Sea Gull Lighting 31751-758 Installation Guide
Contents
1. INSTALLATION AND SAFETY INSTRUCTIONS WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU Carefully remove the fixture from the carton and check that all ARE WORKING ON IS SHUT OFF EITHER THE FUSE IS parts are included as shown in Figure 1 and 2 Be careful not to REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF misplace any of the screws or parts which are needed to install this fixture GENERAL STEP 1 You don t need special tools to install this fixture Be sure to you are unclear as to how to proceed consult a qualified electrician STEP 2 Thread top assembly L onto fixture body N Gently pull wire through top assembly Thread fixture loop I to top assembly L C s AA N OUTLET BOX Gently pull excess wire through fixture loop D O S AV FSS lt WIRE CONNECTORS STEP 3 N r GROUND WIRE Thread bottom assembly K onto fixture body lt MOUNTING BAR A GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX OUTLET BOX KO SCREWS GROUND WIRE lt GROUND WIRE F WIRE SCREW COLLAR E CONNECTORS CANOPY H SCREW COLLAR RING G BAR A A OUTLET BOX CHAIN S SCREWS GROUNDING SCREW D FIGURE 2 NOT INCLUDED TOP ASSEMBLY L SHADE P a si FIXTURE BODY CANDLE COVER sea guli ighting mse i Installation And BOTTOM Safety I nstructi on IN pon ASSEMBLY K H C _ 8 2 1 OER PO Noron Line art shown may not exactly match the fi2. nd the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manu factured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box and then raise the canopy H against ceiling and screw the screw collar ring G to the screw collar E STEP 2 Slip candle cover J over socket for each arm STEP 3 Install lamps STEP 4 Install shade P and or glass over sockets and secure with retain ing ring whichever is applicable CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
3. wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE e TTC PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED QW eS SS Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 6 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire F from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A If uninsulated wire is on the mounting bar A connect the ground wire F from the fixture if Supplied a
4. xture enclosed However the installation instructions do apply to this fixture WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY MOUNT TO OUTLET BOX Fill In Item Number On Carton And OR SUPPORTING SYSTEM ABLE TO SUPPORT THE File This Sheet For Fixture Reference ITEM WEIGHT OF THE FIXTURE INSTALLATION HC 821 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that three threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Attach screw collar E to nipple C STEP 2 Using two pairs of pliers open one link of chain S and connect it to the fixture loop I at the top of the fixture STEP 3 Lace wires up through chain S and pass wires through holes in screw collar E We recommend lacing wire up through every other link of chain S Note If your fixture comes with 2 screw collar STEP 4 rings Select the one of your choice Slide the screw collar ring G and canopy H in that order over chain S Open one link on the top of the chain S and attach it to the screw collar E which has been mounted to the ceiling nip ple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 5 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the
Download Pdf Manuals
Related Search