Hunter 59013 Use and Care Manual
Contents
1. See page 4 for details Ey Longer Downrod for ceilings 10 feet or higher Check box to see A fan weight Assess ceiling angle Select a downrod length 2 M3522 01 05 14 14 Hunter Fan Company www HunterFan com 1 888 830 1326 Read and Save These Instructions This product conforms to UL Standard 507 A WARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel w 3 To reduce the risk of fire electrical shock or motor damage use only Hunter Speed Controls w 4 To reduce the risk of personal injury do not bend the blade brackets when installing the blade brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades CAUTIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician c 2 Use only Hunter replacement parts2. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Tools Needed www HunterFan com 1 888 830 1326 amp LI Ladder L Pliers L Wire Strippers E Power Drill 9 64 Drill Bit optional optional If mounting to a support structure you will also need these tools M3522 01 05 14 14 Hunter Fan Company 3 4 CEILING 4a ii Mounting Options www HunterFan com 1 866 268 1936 4 e ka ea ra ka ea a a e o N ea ra o o l O i egoe U p If you have a flat ceiling Hang your fan by a standard downrod included Standard Support Support Mounting Structure T O If you have an angled ceiling InN 0 1 You will need a longer downrod sold separately Outlet Box 2 If your ceiling angle is greater than 34 you will Angled Cellin required also need an Angled Mounting Kit sold separately Mounting N Outlet o required Mounting Use the three steps below to determine if your ceiling angle is greater than 34 Use Standard Mounting Use Angle
3. Hunter Fan Company www HunterFan com 1 888 830 1326 If you are installing multiple remote controlled fans on the same circuit breaker you may need to perform a few extra steps to prevent interference or faulty operation of your remote controls Go to www HunterFan com FAQs and click How do properly install multiple remote controlled fans for more information Downrod www HunterFan com 1 888 830 1326 Standard Downrod skip to next page for ceilings 8 10 high If you need a different downrod length follow these steps Longer Steps 1 5 to remove standard downrod pipe Downrod for angled ceilings or ceilings 10 or higher Included pre assembled Shorter Downrod for fans installed close to ceiling Included Sold Separately Steps 6 10 to reassemble with new pipe M3522 01 05 14 14 Hunter Fan Company Downrod continued www HunterFan com 1 888 830 1326 T U YN O O Remove the pre installed setscrew so that the downrod can be inserted Hand tighten the downrod at The wires can be cut but Tighten the setscrew least 4 5 full turns until it stops leave at least 8 extending with pliers DO NOT from the top of the downrod HAND TIGHTEN If the setscrew is not tightened securely the fan may fall M3522 01 05 14 14 Hunter Fan Company Downrod continued MI ec ee ee
4. is on e Tighten all of the blade and e Tighten the blade and blade l blade iron screws until they iron screws until they are snug Pull the pull chain to make sure are snug it is on Check to see if any of the Turn the power off support blades are cracked If so replace Push the motor reversing switch the fan carefully and check all of the blades firmly left or right to ensure that that the hanger ball is it is engaged properly seated Check the circuit breaker to Use the provided balancing ensure the power is turned on kit and instructions to balance Make sure the blades spin freely the fan Turn off power from the circuit breaker then loosen the canopy and check all the connections Remote control of fan is erratic If you have multiple remotes or according to the wiring diagram multiple remote controlled fans on page 10 installed on the same circuit breaker and you are experiencing Check the plug connection in Install a fresh battery interference or faulty operation of the switch housing your remote controls please go to www HunterFan com FAQs and click How do properly install multiple remote controlled fans e Install a fresh battery for information on how to correct this issue e Make sure the battery is installed correctly Transmitter only works when held at close range M3522 01 05 14 14 Hunter Fan Company
5. Table of Contents Congratulations on purchasing your new Hunter ceiling fan It will provide comfort and performance in your home or office for many years This installation and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world To register your fan please visit www HunterFan com register Save your receipt for proof of purchase Blades What to Expect with Your Installation Tools Needed Light Kit AY M3522 01 05 14 14 Hunter Fan Company www HunterFan com 1 888 830 1326 Ceiling Bracket Mounting Options Operation Maintenance amp Cleaning Troubleshooting What to Expect with Your Installation AS Ss J If you are unfamiliar i 2 with wiring use a qualified electrician f gt Fy 30inches Qi aa a Ji from blade tip _ A YQ o ga a oS from bottom edge of blade Must be able to to the floor secure the fan to building structure or A fan rated outlet box Know your wiring Assess location for ceilings 8 10 feet high You may need a friend to help you AN Standard Downrod i h Shorter Downrod Ceiling angles greater 7 v a for fans installed close to ceiling than 34 will require an Angled Mounting Kit
6. d Mounting BOTH Ceiling amp Wall or Low Profile Mounting to hang the fan from a You need ONLY to hang the fan from a flat ceiling vaulted or angled ceiling a Longer Downrod most common Mounting Kit M3522 01 05 14 14 Hunter Fan Company Ceiling Bracket Make sure all four 4 bumpers are still attached To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location www HunterFan com 1 888 830 1326 Use wood screws Use machine screws included when securing provided with outlet to support structure with box when securing to approved electrical outlet existing ceiling fan rated box Drill 9 64 pilot holes outlet box Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware foundin support of 31 8 kg 70 Ibs the gt hardware bag or less M3522 01 05 14 14 Hunter Fan Company For angled ceilings point opening toward peak If you are unable to do this call Technical Support at 1 888 830 1326 Refer to warning w 1 on pg 2 Ceiling Bracket continued Preparation Remove the shipping blocks from the motor Discard the screws Note Some fans will have a shipping ring instead of shipping blocks Please remove the ring and discard the screws M3522 01 05 14 14
7. e bag connect the black wire ungrounded from the ceiling to the black wire from the receiver Connect the white wire grounded from the ceiling to both the white wire from the receiver and the white wire from the fan papunosbun papunosb ay4ym 2 Om RECEN Turn the splices upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box www HunterFan com 1 888 830 1326 Position the canopy so that when Lift the canopy into place so that Insert the two canopy screws lifted into place the canopy fits into the screw holes are aligned found in the hardware bag the hanging bracket as shown Note Fan style may vary f M3522 01 05 14 14 Hunter Fan Company q Blades www HunterFan com 1 888 830 1326 Install the grommets found in the W hardware Lightly attach the blade irons to the bag in the blades by hand Place each blade motor with screws found in between a blade iron and medallion Install three the X hardware bag then securely blade screws found in the A hardware bag to tighten after both screws are attached attach the medallion to the blade iron Repeat nit or bede Your blades are shielded with Dust Armor which is a nanotechnology coating that repels dust For cleaning the fan use s
8. ee eae ee a el El i Yer a ma ee E ewe SSeS S LA A YE ik i Put the wires and downrod through the canopy Let the canopy sit loosely on top of the fan DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES Place the downrod ball into the slot in the ceiling bracket M3522 01 05 14 14 Hunter Fan Company www HunterFan com 1 888 830 1326 Note Fan style may vary MO u 16 Buipuno16 du s green yellow stripe Using an orange wire connector from the amp hardware bag connect the 3 grounding wires green green yellow stripe or bare copper coming from the ceiling downrod and hanging bracket Refer to CAUTION c 1 on pg 2 d s MO u 16 A 4 clockwise until tight Note To connect the wires hold the bare metal leads together and place a wire connector over them then twist Using the orange wire connectors from the remote control hardware bag connect the blue wire from the receiver to the blue wire or possibly black with white stripe wire from the fan Connect the yellow wire from the receiver to the black wire from the fan y ey sat M3522 01 05 14 14 Hunter Fan Company www HunterFan com 1 888 830 1326 M CEIL SSi 4219 Using the orange wire connectors from the x hardwar
9. nsert and tighten the If it does not turn off power to your screws Do not over tighten AE N l minute eee aoe Quickly press the Light button to aes eis Wier ni dn TNT ens turn the lights off and on fans repeat this process for each fan M3522 01 05 14 14 Hunter Fan Company ON Operation Maintenance amp Cleaning continued Safe Exit The Safe Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out To use Safe Exit e Press the Fan Off button for at least three seconds to initiate the Safe Exit Mode e The lights will flash for visual P Reverse confirmation Switch e The lights will stay on 50 brightness for 15 seconds and then begin to dim After a total of 30 seconds the lights will be completely off Note For CFL lighting the lights will stay on 100 brightness for 30 seconds After a total of 30 seconds the lights will be completely off To switch the direction of air flow move the reverse switch to the opposite position You will need to remove the light kit glass to do so M3522 01 05 14 14 Hunter Fan Company www HunterFan com 1 888 830 1326 For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning products may damage the finishes Troubleshooting www HunterFan com 1 888 830 1326 Fan doesn t work Excessive wobbling Noisy Operation e Make sure power switch
10. nto the sockets When necessary replace with bulbs of same wattage Note Globe style and number of l lights may vary Lift the globe and align the notches in the globe with the tabs in the light kit Attach the glass bowl to the light kit by twisting it clockwise until it snaps into place M3522 01 05 14 14 Hunter Fan Company www HunterFan com 1 888 830 1326 See next page for fan operation instructions Operation Maintenance amp Cleaning www HunterFan com 1 888 830 1326 High Medium Low Fan Off Battery Door Light High Phillips Fan Off Head Screw To access the battery compartment Note The remote must be paired The Fan Off button only turns the To install the transmitter cradle remove the small Phillips head screw before the fan will operate fan off To turn the fan on press one remove the two screws holding that secures the battery door to the Within 3 minutes of restoring power of the fan speed buttons your switch cover plate Do not transmitter assembly The battery to the fan press both the Fan Off remove the cover plate Orient should be installed with the positive button and the High button for at ete on the cradle by lining up the two side up Replace with a CR2032 least 4 seconds Your fan will turn on oo Medium mounting holes with those on the battery when necessary low to indicate successful syncing ot LOW cover plate I
11. oft brushes or cloths to prevent scratching Cleaning agents may damage the finishes M3522 01 05 14 14 Hunter Fan Company Switch Housing Screw two housing assembly screws K from the hardware bag halfway into the motor housing It does not matter which two screw holes you choose Make sure the upper switch housing is securely attached to the mounting plate Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling t Feed the wire plug through the center hole of the upper switch housing then wrap keyhole slots around the screws and twist counterclockwise M3522 01 05 14 14 Hunter Fan Company www HunterFan com 1 888 830 1326 Insert the third screw found in the hardware bag into place and then tighten all three screws Light Kit Connect the plugs from the upper and lower switch housings Make sure to line up the colored markings on the connectors www HunterFan com 1 888 830 1326 Place the light kit over the upper switch Install three housing screws found housing and align the screw holes in the hardware bag Tighten all three screws securely Make sure the lower switch housing is securely attached to the upper switch housing Failure to properly secure all three assembly screws could result in the light fixture falling M3522 01 05 14 14 Hunter Fan Company Light Kit continued Install the included CFL bulbs i
Download Pdf Manuals
Related Search