes SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 16 DREAMLINE EXCLUSIVE LIMITED WARRANTY AS OF MAY 6 2013 This warranty extends only to the original owner end user for household use only and is not transferable to a subsequent owner This warranty extends for a designated period of time so long as it remains in use in its original place of inst
17. hat you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project Please insure that prior to the installation the installation surface is leveled and solid and will be able to support the total weight of the unit Also make sure the walls are at right angles While some adjustment in leveling of the tray is possible irregular installation surface level or improper angle of side walls will result in serious problems for your installation Please note that some adjustments and drilling might be necessary during the installation process IMPORTANT NOTE Dimensions provided for reference only You must measure the actual shower tray sizes before installation Allowed tolerance for center of the drain is 1 2 Tools Required Tape Measure Pencil L evel SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 2 SINGLE THRESHOLD SHOWER BASE Center Drain Configuration U MODEL SPECIFICATION D1 in in DLT 1132320 3232 DLT 1136360 36 36 DLT 1136480 36 x48 30760 327x607 Mex i9 3 _ 3660 3 60 i9 30 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 Left Hand Drain Configuration i MODEL SPECIFICATION D1 in WT1 in DT 30 i19 32 15 DLT 1132601 32 60 L 82 T _ 607 d5 wq 12 DLT 1134601
18. nd solid and will be able to support the total weight of the unit Also make sure that the walls are plumb Depending on the type of unit you are installing some adjustments in leveling may be possible However irregular installation surface level or out of square conditions can result in serious problems for your installation Please note that some adjustments and drilling may be necessary Please protect all primary surfaces of the product during installation Never set your glass down directly onto a tile floor Always use a piece of wood or cardboard to protect the bottom edge and corners of the glass 5 Please NOTE This door has 1 width or out of plumb adjustment in wall profile and 6 width adjustment in pivot hardware 6 a If the width of your door is less than 373 4 and you are installing the door without stationary glass you only need to refer to Diagram A with Packing List A b If the width of your door is 374 and over you are installing the door and stationary glass with glass shelves you have to use Diagram A and B with Packing List A and B to complete the installation Tools Required Seo N B N x Tape Phillips Flat Drill bit Drill bit Caulk Measure Pencil Screwdriver Screwdriver 5 16 1 8 Level Gun Drill Hammer Mallet Knife Allure Rev 3 Ver 1 04 2013 2 Detailed Diagrams of Shower Door Components Diagram A Diagram B Packing List A Wall profile
19. not recommended Apply enough bedding material to support the entire bottom of the shower base See Fig 6 for details Mortar Plaster Fig 6 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 14 6 After the bedding material has been poured and before it sets place the shower base into the position with the drain assembly sliding over the PVC waste pipe It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base Ensure that the base is level in all directions You may need to use shims to hold the tray in the level until the bedding settles and supports the tray Remove all extra mortar See Fig 7 for details Fig 7 Waterproof Drywall Waterproof Drywall 7 Allow the bedding material to completely harden before applying weight to the bottom of the shower base Install the cement board or the wallboard above the tile flanges and secure it to the studs Put the tiles or other finishing material over the cement board leaving 1 8 gap between the bottom of the tile and the Caulk Ceramic Tile splash rim of the shower base Use caulk to fill that gap See Fig 8 and Fig 9 for details SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 15 Product maintenance To insure long lasting life for your acrylic back walls wipe them off aft
20. of one 1 year from initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER amp TUB DOORS SHOWER ENCLOSURES DreamLine warrants shower doors tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for a period of five 5 years from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty for plastic strips shall be limited to one 1 year Warranty for any part in Oil Rubbed Bronze finish shall be limited to one 1 year SHOWER BASES DreamLine warrants shower bases to be free from defects in workmanship and materials under normal residential use for as long as the original consumer purchaser owns their home in which their product is installed SHOWER COLUMNS DreamLine warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER SEATS DreamLine warrants shower seats to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty shall be VOID if the shower seat is not professionally installed on a properly reinforced wall VANITIES AND VESSEL SINKS
21. re Rev 3 Ver 1 04 2013 13 18 After final adjustments of the Assembled unit drill six holes three on each side through the first layer of the Wall profiles and the Glass profiles using O 1 8 drill bit Secure the Wall profile 06 and the Glass profile 05 with Flat head screws ST4 2x10 16 Cover the screw locations with Decorative cover 20 See fig 18 for details 19 Mount the Handle 07 to the Glass door 05 Press the Bottom anti water strip 21 on the bottom edge of the Glass door You can cut the strip to size by using a knife See Fig 19 for details Allure Rev 3 Ver 1 04 2013 Glass shelves installation 20 Mark the Glass shelf 34 position on the wall According to the measurements in Fig 19 1 mark the drilling holes on the wall for the Shelf brackets 26 Drill the holes using 5 16 drill bit and insert the Wall anchors 28 Attach the Shelf brackets 26 to the wall using the Flat head screw ST4 2x25 29 and attach the Shelf brackets 27 to the Stationary glass 25 Insert the Glass shelves into the Shelf brackets and fasten the screws at the bottom of the brackets See Fig 20 and Fig 21 for details Allure Rev 3 Ver 1 04 2013 Fig 21 21 Apply silicone sealant between the tray or threshold the stationary glass and the accessory Also apply silicone between the wall and the wall profiles See Fig 22 for details Silicone Fig 22 NOTE If you need anoth
22. the Wall anchor 15 See Fig 1 for details 2 Push the Pivot retainer 08 into both ends of the Wall profile for small stationary glass 01 See Fig 2 for details Allure Rev 3 Ver 1 04 2013 3 Runa silicone bead along the holes on the wall Attach the Wall profile for small stationary glass O1 and Pivot retainer 08 to the wall using Round head screws ST4 2x40 18 See Fig 3 for details Fig 3 4 Apply clear silicone along the inner channel of the Glass profile for small stationary glass 02 and push the Small stationary glass 03 inside the channel NOTE The small hole on the short side of the Small stationary glass should be located at the bottom and away from the wall NOTE If you have difficulty sliding the Glass profile over the Stationary glass you can slightly tap on the Glass profile with a rubber mallet and a piece of wood Please do not strike directly on the profile or on the edge of the glass panel See Fig 4 for details Allure Rev 3 Ver 1 04 2013 5 Attach the Pivot brackets O9 to the top and the bottom end of the assembled Small stationary glass 03 and the Glass profile for small stationary glass 02 with the Flat head screws ST4 2x25 17 See Fig 5 for details Fig 5 6 Assemble the Glass fixer 10 to the top and the bottom hole of the Small stationary glass 03 Fasten the top Glass fixer 10 to the top Pivot bracket 09 using Fixing nut with M4
23. x12 screw 13 and cover screw location with decorative cover See Fig 6 for details Fig 6 Allure Rev 3 Ver 1 04 2013 7 Slide the Small stationary glass assembly into the groove of the Wall profile for small stationary glass 01 See Fig 7 for details 8 Secure the upper Pivot bracket 09 to the upper Pivot retainer 08 with Socket head screw 14 Adjust the Small stationary glass 03 vertically using a level and fix it in the place by tightening the Socket head screw M6x6 Drill hole into the Shower base through the predrilled hole in the Glass fixer 10 and the Pivot bracket 09 using 1 8 drill and fasten it using Round head screws ST4 2x25 19 Cover screw location with Decorative cover 20 See Fig 8 for details Allure Rev 3 Ver 1 04 2013 9 Attach the top and the bottom Pivot assemblies 12 to the Pivot brackets 09 Make sure the Washer 11 is in between Pivot assemblies and Pivot brackets and the rubber gaskets between the glass and the metal parts Slide the Glass door 04 into groove of the Pivot assemblies and tighten the provided fasten bolts Push the Magnetic strip on door 23 on the vertical edge of the Glass door See Fig 9 for details NOTE Smaller cut out on the Glass door panel must be on the bottom and deeper cut out must be on the top ATTENTION a If the width of your door is less than 3734 and you are installing the door without station
Download Pdf Manuals
Related Search