American Standard 7005.901.002 Installation Guide
Contents
1. supply to inlet of right VALVE using appropriate connector HOT FOR FITTING LESS SPRAY 8 E 11 MOUNTING SURFACE 2 INSTALL HANDLES Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is facing up Fig A Tighten STEM SCREW 3 to secure ADAPTER 1 Align HANDLE BASE 4 and push onto HANDLE ADAPTER 5 until flush against mounting surface Find correct position of LEVER HANDLE 6 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 6 Tighten SET SCREW 7 with 5 64 HEX WRENCH 8 SUPPLIED SERVICE To change direction of handle Turn valve to OFF position Remove SET SCREW 7 with 5 64 Hex Wrench Pull HANDLE 1 UP firmly to release from ADAPTER 3 Pull HANDLE BASE 6 off DECK ADAPTER 2 Remove SPRING CLIP 4 Lift STOP WASHER 5 turn 90 and replace Replace SPRING CLIP 4 Re install HANDLE ASSEMBLY If Tu drips operate handles several times from OFF to ON position Do not force handles turn only 90 5 64 HEX WRENCH M968638 REV 1 1 HANDSHOWER INSTALLATION FOR MODEL 7005 901 ONLY Drop SPRAY ESCUTCHEON 1 through the fourth hole of the tub ledge 12 max from SPOUT center with SPRAY ESCUTCHEON 1 directed towards tub center Be sure RUBBER RING 2 is properly seated in ESCUTCHEON 1 Install RUBBER WASHER 3 and LOCKNUT 4 from underside of ledge Secure S2. American Standard Installation Instructions COPELAND 7005 900 DECK MOUNT BATH FILLER 7005 901 Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ANSI A112 18 1M M968638 REV 1 1 Recommended Tools ROUGHING IN DIMENSIONS C 3 ADJ 6 1 2 TO 12 gt j Flat Blade Screwdriver T 1 1 2 3 4 8 3 16 Wrench MOUNTING SURFACE y Adjustable Wrench 1 1 8 DIA gt Toor 7 z Ee U 3 16 DIA Channel Locks 3 414 MALE m Hex key N PT INLETS 1 1 16 DIA Supplied with Fitting j SPOUT ASSEMBLY oy Veale ae Tern off hot and cold water E Prepare TUBE and TEE ASSEMBLY 1 to fit center to center EEI cries petore beginning VALVE 2 location between 6 1 2 and 12 If necessary E Install RING WASHER 1 into SPOUT recess Check that O RING 2 cut and or bend TUBING carefully Make sure tube bend is on end of SPO
3. PRAY ESCUTCHEON 1 by tightening LOCKNUT 4 Add SEAL WASHER 5 and connect HOSE 10 to outlet nipple at the bottom of TEE 7 Tighten firmly Slip SHOWER HOSE 8 with COUPLING NUT through SPRAY HOLDER 6 and ESCUTCHEON 1 Note SPRAY HOLDER 6 must be separate from ESCUTCHEON 1 to get HOSE 8 thrrough ESCUTCHEON 1 Install SEAL 9 and connect both HOSES 8 and 10 INSTALL second SEAL 9 and connect HAND SHOWER 11 to SPRAY HOSE 8 NOTE When not in use HANDSHOWER should be seated in the HOLDER CAUTION 7 TEST INSTALLED FAUCET eect The flow rate of this Tub Filler exceeds 20 gallons minute at higher water pressure Do not fill bathtub unattended Turn VALVES 1 to off position With handles in off position turn on water supplies and check all connections for leaks Operate both handles and flush water lines thoroughly Check SPOUT 2 mounting for leaks Lift HANDSHOWER 3 from holder direct spray into tub lift TRANSFER KNOB 4 to check HANDSHOWER 3 and HOSES for leaks Turn VALVES off If spout drips operate handles several times from OFF to ON position Do not force handles turn only 90 Before the bathroom is completely finished you may want to remove spout handshower and handles E To remove handles reverse steps in STEP 4 f Hex wench supplied E To remove SPOUT 1 proceed as follows Lift KNOB 2 and unscrew from TRANSFER ROD 7 Remove SET SCREW 3 u
4. UT SHANK 3 is in place Insert SPOUT SHANK 3 close to the TEE 1 so that it will not effect the compression through center hole on mounting surface joint at the VALVE CONNECTION Remove COUPLING NUT 3 and FERRULE 4 from each Assemble RUBBER WASHER 4 and BRASS WASHER 5 and VALVE 2 and slide onto TUBING 5 LOCKNUT 6 onto SPOUT SHANK 3 Align SPOUT ASSEMBLY and from underside of ledge secure SPOUT ASSEMBLY into position with LOCKNUT 6 ASSEMBLY MOUNTING MOUNTING SURFACE SURFACE VALVE inlet is 3 4 inch NPT male 69 VALVE ASSEMBLY 41 MOUNTING SURFACE Install LOCKNUTS 1 and RUBBER WASHERS 2 onto valve shanks Push TUBING 3 ends into VALVE 4 side outlets Insert VALVES 4 into mounting holes from underside of ledge Press TEE 5 onto SPOUT SHANK 6 making certain that the O RING 7 is properly seated on SHANK 6 Push COUPLING 8 or 8a into TEE 5 and attach to SPOUT SHANK 6 and tighten For 7005 901 use a 10 mm 3 8 hex key Thread of VALVE BODY 4 should extend at least 5 16 inch above MOUNTING SURFACE 11 If necessary adjust LOCKNUT 1 Place RUBBER RING 10 into ESCUTCHEON ADAPTERS 9 and thread onto valves until snug against internal stop Tighten LOCKNUT 1 to secure VALVE 4 position Slide FERRULE 1712 and COUPLING NUT 13 to outlet of VALVE 4 and tighten COUPLING NUT 13 firmly Connect HOT water supply to inlet of left VALVE and COLD water
5. sing 5 mm hex wrench supplied Lift SPOUT 1 off SHANK 4 carefully and remove RUBBER RING 5 Unscrew SHANK SLEEVE 6 and lift TRANSFER ROD 7 from SHANK 4 Reverse sequence to re install SPOUT 1 Be sure RUBBER RING 5 is properi seated in its recess at the base of SPOUT 1 Make certain SET SCREW 3 is properly aligned and tight so that SPOUT 1 is locked in place CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH ea eared For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID se POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A ay Weekdays 8 00 a m to 7 00 p m EST COARSE SURFACE IN MEXICO 01 800 839 12 00 Product names listed herein are trademarks of American Standard Inc American Standard Inc 2007 M968638 REV 1 1
Download Pdf Manuals
Related Search