Illumine CLI-EMM027659 Installation Guide
Contents
1. 4 How to Wire Your Ceiling Fan If you fee that you do not have enough electrical wiring knowledge or experlence have your fan installed by a licensed electrician 1 Temporarily hang the fan motor assembly onto the ceiling mounting plate hook using the radial slot nearest the circular hole Figure 3 2 Connect the green grounding wires from the fan motor assembly and the ceiling mounting plate to the supply green grounding conductor this may be a bare wire or wire with green colored insulation Securely connect wires with wire connector supplied NOTE If you are using an Emerson Light Fixture with your fan see the Light Fixture Owner s Manual for wiring 3 Connect the fan motor assembly white wire to the supply white neutral wire using a supplied wire connector Figure 4 4 Securely connect the fan motor black wire to the supply black hot wire using wire connector supplied 5 Cap the blue fan wire with a wire connector if using the supplied wall control Figure 4 6 After connections have been made turn Jeads upward and carefully push leads into the outlet box with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box 4 WARNING To avoid risk of fire or shock check to see that all connections are tight including ground and that no bare wire is visible at the wire connectors except for the ground wire Do not operate fan u2. Emerson or any other brand of contro not specifically approved for this fan WARNING This product Is designed to use only those parts supptied with this product and or any accessorles designated specifically for use this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson could result in personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades NOTE All setscrews must be checked and re tightened where necessary before installation ee DATE CODE The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep it in a safe place for future use 1 Unpacking Instructions A WARNING Do not install or use fan If any part is damaged or missing Aa WARNING This product Is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal Injury or property damage 1 Check to see that you have received the following parts NOTE If you are uncertain of part descri
3. fan wire located on top of the motor assembly must be connected to a second HOT supply wire that Is not attached to the supplied wall control See your Emerson dealer for optional remote control options that can control the fan and accessory light kit using a single HOT supply wire 14 Position the switch housing assembly on the switch housing plate and align the holes in the switch housing assembly with the holes in the plate Secure the switch housing assembly by reinstafling the four screws removed previously Figure 13 J SWITCH HOUSING 44 MOUNTING SCREW 4 SWITCH HOUSING CONNECTOR MOUNTING SCREWS SWITCH HOUSING ASSEMBLY Figure 13 1 All fans are shipped from the factory with the reversing switch positioned to circulate air downward If airflow is desired in opposite direction turn your fan off and wait for the blades to stop turning then slide the reversing switch to the opposite position and turn fan on again Figure 14 2 The fan blades will turn in the opposite direction and reverse the airflow 3 You have now completed the assembly of your new ceiling fan Reverse Switch information Season Rotation Direction Switch Position Summer Counter Clockwise Left Winter Clockwise Right Figure 14 7 Wall Control Installation This control is designed to operate only one ceiling fan and not an accessory light kit This wal contro is rated for 1 2 amps at 120 volts
4. remove the existing light fixture Your Emerson ceiling fan comes supplied with a Fan Remote Control which consists of a wall mounted switch which allows you to regulate your ceiling fan speed IMPORTANT Your ceiling fan will not function properly and may be damaged if used with any wall dimmer switch or control other than the Emerson Electric Fan Lignt Remote Control supplied with the fan 4 WARNING To avoid fire or shock follow all wirlng Instructions carefully Any electrical work not described in these instructions should be done or approved by a licensed electrician 3 How to Hang Your Ceiling Fan WARNING Turning off wall switch Is not sufficient To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring Ali wiring must be in accordance with National and Local codes and the celling fan must be properly grounded as a precaution against possible electrical shock If you feel that you do not have enough electrical wiring knowledge or experlence have your fan instalied by a licensed electrician 44 WARNING The fan must be hung with at least 7 of clearance from floor to blades Figure 1 4s WARNING The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs Use only a ULL outlet box listed as Acceptable for Fan Support of 22 7 kg 50 Ibs or less 4 WARNING To reduce the risk of fire electric shock o
5. 32 x 3 4 screws provided 7 Position the faceplate provided onto the speed control Using the two 6 32 x 1 4 screws screw the faceplate and speed control to the wall outlet box Figure 17 8 Restore power at the main fuse box or circuit breaker panel 10 Wi SWITCH BOX TO FAN MOTOR LOAD MOTOR LOAD 1 2 AMP MAXIMUM gam Figure 16 TO 120VAC SOURCE HOT OUTLET BOX FAN CONTROL 6 32 x 3 4 SCREW 2 FACEPLATE 6 32 x 1 4 SCREW 2 Figure 17 Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan Here are a few tips to ensure quality and product performance Choosing the Appropriate Mounting Location Ceiling fans should be installed or mounted in the middle of the room and at least 7 feet above the floor and 18 inches from the walls If ceiling height allows install the fan 8 9 feet above the floor for optimal airflow Consult your Emerson Retailer for optional mounting accessories 8 Energy Efficient Use of Ceiling Fans Using the Ceiling Fan Year Round in the summer use the ceiling fan in the counter clockwise direction The airflow produced by the ceiling fan creates a wind chill effect making you feel cooler Select a fan speed that provides a comfortable breeze lower speeds consume less energy In the winter reverse the motor and operate the ceiling fan at low speed in the clockwise direction This produces a gentle u
6. ASHER 3 ASSEMBLY Figure 5 LOOSEN TWO OPPOSING 10 24 x 3 8 SCREWS PX REMOVE TWO OPPOSING 10 24 x 3 8 SCREWS FAN CEILING MOUNTING PLATE FAN MOTOR ASSEMBLY Figure CEILING TRIM RING FAN HOUSING COVER Figure 7 7 Position the fan housing cover over the fan motor assembly Align and rotate the housing to engage the two slotted holes of the fan housing cover with the two loosened screws heads in the ceiling mounting plate Securely tighten both 10 24 x 3 8 pan head screws Figure 8 8 Reinstall the previously removed 10 24 x 3 8 pan head screws to lock the housing cover onto the ceiling mounting plate Figure 8 9 Push the trim ring upwards and rotate so that it engages and locks onto the four mounting screw heads of the fan housing cover Figure 9 10 Mount the blade flanges to the fan blades using three 10 24 x 5 16 washer head blade screws per blade supplied Figure 10 Repeat for the four remaining blades WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades 11 Attach one blade assembly to the motor using the two 1 4 20 x 9 16 captive flange screws with lockwashers provided for each flange Figure 11 Make sure the screws are tightened securely Repeat this procedure for the other four blade ass
7. NOTE The 0 position is OFF The four fan speeds are selected by sliding the bar to the other four speed positions 1 2 3 and 4 A WARNING Turning off wali switch is not sufficient To avoid possible electrical shock be sure electricity Is turned off at the main fuse box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock 4 WARNING To avoid fire or shock follow alf wiring instructions carefully Any electrical work not described in these Instructions should be done or approved by a licensed electrician NOTE Electric connections should be in accordance with the Natlonal Electrical Codes and all Local Codes Before startling disconnect power to the circuit at the fuse box or circuit breaker panel 1 Remove the faceplate and screws from the existing wall switch Pull switch out from wall outlet box 2 Disconnect wires from existing fan wall switch Figure 15 3 Slide the fan control in the OFF position 0 4 Connect one BLACK wire from the fan contro to the fan motor lead with a wire connector provided Figure 16 5 Connect the other BLACK wire from the fan contro to the 120VAC hot wire with a wire connector provided NOTE Use wire connectors supplied to secure electrical connections 6 Attach the fan control to the wall outlet box with two 6
8. READ AND SAVE THESE INSTRUCTIONS Ceiling Fan Owner s Manual Net Weight 18 3 Lbs READ AND SAVE THESE INSTRUCTIONS A WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING a Use this unit only in a manner intended by the manufacturer If you have questions contact the manufacturer b Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel 1 Read your owner s manual carefully and keep it for future reference 2 Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the celling fan before servicing 3 Do not put anything into the fan blades while they are turning 4 Do not operate reversing switch until fan blades have come to a complete stop Additional Safety Instructions for Installation 1 To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades 2 All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 2014 and Local Electrical Codes Use the National Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precauti
9. al injury or property damage
10. emblies NOTE Take care not to scratch the fan housing when installing the blade assemblles 5 Ceiling Fan Assembly continued TIGHTEN TWO OPPOSING 10 24 x 3 8 PAN HEAD SCREWS FAN CEILING MOUNTING PLATE SA REINSTALL THE TWO PREVIOUSLY REMOVED 10 24 x 3 8 PAN HEAD SCREWS FAN HOUSING COVER Figure 8 MOUNTING SCREW HEADS CEILING TRIM RING FAN HOUSING COVER Figure 9 10 24 x 6 16 WASHER HEAD BLADE SCREW 3 FAN BLADE BLADE mee Figure 10 1 4 20 x 9 16 CAPTIVE FLANGE SCREW WITH LOCKWASHER 2 sets per flange SWITCH HOUSING Figure 11 MOUNTING PLATE HOLE 5 Ceiling Fan Assembly continued 12 Engage the connector of the switch housing assembly with the fan motor assembly connector Figure 12 The two connectors are keyed and color coded and must be mated correctly color to color before they can be engaged Make sure the connector latch closes properly 13 Remove the four switch housing assembly mounting screws from the switch housing plate and retain for future use Figure 12 NOTE To install an accessory light kit remove switch housing and make light kit electrical connections to blue and white leads marked For Light in the switch housing Follow light kit instructions for wiring and installation Then reinstall switch housing as outlined above NOTE The supplied wall control can not be used to control the operation of an accessory light kit The blue
11. ft 14 50 100 ft 12 _ 4 WARNING __ Before assembly your ceiling fan refer to sectlon on proper method of wiring your fan page 6 if you feel you do not have enough wiring knowledge or experience have your fan installed by a licensed electrician 2 Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit 4 WARNING Turning off wall switch is not sufficient To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock The ceiling structure must be capable of reliably supporting at least 50 pounds CAUTION To reduce the risk of electrical shock disconnect the electrical supply circuit before installing the fan light kit or receiver 44 WARNING To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support of 22 7 kg 50 Ibs or less and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt lf your fan is to replace an existing ceiling light fixture turn electricity off at the main fuse box at this time and
12. ntil blades are in place Noise and fan damage could result HOOK CEILING Vx RADIAL SLOT MOUNTING OOK HOLE PLATE Hot lay ASSEMBLY Figure 3 OUTLET BOX e FAN MOTOR SUPPLY IE 3 BLACK WIRE 2 Sa UBTOR EAN MOTOR f A BLACK WIRE WHITE WIRE eager tee Ny SUPPLY WHITE WIRE SUPPLY P fy GREEN WIRE j Figure 4 FAN MOTOR ASSEMBLY 5 Ceiling Fan Assembly 1 Remove the 10 24 x 3 8 pan head screw with lockwasher nearest the hook from the ceiling mounting plate and retain for later use Loosen the remaining two 10 24 x 3 8 pan head screws several turns 2 While still attached to the ceiling mounting plate hook pivot the fan motor assembly upwards and mate it up against the ceiling mounting plate Align and rotate the motor assembly to engage the two keyhole slots with the two loosened screw heads Figure 5 3 Securely tighten both 10 24 x 3 8 pan head screws Figure 5 4 Reinstall the previously removed 10 24 x 3 8 pan head screw with lock washer to lock the motor assembly onto the ceiling plate Figure 5 5 Loosen two opposing 10 24 x 3 8 pan head screws and remove the two remaining 10 24 x 3 8 pan head screws from the outer rim of the ceiling mounting plate Figure 6 6 Slide the fan housing trim ring over the fan housing cover Figure 7 Be sure to position the flat surface upwards towards the ceiling KEY HOLE SLOT 10 24 x 3 8 PAN HEAD SCREW WITH LOCKW
13. on agalnst possible electrical shock Electrical Installation should be made or approved by a licensed electrician 3 The outlet box and Joist must be securely mounted and capable of rellably supporting at least 50 pounds Use only U L outlet boxes listed as Acceptable for Fan Support of 22 7 kg 50 Ibs or less and use the Safety Instructions mounting screws provided with the outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electriclan if in doubt 4 The downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for an 8 foot ceiling 5 The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades 6 Follow the recommended instructions for the proper method of wiring your celling fan If you do not know enough about electrical wiring have your fan installed by a licensed electrician WARNING To reduce the risk of electrical shock this fan must be installed with an isolating wall control switch NOTE This fan Is suitable for use with solid state speed controls WARNING To reduce the risk of fire or electrical shock this fan should only be used with fan Speed control Model No SW46 U L Model No UC9020 manufactured by Rhine Electric Co Ltd WARNING To avold fire shock or injury do not use an
14. pdraft which forces warm air near the ceiling down into the occupied space Remember to adjust your thermostat when using your ceiling fan additional energy and dollar savings could be realized with this simple step Turn Off When Not In the Room Ceiling fans cool people not rooms If the room is unoccupied turn off the ceiling fan to save energy IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan Periodic cleaning of your new ceiling fan is the only maintenance that is needed When cleaning use only a soft brush or lint free cloth to avoid scratching the finish Abrasive cleaning agents are not required and should be avoided to prevent damage to finish 44 WARNING Do not use water when cleaning your ceiling fan It could damage the motor or the blades and create the possibility of an electrical shock 10 Accessories 1 Ceiling Fan Light Kits see store or catalog 2 Ceiling Fan Light Controls see store or catalog 3 Ceiling Fan Blades see store or catalog 4 WARNING The use of any other control not specifically approved for this fan could result in fire shock and personal injury 11 4 WARNING This product is designed to use only those parts supplled with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in person
15. ption refer to exploded view Hlustration HARDWARE CONTENTS Part Description Quantity 10 24 x 5 16 Washer Head Screws 1 4 20 x 9 16 Captive Flange Screw with Lockwasher spare 8 32 x 5 16 Switch Cup Screw spare CE Wire Connectors 4 10 24 x 3 8 Pan Head Screw spare 1 4 10 24 x 3 8 Pan Head Screw re with Lockwasher spare 1 PACKAGE CONTENTS Part Quantity e engm rae D rnos Switch Housing Assembly 4 Speed Slide Wall Control with Hardware Description NOTE Place the parts from the loose parts bags in a small container to keep them from being lost If any parts are missing contact your local retailer or catalog outlet for replacement before proceeding 2 Remove the fan assembly from the protective plastic bag Place the fan assembly into the upper foam pad with the lead wires facing up The upper foam pad serves as a holder for the fan during the first stages of assembly 1 Unpacking Instructions This Manual Is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One stepladder One 1 4 blade screwdriver One wire stripper Materials Wiring outlet box and box connectors must be of type required by the local code The minimum wire would be a 3 conductor 2 wire with ground of following size Wire Size A W G Up to 50
16. r personal injury mount fan to outlet box marked Acceptable for Fan Support of 22 7 kg 50 Ibs or less and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt CAUTION To reduce the risk of electrical shock disconnect the electrical supply clrcuit before installing the fan light kit or receiver NOTE Make all wiring connections using wire connectors supplied Make sure that all connections are tight Including ground and that no bare wire is visible at the wire connectors except for the round wire 1 Disconnect electrical power to the branch circuit at the circuit breaker or fuse box before attempting to install the ceiling fan mounting plate on the outlet box 2 Pull the electrical supply black white and ground wires through the center opening of the ceiling mounting plate before securing the plate to the outlet box as shown in Figure 2 3 Position the ceiling mounting plaie onto the outlet box and secure using the two outlet box screws supplied with outlet box Figure 2 CEILING 7 AT Th Figure 1 CEILING MOUNTING bea CEILING MOUNTING PLATE HOOK OUTLET BOX Figure 2 SCREWS 2 WARNING To avold possible fire or shock make sure that electrical wires are not pinched between the celllng mounting plate and the fan motor assembly
Download Pdf Manuals
Related Search