eLEDing EE860DDC(B) Use and Care Manual
Contents
1. If this unit has been stored over six months before initial operation then the battery may need to be re charged To re charge the battery after storage turn the main switch to OFF connect the battery plug the wire cord from the solar panel into the light and place it in direct sunlight for 1 2 days Or charge for 2 3 hours using only our optional accessory AC DC Digital Switched Power Adapter EE DPS 0 8A The Li Battery will charge in any of the three switch position including OFF 7 Spot Light Projection Lighting as Traditional full bright ON without motion This option converts the light to provide continuous adjustable up to full brightness level illumination for up to 8HRS or more It can be used as a wall washing light to project lighting on signs flags and areas that need spot lighting Set the main switch to position A Then make sure to adjust the Left Dial from M or all the way to the max H position as desired and adjust the Right Dial Sensitivity to the lower L position refer Fig 2 8 An optional AC DC digital power adapter EE DPS 0 8A Fig 5 can be used as a quick charger Also with this adapter it can be used in all profiles and modes as a standard AC DC powered motion sensing flood light with battery back up capability for indoor outdoor security safety lighting applications It can be wall or table mounted or used as a standard portable table light Fig 5 Using this option it can be used in any of the three profiles 9 I2. for the desired level of soft glow illumination when motion is not detected L M is recommended Set the Right Dial between L to H M to below H is recommended 3 SMART AUTO Profile Mode Motion activated lighting only Set the Main Switch to either A or B Set the Left Dial to AUTO in the far left position Set the Right Dial between L to H M to below H is recommended F Main Switch Lighting Adjustments OFF SMART A amp B profiles with A p Dimming level adjustments B from Min L to Max H Left Dial EX Sensitivity Range s Position for 5 45 SMART Right Dial AUX power Input AUTO Mode Fig 2 Functions Rev EE860plus 072015 Page 1 SMART AUTO Profile In either A or B position if the Left Dial is set to Auto turned all the way to the far left past L to the Auto position then this light will convert to operate as a traditional motion sensing light In this SMART AUTO mode it will light up to full brightness when motion is detected When the Left Dial is set at the AUTO position the illumination time has a fixed 60 second delay time for the light to be ON after motion is detected and the lighting will be extended as long as motion is continually detected It will not turn off until the motion detection has stopped and after the illuminating Delay Time has expired The motion Sensitivity Range can be adjusted using the Right Dial Ref Fig 2 page 1 to set the desired Sensitivity Range for
3. the application This adjustment has a motion sensing range from Low 5 Med 15 High 40 For most applications set the dial to between M H in warmer temperature environmental locations set this slightly higher User Tips video reference www eesgi com 1 To set up your new eLEDing light for your applications the unit comes with an initial Set up Walk Test mode to ensure proper installation and performance is optimized To activate this mode move the main switch from OFF to B position as SMART B profile This test mode can be reactivated at anytime night or day to adjust your settings for your application by sliding the switch to OFF then to B position and then making your dial settings 2 When the main switch is set initially to SMART B profile from the OFF position the Set up Test mode will be active for a period of 10 minutes allowing the user to adjust the light settings This mode will work in day or night time conditions The Motion Sensitivity Range right dial can be adjusted at this time for your application from 5 minimum to 45 maximum 3 The Set up Walk Test mode is active as long as motion is detected and it will automatically disable itself if 10 minutes has passed without motion being detected During this test period the small Red LED indicator will flash providing visual motion sensing reference as a confirmation of motion detection adjustments When a period of 10 minutes passes without motion detection the unit will aut
4. If this does not make an indication that means the battery s status is fully charged 6 Open the left side cover refer Fig 2 move the function switch to B position recommended to start the Initial Set up or Walk test procedure Please refer to the 3 Mode Selectable One step Set up instructions and also refer to Page 2 for procedure details Must remove the protective film on top of the solar panel before using 7 After the Initial Set up test if there is no motion during the testing delay time period 10 min the unit will enter into normal operation and illuminate automatically only when the environment becomes dark Connect Mounting Mark Points for Setting Reference as Option on light bod _ Li Battery p g y before 1 operation Fig 1 1 Mount on the Two Screws Fig 1 Installation Steps 3 Mode Selectable Set up Refer Fig 2 and PG 2 for more info disregarding light plastic mark 1 SMART B Profile Mode Max bright adjustable This mode is recommended and can be used for most illumination lighting applications Set the Main Switch to B downward position Set the Left Dial between L H for the desired Max brightness level above soft glow illumination once activated by motion M H is recommended Set the Right Dial between L to H M to below H is recommended 2 SMART A Profile Mode Soft Glow Dimming brightness adjustable Set the Main Switch to A in the center position Set the Left Dial between L H
5. eLEDing Model EE860plus User Manual SMART plus Solar Light built with 60 super bright LEDs IMPORTANT Read this User Manual Before Installing Introduction and Intellectual property Rights Statement Thank you for using the EE860plus light is upgraded dual operating SMART modes with outstanding performance and enhanced Li Battery capacity With its effortless setup and lightweight design the EE860plus LED Smart Light conforms to all your lighting needs It was designed and built to provide many years of trouble free service using environmentally friendly Solar Hybrid Lithium based energy technology This product is covered under multiple US European China and other International patents granted and pending worldwide All rights reserved Initial Installation Refer to Fig 1 Connecting the Battery before setting up 1 The battery has been pre charged before shipping and the light is ready for use 2 Make sure the main switch is in the OFF position 3 Open the battery compartment cover on the back of the light and plug the battery into the connector and carefully make sure the plug position is correct then replace the cover Fig 1 1 4 Initially check the LED illuminator and battery by slowly moving the main switch to position A or B it should light up then turn the switch back to OFF for installation Mounting the Light Fixture 1 Choose a flat and stable mounting surface with maximum exposure to sunlight Cut the mo
6. mportant Note Lowering the Left Dial setting in either A or B profile will extend the battery capacity reserve and provide extended illuminating ability in geographic locations with poor sunlight such as North West and North East of American e g Specifications Light fixture Black Color BP or White Color WP PC plastic Detecting Range adj 160 up to 45 x 45 L 5 1 5m to H 30 9m Light Head Super 60 SMT LED up to 160 W x 140 V 4000K Color Green Energy Storage 16WH Li Poly Lithium based battery Solar Panel 12VDC 3 0W Monocrystalline Smart Modes Mode B upto 40 hrs Mode A 9 40 hrs w IPM Brightness Up to 700 Lumens 60W standard lamp on peak Operation Temp 4 F to 125 F Consumer Standard Weatherproof IP54 Weight 1 6LBs Demension L 13 3 8 x W 4 1 2 x H 3 3 8 Complies with FCC Part 15 Class B and ICES 003 2004 CE Continuous dimming illumination Dusk to Dawn capability claims under fully charged battery and no motion triggered condition One Year Limited Warranty Bend off this piece for additional Charge During Day EESGI guarantees this product to be free from defects in material amp pola Paver Oh ann poweh 2oulce workmanship for 1 year This warranty does not apply to damage from misuse or incorrect installation connection This warranty does not cover accessories bulbs batteries accidents alterations unauthorized use or repair neglect misuse abuse y damages or defects res
7. omatically switch to normal operation mode It will stop illumination if the set up test was made during daylight conditions and it will start illumination again once it Senses a change to darkness from daylight ambient light conditions 4 After the initial Set up Walk Test is complete the main switch may either be kept in the SMART B profile or set to the SMART A profile For most applications SMART B position is recommended In both A and B profile if the Intelligent Power Management IPM system detects that the battery does not have enough capacity to operate these modes in critical weather conditions then it will convert to AUTO mode And if it detects that there is insufficient battery reserve to operate in Auto mode then it will automatically disable illuminating functions leaving only the charger active to protect the battery from being damaged After enough sunlight is received to charge the battery the unit will first return to AUTO mode for motion activated lighting until it receives enough sunlight energy to operate the SMART profiles properly 5 Note The Red LED indicator light flashes for the following reasons 1 To indicate motion activity during the 10 minutes initial Set up Walk Test 2 To indicate the battery is low when the sensor detects motion during darkness 3 To indicate charging status during normal charging daylight conditions or when the AC DC digital charger optional is being used for charging in any conditions 6 Storage
8. ulting from normal wear and tear including chips fading scratches abrasions or discoloration due to usage or sun exposure or failure to follow instructions for care and maintenance fire flood and Acts of God fx a e a Illuminating Coverage up to This warranty does not include liability for incidental or consequential ee 180 Horizontal Profile Install the aux panel in direct papain i damages Pal sun remotely from the light 140 Vertical Profile EESGI is not responsible for any damages in excess of the retail i with the Unique Optic Reflective Arrangement purchase price of the product under any circumstances The consumer Aa is responsible for the installation of removal of and reinstallation of the Fig 3 Optional Solar Panel for insufficient sun exposure locations product d or indoor use of the light Customer service 877 579 3889 www eesgi com 7 Rev EE860plus 072015 Page 2
9. unting template from the back of the package and use it to mark the two screw mounting holes The screw mounting holes also have reference Marks on the light body refer Fig 1 2 2 For wood mounting surfaces Drill the screws into the pre marked locations and mount the unit on wall For concrete brick stucco Pre drill clearance holes using a 3 16 masonry bit Insert the plastic anchors and screws Then mount the unit on wall This light can be mounted horizontally in a high position to project light toward the ground or it can be mounted vertically to project light sideways onto walls or gated areas 3 This light fixture with integrated solar panel must be mounted in a non obstructed position where it will receive an average of at least 4 hours daily of direct sunlight all year round It requires a sturdy mounting location such as a building house fence wall patio roof under the eaves or secure pole e g Securely mounting this unit and self contained solar panel ensures that it will perform well in all weather conditions 4 For Northern hemisphere installations this light fixture should be mounted with a Southerly facing position and visa versa for Southern hemisphere installation it should face to the North Australia South Africa South America e g 5 A small RED LED indicator under motion detector lens will begin making a double flash indicating that charging status is active during a normal sunny partially sunny or cloudy day
Download Pdf Manuals
Related Search