Illumine CLI-EMM030840 Installation Guide
Contents
1. Any electrical work not described in these instructions should be done or approved by a licensed electrician y retainers securing the motor hub in the motor housing NOTE Take care not to scratch the fan housing when installing the blade assemblies C13 Rotate the motor hub to position the slot in the motor plate over a fan motor housing flange hole Attach the blade flange assembly on the fan motor housing by slowly rotating the motor hub to align screw holes Tighten the screws securely while interlocking the flange assemblies as you rotate the hub Figure 5 Your ceiling fan can be assembled with the light kit and glass or without the light kit and glass To assemble without the light kit and glass you will use the no light cover plate In order to use the no light cover plate the light sockets will need to be removed from the light kit plate NOTE In order to remove the light sockets the wires on the light kit plate will need to be cut MAKE SURE THIS IS THE NO LIGHT ASSEMBLY DESIRED 02 Remove and discard the three shipping 1 4 Connect the white wire from the fight kit plate to the whiie wire in the fan motor housing assembly Figure 6 Connect the black wire from the light kit plate to the black wire in the fan motor housing assembly LIGHT KIT PLATE BLACK WIRE BLUE WIRE FAN MOTOR HOUSING ASSEMBLY Figure 6 CAUTION Before installing and tight ening the screws be s2. DECORATIVE OD ASSEMBLY Aa WARNING It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened Failure to verify that the pin and setscrew are properly installed could result in the fan falling
3. suitable for use with solid state speed controls WARNING To reduce the risk of fire or electric shock this fan should only be used with fan speed control Model No UC7067RA manufactured by Rhine Electric Co Ltd WARNING This product is designed to use only those parts supplied with this product and or any accessorles designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades DATE CODE The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep it in a safe place for future use BP7375 1 Highpointe 8 19 10 2 50 PM ep 3 This Manual is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Your Ceiling Fan Tools Needed for Assembly 1 Open styrofoam unit containing fan One Phillips head screwdriver One wire siripper One stepladder One wire cutter Materials Wiring outlet box and box connectors must be of type required by the local code The minimum wire would be a 3 conductor 2 wire with ground of the following sizes Installed Wir
4. bs id READ AND SAVE THESE INSTRUCTIONS Ceiling Fan Owner s Manual Net Weight 22 1 Lbs Part No F40BP73750001 b A WARNING WARNING To avoid fire shock and serious personal Injury follow these instruc tlons Safety instructions Read your owner s manual carefully and keep it for future reference Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from belng switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the ceiling fan before servicing Do not put anything into the fan blades while they are turning Do not operate reversing switch until fan blades have come to a complete stop Additional Safety Instructions for Installation To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades The installation Is to be in accordance with the National Electrical Code ANSI NFPA 70 2008 and Local Codes Use the National Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precaution against possible electrical shock Electrical installation should be made or approved by a licensed electrician The outlet box and joist
5. e Length Wire Size A W G Up to 50 ft 14 50 100 ft 12 mem same eo TS Unpacking Instructions For your convenience check off boxes are provided next to each step As each step is completed place a check mark in the box This will insure that all steps have been completed and will be help ful in finding your place should you be interrupted 4 WARNING Do not install or use fan if any part Is damaged or missing 44 WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal Injury or property damage Remove top half of styrofoam unit Remove parts and check to see that you have received the following parts NOTE If you are uncertain of part description refer to exploded view illustration Homo posg ie NOTAN Fan motor nousing assembly One ceiling cover One coupling cover Three fan blades Three blade flanges Nine decorative blade nuts bagged One hanger bracket One hanger ball i2 downrod assembly One 6 downrod One rod support assembly Three decorative rod assemblies Six decorative rod assembly screws bagged One light kit plate One lower glass One cover plate Two 50 watt mini candelabra base halogen bulbs One remote cont
6. e hairpin clip snaps around the clevis pin The hairpin clip must be properly installed to prevent the clevis pin from working loose Pull up on the downrod to make sure the clevis pin is properly installed o 7 a installed in the rod support assembly Then position the three screws in the rod support toward the top and slide the rod support over the downrod Figure 10 ROD SUPPORT ASSEMBLY ener SCREWS 3 Toward Top COUPLING MOTOR Se HOUSING Figure 10 O 12 Using the decorative rod screws sup plied attach the three decorative rod assemblies to the motor housing Figure 11 The decorative rods must be oriented so that they lean in towards the downrod Do not tighten the rod screws at this time DECORATIVE ROD ASSEMBLY DECORATIVE ROD SCREW t W A O O Figure 11N 011 Make sure the grommets are propery L 13 Slide the rod support assembly up the downrod until the threaded holes in the rod support align with the holes in the decorative rod assemblies Figure 12 Secure the decorative rods to the rod support using three decorative rod screws do not tighten the rod screws at this time O 14 Rotate the rod support assembly until the decorative rod assemblies are aligned vertically with the downrod Figure 12 Hold the rod support in this position while tightening all six decorative rod screws securely DOWNROD ORT DECORATIVE ROD SCREW
7. l until the ball falls freely down the downrod Figure 8 Remove the pin from the downrod then remove the hanger ball Retain the pin and hanger ball for rein stallation in Step 15 O9 Tighten the setscrews Figure 9 securely while pulling up on the downrod NOTE The setscrews must be properly installed as described above or fan wobble could result supplied in order to maintain the necessary blade to floor clearance of seven feet Figure 8 18 Unscrew the two upper setscrews PIN HANGER BALL DOWNROD Figure 8 until they clear the inside of Figure 9 the motor coupling Then separate untwist and unkink the three 80 motor 410 Make sure the grommet Is properly leads Route the motor lead wires installed in the coupling cover then through the downrod Align the clevis slide the coupling cover over the pin hotes in the downred with the holes downrod until it rests on the motor in the motor coupling Install the clevis housing Figure 10 in and secure with the hairpin cli Fe Figure 9 The clevis pin sie NOTE If you installed the 6 downrod through the Folds ante moter aoi the three decorative rod assemblies k and the rod support assembly will not pling and the holes in the downrod Be be installed Disregard Steps 12 sure to push the straight leg of the hairpin clip through the hole near the through 14 proceed to Step 15 end of the clevis pin until the curved portion of th
8. must be securely mounted and capable of reliably supporting at feast 50 pounds Use only U L outlet boxes listed as Acceptable for Fan Support and use the mounting screws provided with the outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need te be replaced Consult a qualified electrician if in doubt The longer downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for a 9 foot ceiling The 6 downrod supplied must be used for an 8 foot ceillng The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades Follow the recommended Instructions for the proper method of wiring your ceiling fan lf you do not know enough about electrical wiring have your fan installed by a licensed electrician CAUTION The halogen bulbs operate at high internal pressure and high surface temperatures and could shatter unexpectedly The halogen bulbs generate UV ultraviolet radiation that may cause skin and eye Irritation with prolonged exposure To avoid risks of burns or other injury assure power is off before attempting to install or replace halogen bulb Do not operate fan Iight without lower glass in place 7 This fan uses halogen bulbs Do not touch the bulb with bare hands Fingerprints may result in shorter bulb life Remove fingerprints with alcohol NOTE This fan is
9. n against possible electri under the ceiling cover This system cal shock allows you to regulate your ceiling fan speed and light intensity NOTE An optional Emerson Electric How to Assemble Your SW406 Wall Control may also be used Ceiling Fan to control your ceiling fan 1 Mount the fan blades to the blade flanges using three 10 24 x 9mm oval x head screws and three decorative Electrical Requirements blade nuts supplied Figure 4 Your new ceiling fan will require a ground ed electrical supply line of 120 volts AC Aa WARNING 60 Hz 15 amp circuit The outlet box must be securely anchored and capable of withstanding a load of at To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balanc least 50 pounds ing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades A WARNING To reduce the risk of fire electric 10 24 X 9mm OVAL shock or personal injury mount fan HEAD SCREW 3 to outlet box marked Acceptable for Fan Support and use screws sup plied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electri BLADE FLANGE e I cian if in doubt 1 FAN BLADE DECORATIVE WARNING a BLADE NUTS 3 Figure 4 To avoid possible fire or shock fol low all wiring instructions carefully
10. rol transmitter One remote conirol receiver One loose parts bag containing Two 1 1 4 threaded studs Two knurled knobs Two lockwashers Seven wire connectors One hairpin clip One clevis pin Seven 1 4 20 x 11mm pan head screws bagged Ten 10 24 x 9mm oval head screws bagged NOTE Place the parts from the loose parts bags In a small container to keep them from being lost If any parts are missing contact your focal retaller or catalog outlet for replacement before proceeding et i i Ss Q pe r 2 Remove the fan motor housing _ If your fan is to replace an existing ceiling assembly from the protective plastic light fixture turn electricity off at the main bag Place the fan assembly into the fuse box at this time and remove the exist lower foam pad with the bottom of the ing light fixture motor facing up The lower foam pad serves as a holder for the fan during the first stages of a WARNING assembly _ Turning off wall switch is not suffi cient To avoid possible electrical General shock be sure electricity is turned off at the main fuse box before wiring All Your Emerson ceiling fan comes supplied wiring must be in accordance with with a Fan Light Remote Control which National and Local codes and the ceil consists of a remote control transmitter ing fan must be properly grounded as and a remote control receiver mounted a precautio
11. ure there are no wires pinched between the light kit plate and the fan motor housing assembly l NOTE If no light kit is to be used on the 18 Remove one of the fan motor housing ceiling fan disregard Steps 4 and 5 proceed to How to Disassemble Your Light Kit for Cover Plate Assembly Only then continue to Step 6 1 4 20 x 11mm PAN HEAD SCREW 2 per flange FLANGE MOTOR HUB assembly screw retain for later use Position the light kit plate on the fan motor housing assembly aligning the keyhole slots over the fan motor screws Rotate the light kit plate clock wise to engage the screws into the key hole slots Reinstall the previous removed screw Tighten the three screws to secure the light kit plate to the fan motorfousing Figure 7 MOTOR SCREW 3 LIGHT KIT Figure 7 L16 O17 NOTE If you have an eight foot ceiling you will have to use the 6 downrod Carefully remove the fan assembly from the lower foam pad Turn the fan assembly over and position it on the lower foam pad with the light kit plate resting on the pad so that the top of A WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tight ened Failure to verify that the pin and setscrews are properly installed as shown in Figure 9 could result in the fan falling the motor faces up Remove the hanger ball by loosening the setscrew in the hanger bal
Download Pdf Manuals
Related Search