Mr. Steam 104040PB Installation Guide
Contents
1. Open End Container Cap Suction Hose Filt r 24s l Container Height 8 inches Figure 3 mr steanr AromaSteam Operation and Installation Instructions Installation of Suction Hose to AromaSteam System Suction Suction Pump Pressure Pressure End Nut Valve Head Valve End Nut 1 Unscrew the suction end nut from the pump head and remove S e i short end of shipping hose discard shipping hose keep pressure end nut 2 Remove suction end nut from the shipping hose 3 Insert the open end of the suction hose through the hole of the suction end nut 4 Firmly push the hose onto the cone of the suction valve at the pump head 5 Screw the suction end nut to the suction valve IMPORTANT NOTE HAND TIGHTEN ONLY Figure 4 Typical AromaSteam Installation FOR USE WITH iSTEAM AND iTEMPO PLUS CONTROLS ONLY Locate the AromaSteam system to monitor the consumption of essential oils and for easy oil replacement a Q isteam J Typical Mr Steam Steam Generator NOTE CABLES SHOULD NOT CONTACT STEAM PIPE Cable to Steam Generator _ request cable Steam Head N AromaSteam STEAM ROOM System Noung rackets For illustrative Purposes Only tT Pump Line Cord 240V _ grounded receptacle required aa mr steanr AromaSteam Operation and Installation Instructions Electrical Connection of AromaSteam Wiring AromaSteam AromaSteam Syste2. K fu AN Installation Operation amp Maintenance Manual AromaSteam mr steam Feel Good Inc mr ste am AromaSteam Operation and Installation Instructions MS AromaFlo Table of Contents BOX CONLGHIS lt cucut ke eeceweeweaaeaes 3 General Installation 0 3 Installation of Hoses 0085 4 Assembly Diagram 0 005 5 Electrical Wiring 0 0 e ee ee eee 6 Start up MitalPimNg v eevetase ones aoe ees 6 Filling the Pressure Hose 6 Operation 622 cscsneaedent seeede ews 7 Adjusting amount of oil delivery 7 Troubleshooting 0 e eee 8 Technical Information 000 8 AromaSteam for illustrative purposes only e Do not use with water soluble fra grance or fragrance containing emulsi fiers or aldehydes AromaSteam sys IMPORTANT NOTE The warning label supplied shall be posted in a conspicious tem damage may result Mr Steam oils location next to the steam room door are approved for operation with this eae A WARNING e The use of any oils other than Mr Steam oils may introduce excessive concentration of oil into the steam This room is equipped with an aromatic oil dispensing system room resulting in a health hazard l l l i A T Leave the room immediately if you have any adverse or allergic ae n of bs hess reactions including difficulty breathing or eye nasal throat nse immediately with plenty of wa
3. Installing the 90 degree T and Atomizing Nozzle 90 T 1 For optimal results locate a brass 90 degree T not provided and atomizing nozzle Steam Line in the steam supply line within 10 feet of the steam head If using copper tubing for T e ee steam lines install a female 1 2 NPT thread to sweat fitting in the downward facing T 1 2 NPT 2 T must face downward as shown in figure 2 3 Screw the atomizing nozzle into 90 T fitting using teflon tape on the threads IMPORTANT NOTE Follow the installation instructions for the steam pipeline in the Mr Steam Steam Bath Installation and Operation Manual Visit www mrsteam com to download this document Installation of Pressure Hose to AromaSteam System 1 Unscrew the pressure end nut from the pump head and remove the shipping hose and the pressure end nut 2 Insert the pressure hose through the hole of the pressure end nut and firmly push the pressure hose onto the pressure valve 3 Screw the pressure end nut onto the pressure valve and tighten the nut by HAND only Installation of Suction Hose in Scent Container 1 Locate the container cap 2 Unscrew the cap from the Mr Steam scent container and discard 3 Insert the suction hose with the open end from below through the hole in the container cap see Fig 3 4 Insert the filter into the scent container so that the filter rests on the bottom 5 Screw the cap onto the scent container Figure 2
4. 00 72 STEAM Fax 310 216 2944 Motor Operated Pumps 24VW mr steanr AromaSteam Operation and Installation Instructions BOX CONTENTS Shipping Hose 2 Se a Ss D HHH if 6 ft A Pressure 1 2 inch NPT il e o W Hose y Atomizing Nozzle Nx A Lp AromaSteam Ei ae Of a ae N A Us N Injector with ii 2 ft Suction Injection Hose mE Steal Fee Good inc AromaSteam System amp f Bracket Assembly ose T i with integrated 6 ft power cord with Filter Installation amp Operation Manual 8 ft request cable Y Lp with Peel off Warning Label ee say amp Y GENERAL INSTALLATION The AromaSteam system is qualified for use with Mr Steam residential and CT steam generators ONLY IMPORTANT NOTE AromaSteam is for use with iSteam and iTempoPlus controls only 1 Locate the AromaSteam system to monitor the consumption of essential oils and for easy oil replacement 7 2 The warning sticker provided must be placed in a conspicuous location WARNING near the steam room door This room is equipped with an aromatic oil dispensing system Leave the room immediately if you have any adverse or aller 3 Mr Steam AromaSteam System is designed and intended for indoor on ra a a a eaa use only and is to be located indoors in a dry clean location and not throat or skin irritation and seek medical attention subject to moisture condensation or similar high humidity environments mr steam 43 20 34th Stree
5. at preset intervals Adjusting the Amount of Oil Deliver The AromaSteam system has been factory set to deliver a suitable amount of aromatic oil into a typical sized steam room Please contact the MrSteam Technical Service Department before changing this setting Increasing the settings may introduce excessive concentra tion of oil into the steam room resulting in a health hazard Contact the Mr Steam Technical Service Dept at 800 76 STEAM East coast or 800 72 STEAM West Coast for assistance or additional information Only a qualitied licensed electrician or factory authorized personnel may adjust the factory setting mr steam TROUBLESHOOTING TO AVOID ELECTRIC SHOCK DISCON NECT POWER TO PUMP BEFORE SERVICING Metering pump does not prime 1 Check if voltage is available 2 Check liquid level in scent container Replenish liquid if necessary 3 Check for air bubbles in the suction hose or the pump head To eliminate air bubbles see Priming Pump 4 Check valves for contamination Clean valves if necessary 5 Check filter in container for contamination Rinse filter under clean water Metering pump does not inject oil into steam room 1 Check if voltage is available 2 Check liquid level in scent container Replenish liquid if necessary 3 Check for air bubbles in the suction hose or the pump head To eliminate air bubbles see Priming Pump 4 Check valves for contamination Clean va
6. ct go to blog mrsteam com wr m 2014 Sussman Automatic Corp MR STEAM and des AROMAFLO AUTOFLUSH CLEAN STEAM EVERY TIME CLUB THERAPY DIGITAL 1 FROM BATHROOM TO SPA BUTLER PACKAGE CHROMA STEAM EXPRESS STEAM MAKING WELLNESS a WAY of LIFE MUSIC THERAPY STEAM ON DEMAND STEAM HOME iGENIE STEAMTHERAPY SUSSMAN and VALET PACKAGE are registered trademarks of Sussman Automatic Corp AUDIOWIZARD HOME WIZARD iTEMPO iTEMPO PLUS STEAMSTART STEAM STOP and THE INTELLIGENT STEAMBATH are trademarks of Sussman Automatic Corporation
7. lves if necessary 5 Check filter in container for contamination Rinse filter under clean water 6 Check the pressure hose for kinking or jamming Straighten or replace 7 Check if liquid is freely flowing through the atomizing nozzle when the metering pump is energized Apply compressed air through the atomizing nozzle Attach the compressed air at the point of connection of the pressure hose 8 For iTempoPlus ensure the demand button light is ON The demand button light should be pressed during installation the light will turn on In the event of a power outage the button will need to be pressed again Metering pump oil delivery too much or too little Contact Mr Steam technical service personnel at 1 800 76 STEAM East Coast or 1 800 72 STEAM West Coast AromaSteam Operation and Installation Instructions TECHNICAL SPECIFICATIONS LIST OF SPARE PARTS Description Part No Pump Head 103861 Pressure Suction Hose EO1 1032 ordered by the foot Eucalyptus oil 1 liter MS OIL 1 Lavender oil 1 liter MS OIL 2 Evergreen oil 1 liter MS OIL 3 Energizing Mint oil 1 liter MS OIL 4 Poho oil 1 liter MS OIL 5 Atomizing Nozzle 103918 Oil Injector 103983 Filter 103987 Valve Rebuild Kit 104159 Dimensions 11 5 W x 9 5 H x 4 5 D Weight 5 pounds Motor voltage 120VAC 50 60 Hz Power consumption total W 12 Watt WARRANTY To view or download m m the Mr Steam Control Warranty and register your produ
8. m Schematic I Plug This AromaSteam system is factory wired If l 120 VAC the power cord of the Aroma Steam system is damaged it must be replaced by the Sussman Automatic service ee e l grounded receptacle department or similarly qualified personnel in order to required avoid an electric shock hazard All electrical connections to auer CBE be made by a licensed qualified electrician Disconnect all 24 VAC to steam generator power to the steam generator before sen below making power connections IMPORTANT NOTE AromaSteam is for use with iSteam i k AromaSteam Connections ZON and iTempoPlus controls only AROMA 1 Disconnect all power to the Mr Steam steambath generator and remove the top cover 2 Run the request cable from the AromaSteam System through one of the knock outs in the side of the steambath generator Use a strain relief bushing or grommet to prevent chafing 3 Locate the two quick connect tabs labeled AROMA on the PC board in the location show 4 Connect the request cable to the terminals The terminals are not polarized START UP Initial Priming of the Pump Figure 5 Pressure Valve 1 Insure Mr Steam scent container is full 2 Insert the short injector hose onto the tip of the injector see Fig 5 3 Unscrew the pressure end nut from the pump head and remove the Injector pressure hose from the pressure valve Hose 4 Insert the open end of the injection hose onto the press
9. t Long Island City NY 11101 800 76 STEAM www mrsteam com PUR 100405 4 Do not install AromaSteam Systems outdoors 5 Do not install AromaSteam Systems in a location where water could freeze 6 Do not install AromaSteam Systems near flammable or corrosive materials and chemicals Installation in areas having high concentrations of chlorine such as pool equipment room should be avoided 7 Attach the AromaSteam System onto a secure vertical surface 8 Provide access to AromaSteam System for servicing and refills 9 The system should not be installed in areas accessible to children A LOCKED ROOM IS STRONGLY RECOMMENDED ie utility room 10 Height difference between AromaSteam System discharge and 90 degree T is to be held to a maximum 6 ft see page 5 11 Do not exceed 30 feet of tubing between the pump head and atomizing nozzle mr steam GENERAL INSTALLATION cont Clearance to heat sources AromaSteam Operation and Installation Instructions e Do not install the AromaSteam system directly below or above the Mr Steam steam generator where it is subject to heat e Minimum distance between the AromaSteam system and a heat source e g steam generator heating system is 1 5 ft If this minimum distance of 1 5 ft cannot be maintained install a radiation plate or heat insulation between the heat source and AromaSteam system e Ambient temperature at and around the AromaSteam system should not exceed 90 F
10. ter OF Skin irritation and seek medical attention and seek medical advice If swallowed rinse mouth with water only if the person is conscious seek medical advice immediately and show this container or label mr steam 43 20 34th Street Long Island City NY 11101 800 76 STEAM www mrsteam com PUR 100405 Highly Flammable Keep away from sources of ignition No smoking Keep container tightly closed amp in a well ventilated place This material amp its container must be disposed of as ae P ANEAN states a hazard may cause serious injury or death if precautions are not followed hazardous waste Not f lic or fiberg sh aie a ARANAN signals a situation where minor injury or product damage may occur if you do not IMPORTANT NOTE As you follow these instructions you will notice warning and caution symbols This blocked information is important for the safe and efficient installation and operation of this generator These are types of potential hazards that may occur during installation and operation rooms follow instructions e Material Safety Data Sheet MSDS available upon request IMPORTANT NOTE This highlights information that is especially relevant to a problem free installation Mmfr St aM sussman Automatic Corporation hello mrsteam com www mrsteam com PUR 100402 Rev 2 14 43 20 34th Street Long Island City NY 11101 9410 S La Cienega Blvd Inglewood CA 90301 1 800 76 STEAM Fax 718 472 3256 18
11. ure valve see Fig 5 5 Draw liquid from the injector slowly and evenly Continue until the injector is full of liquid 6 If you have drawn up the injector completely and no liquid is in the injector remove the injector hose from the pressure valve 7 Drain injector Repeat steps until the injector is filled 8 Save the oil injector as it will be needed when new oils are used Filling the Pressure Hose Figure 6 1 Insure the AromaSteam System is primed and the scent container AromaSteam is full Metering Pump 2 Locate the Push button at the rear of the metering pump see Fig 6 Depress this push button to start metering pump 3 Continue to depress push button until the pressure hose is filled with liquid IMPORTANT NOTE Push button to be used only for initial filling of the pressure hose and after new oil bottles are installed mr steanr AromaSteam Operation and Installation Instructions OPERATION mr steam iSteam 1 Press the START button to turn the steam generator on 2 In the dashboard press the AROMA button the button will be highlighted when AromaSteam is on Aromasteam 3 Aroma oils will automatically be pumped into the steam line at preset intervals iTempoPlus 1 Press the ON OFF button to turn the steam generator on 2 Press the AROMA button AROMA will be displayed on the screen when AromaSteam is on 3 Aroma oils will automatically be pumped into the steam line
Download Pdf Manuals
Related Search