Insteon 2475F Use and Care Manual
Contents
1. Certification This product has been thoroughly tested by ITS ETL SEMKO a nationally recognized independent third party testing laboratory The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U S and Canadian device safety standards that the manufacturing site has been audited and that the manufacturer has agreed to a program of quarterly factory follow up inspections to verify continued conformance FCC amp Industry Canada Compliance Statement This device complies with FCC Rules Part 15 and Industry Canada RSS 210 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference including interference that may cause undesired operation of the device Le present appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autorise aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radiolectrique subi mme si le brouillage est susceptible den compromettre le fonctionnement The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful in2. fixture fan wire with a wire nut 9 Connect FanLinc blue wire to the fixture light wire if fixture does Fan not have a light cap the blue wire 10 Connect FanLinc black wire to line with a wire nut 11 Ensure all connections are secure with no exposed copper 12 Turn breaker back on FanLinc light LED turns green FanLinc fan LED turns red Page 4 of 12 2475F Rev 2 20 2014 8 33 AM i Optional test by tapping set button a few times Light will toggle between green on and red off ii Optional cover LEDs with black electrical tape to avoid unwanted LED glow at night which may be visible with some fan cowlings 13 While software is highly recommended to manage this hidden device if you wish to set up any scenes in FanLinc using the set buttons it is critical that you do so now See INSTEON scenes 14 Carefully remount cowling with FanLinc inside or in electrical box Use cable tie included to secure FanLinc to fan bracket Align cable tie with the notch on the FanLinc case ensuring that cable tie and wires will not interfere with any moving parts INSTEON Setup INSTEON remote control is done using scenes Scenes allow you to instantly recall favorite lighting and appliance settings at the touch of a button or in response to central control or even a sensor Each scene has at least one controller and at least one responder Simple scenes can be setup using the instructions below Make Fan a
3. to re create it For simplicity sake the steps below do not cover the removal or re installation of the ceiling fan 1 Use pull chain to turn fan motor off 2 Tap controller scene button 3 Press amp hold controller set button until it beeps Controller LED will start blinking 4 Press amp hold controller set button until it beeps again Controller LED will continue blinking 5 Press amp hold fan or light set button until it double beeps Controller LED will stop blinking 6 Temporarily hang the fan from the mounting ring so the fan can spin safely and without obstruction i Move safely clear of the fan blades 7 Test by turning scene on and off from controller LED and Beeper Behavior LEDs Fan LED Green blink slow Setup set scene speed to slow Green blink medium Setup set scene speed to medium Green blink fast Setup set scene speed to fast 1 For devices without beepers hold until its LED begins blinking this may take 10 seconds Page 6 of 12 2475F Rev 2 20 2014 8 33 AM Red on Setup set scene speed to off Green on Fan is on Red on Fan is off Light LED Blinking green Setup Awaiting X10 address Blinking red Setup Awaiting X10 address removal Green Light is on Red Light is off Beeper Beeper Single beep Enter setup Mode or transition to next setup Mode Double beep Setup successful return to Ready Mode 35 ap Return to Ready Mode e
4. 11 FCC amp Industry Canada Compliance Giatement teer tsen tetr tntr nssr nssrnntnnnnssrnnnnssrnsnrnnnns 11 Limited Watt anty EE 11 LAMITATONS EE 12 Page 2 of 12 2475F Rev 2 20 2014 8 33 AM About FanLinc FanLinc is designed to easily incorporate both fan speed and light control within your INSTEON network It is a dual load responder simultaneously acting as a light fixture dimmer plus a 4 speed fan controller off low medium amp high Control from any INSTEON controller such as KeypadLinc Mini Remote RemoteLinc 2 and software Lights blue Fan red fe Line black E Fan YY j Ee status LED Neutral white Set button Set button Light fan lights status LED Features amp Benefits 4 Speed fan controller off low medium amp high 300 Waitt Incandescent Dimmer X10 Compatible 1 address for light 1 address for fan Dual band repeater and access point Designed to fit inside most ceiling fan cowlings Dual set buttons amp LEDs and a beeper for simple setup All settings retained through power outages 2 year Warranty What s in the Box FanLinc Wire nuts 1 cable tie Quick Start Guide Page 3 of 12 2475F Rev 2 20 2014 8 33 AM Installation CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference FOR CEILING FANS ONLY FanLinc is intended for installation in accordance with the National Ele
5. FanLinc INSTEON Remote Control Light amp Fan Controller Dual Band Owners Manual 2475F Page 1 of 12 INSTEON 10 2014 8 33 AM ADOUT Fan Line iis svcccececicsdects is i ccie nbs echo eee sas EEEE E 3 Features amp Bement rorarii anaran eE AEAN AEEA tucsanctuedencs apuctunt tuesentuecusscdtvedsncs acastuneceste ttueeesets 3 Whats mihe B schdref chte Eech dantdeeaasebtedas bdibaasbidatasactetndastdevens 3 Installat ico oe ceed cas ee E EE E 4 Identifying the Electrical Wires in your Home 4 INSTEON SCOM CS eege geess araoa EE svete aa aaah Gaa aaide A aaa Aeka aE aaaea 5 Make Fan an INSTEON PHesponder 5 Make Light an INSTEON Besponder 5 Remove FanLinc from a Scene as a Responder sseesssessieesrresrnesrrssrnssrnssrnssinsstnssrnsstnsstnnstnnttnnnnnnnnnn nt 6 LED and Beeper Behavior ccccseecceccsseeeceesseeeeeenseeeeeensneeeeenseeeeeensueeeeensueeeeensueeeeensueeeeensueeeesneeeeeenseaeeeesses 6 Elek e Ee DEE eege 6 EE rep Re eR TPE e ee ee TEEPE Creer CHE een ERE ere err eee rere eer ere renee e 7 Advanced Features eer 7 Software End ue EE H Using FanLinc as a Phase Bridge ccceeeeseceeeenneeeeeeaeeeceeaaeeeeeeaaeeeeeeaaeeeeeeaaeeeseeaaeeeeeeaaeeeseeaaeeeeseaeeeeneaas 7 Add an XITO Ae E 8 SIE 8 pell heess 8 TOUDIESHOOUNG ii eege ee EE EE 10 Certification and Warranty si ccciccccccccesccceseecececescacsezien cesceeteatcesuscceseterinteesteeceedeetestaeececeseces enaetieneesccceeenee 11 E ee EE
6. L x 50 8mm W x 22 2mm D Weight 22g 0 05 Ib Operating Environment Indoors Electrical Retains all settings without power Yes all saved in Non volatile EEPROM Voltage 120VAC Single Phase Frequency 60Hz Maximum Dimmer load 300 Watts Maximum fan load 1 Amp Safety Approved ETL Intertek Testing Services Certifications FCC IC Canada Troubleshooting Problem Possible Cause Solution FanLinc may be out of range Try moving an Access Point or installing other Dual Band devices closer to FanLinc The INSTEON signal may not be getting to the vicinity of responder FanLinc won t add as a Scene responder Large appliances such as refrigerators or air conditioners may be producing electrical noise on the power line Other electrical devices such as computers televisions or power strips may be absorbing the INSTEON signal Make sure phases are bridged add additional INSTEON devices and or move around existing INSTEON devices Install a power line noise filter e g 1626 10 to filter electrical noise and minimize signal attenuation Ramp Rate may be extremely slow Add to scene again with faster Ramp Rate Pull chain on fan light is not in ON position Use pull chain to turn light on FanLinc will not turn on Controller may be added to scene in off light state Add to scene again at desired brightness Burned out bulbs Change
7. anical tampering For optimal use manually verify the device state Any home automation device should be viewed as a convenience but not as a sole method for controlling your home In no event shall Seller be liable for special incidental consequential or other damages resulting from possession or use of this device including without limitation damage to property and to the extent permitted by law personal injury even if Seller knew or should have known of the possibility of such damages Some states do not allow limitations on how long an implied warranty lasts and or the exclusion or limitation of damages in which case the above limitations and or exclusions may not apply to you You may also have other legal rights that may vary from state to state Protected under US and Foreign Patents see www insteon com Copyright 2012 Smarthome 16542 Millikan Ave Irvine CA 92606 800 762 7845 www smarthome com Page 12 of 12 2475F Rev 2 20 2014 8 33 AM
8. bulbs Loose connection Controller may be sending commands to a another responder s that is no FanLinc is taking a long longer in use time to respond to scene triggers See Problem 1 Turn power off to fan assembly and recheck all connections Remove all unused responders from the controller HINT If you are using HouseLinc software you can easily check scene Membership and eliminate any unnecessary If the above doesn t work perform a factory reset on the controller Page 10 of 12 2475F Rev 2 20 2014 8 33 AM Pull chain on fan is not set to HIGH Use pull chain to set fan to highest speed setting Fan speed is too slow or does not turn on Scene speed was added on slow Remove from scene and re add at higher speed The light ig bugzinawhen The light dimming component inside The bulb filaments are vibrating Use rough service aii See 9 FanLinc chops the power line sine 130 Volt or appliance grade bulbs to reduce the wave to reduce the power noise Power cycle Turn appropriate circuit breaker off wait 10 seconds and turn back on FanLinc is no longer e S Small electrical surge or voltage spike responding g ge Sp Perform a factory reset on FanLinc and set up scenes again If you have tried these solutions reviewed this Owner s Manual and still cannot resolve an issue you are having with FanLinc please call 800 762 7845 Certification and Warranty
9. ctric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada Use indoors only FanLinc is not designed nor approved for use on power lines other than 120VAC 50Hz 60Hz single phase Attempting to use FanLinc on non approved power lines may have hazardous consequences Recommended installation practices e Use only indoors or in an outdoor rated box e Be sure that you have turned off the circuit breaker or removed the fuse for the circuit you are installing FanLinc in Installing FanLinc with the power on will expose you to dangerous voltages e Connect only copper or copper clad wire to FanLinc e FanLinc may feel warm during operation The amount of heat generated is within approved limits and poses no hazards To minimize heat buildup ensure that the area surrounding the FanLinc air vents is as clear of clutter as possible e To reduce the risk of overheating and possible damage to other equipment use FanLinc load output to control no more than 300 watts of 120VAC incandescent lamps plus no more than 1 Amp of Fan load Dimming an inductive load by connecting to the light load wire such as a fan or transformer could cause damage to the dimmer the load bearing device or both If the manufacturer of the load device does not recommend dimming use a non dimming INSTEON on off switch USER ASSUMES ALL RISKS ASSOCIATED WITH DIMMING AN INDUCTIVE LOAD e You will need a flathead sc
10. inc double beeps 1 Most models 2 If the controller does not have a beeper wait until its LED begins blinking Page 5 of 12 2475F Rev 2 20 2014 8 33 AM FanLinc light LED will flash once amp return to green Controller will beep beep and its LED will stop blinking 4 Confirm the scene addition was successful by tapping on off on your scene controller Ceiling fan light will toggle between on and off 5 If you wish to adjust the light s scene on level and or ramp rate Adjusting on Level a Using your scene controller adjust the ceiling fan light brightness to the desired brightness for your scene b Repeat Steps 1 and 3 above Adjusting Ramp Rate a Using your scene controller adjust the light brightness to correspond with the Ramp Rate desired Brighter Faster Dimmer Slower b Double tap FanLinc light set button c Repeat Steps 1 and 3 above 6 If you wish to add FanLinc light to more scenes simply repeat these steps Remove FanLinc from a Scene as a Responder Software is recommended Note If you choose to remove FanLinc from use it is important that you remove scene memberships from all controllers Otherwise controllers will retry commands repetitively creating network delays Follow the instructions below for each scene controller that FanLinc is a member of If you have both fan and light links removing one will also remove the other If you d like to continue using the other link you ll need
11. ither after setup time out or user econd bee j initiated set button Tap Fast beeps on transition to next fan speed Advanced Features Software Only Settings The following settings are available for programming only via compatible software i e HouseLinc e Enable Disable LEDs e LED Blink on traffic e Programming Lock Using FanLinc as a Phase Bridge FanLinc automatically bridges the electrical phases in your home via communications with other dual band devices on the other phase This is only important if you have powerline only INSTEON products in your home If you are relying on FanLinc to bridge the electrical phases use the following procedure to confirm bridging 1 Tap FanLinc light set button four times quickly FanLinc will start beeping once per second FanLinc light LED will turn green 2 Check the LED behavior of other dual band devices e Ifthe other dual band device is blinking green it is on the other phase Device provides a phase bridge to FanLinc e If the other dual band device is blinking red it is on the same phase Device does not provide a phase bridge to FanLinc Relocate if necessary and practical e If the other dual band device is not blinking Device not within RF range of FanLinc Page 7 of 12 2475F Rev 2 20 2014 8 33 AM Does not provide a phase bridge to FanLinc Relocate if necessary and practical e If the other dual band device is exhibiting any
12. n INSTEON Responder Follow the steps below to add your ceiling fan to an INSTEON scene 1 Tap FanLinc Fan set button until FanLinc beeper amp LED indicate the desired fan speed FanLinc fan LED will be in the desired state see table below Tap Fan Speed Beeper LED E low Single beep Blinks Green Slow gnd medium Double beep Blinks Green medium a high Fast Double beep Blinks Green Fast 4 off None red 2 Press amp hold the scene controller set button until it beeps Controller LED will start blinking 3 Press amp hold FanLinc fan set button until FanLinc double beeps FanLinc will beep beep and the LED will return to previous state Controller will beep beep and its LED will stop blinking If you wish to add your fan to more scenes simply repeat these steps 5 Temporarily hang the fan from the mounting ring so the fan can spin safely and without obstruction Then while safely clear of the fan blades confirm the scene addition was successful by pressing on off on your scene controller FanLinc fan LED will toggle between green and red Make Light an INSTEON Responder Follow the steps below to add your ceiling fan light to an INSTEON scene 1 Press amp hold the scene controller button until it beeps Controller LED will blink 2 Tap FanLinc light set button until the ceiling fan light is on FanLinc light LED will be green 3 Press amp hold FanLinc light set button until FanL
13. nship or if the product does not perform as warranted above during the warranty period Seller will either repair it replace it or refund the purchase price at its option upon receipt of the product at the address below postage prepaid with proof of the date of purchase and an explanation of the defect or error The repair replacement or refund that is provided for above shall be the full extent of Seller s liability with respect to this product For repair or replacement during the warranty period call support at 800 762 7845 with the Model and Revision of the device to receive an RMA and send the product along with all other required materials to INSTEON ATTN Receiving 16542 Millikan Ave Irvine CA 92606 5027 Page 11 of 12 2475F Rev 2 20 2014 8 33 AM Limitations The above warranty is in lieu of and Seller disclaims all other warranties whether oral or written express or implied including any warranty or merchantability or fitness for a particular purpose Any implied warranty including any warranty of merchantability or fitness for a particular purpose which may not be disclaimed or supplanted as provided above shall be limited to the two year of the express warranty above No other representation or claim of any nature by any person shall be binding upon Seller or modify the terms of the above warranty and disclaimer Home automation devices have the risk of failure to operate incorrect operation or electrical or mech
14. other behavior or color refer to its owners manual 3 Tap FanLinc light set button FanLinc will stop beeping FanLinc light LED will turn red if light is off Other device LEDs will stop blinking Add an X10 Address For the fan 1 Press amp hold FanLinc fan set button until it beeps FanLinc LED will start blinking green 2 Send the desired X10 address plus on 3 times e g send B5 BON B5 BON B5 BON FanLinc will double beep and the LED will stop blinking 3 Test by sending the X10 address on off FanLinc fan will turn on off For the light 1 Press amp hold FanLinc light set button until it beeps FanLinc LED will start blinking green 2 Send the desired X10 address plus on 3 times e g send B5 BON B5 BON B5 BON FanLinc will double beep and the LED will stop blinking 3 Test by sending the X10 address on off FanLinc light will turn on off For other X10 setup instructions visit http www smarthome com insteon x10 programming html Factory Reset NOTE All settings and scenes will be erased 1 If possible remove all links 2 Press amp hold FanLinc light set button until it beeps LED will start blinking green 3 Press amp hold the FanLinc light set button until it beeps again LED will start blinking red 4 The following three steps must be done quickly to the FanLinc light set button a Double tap b Release c Press amp hold FanLinc will beep LEDs and light will turn off Fan me will beep fo
15. r 5 seconds 5 Release after beeping stops Light LED will turn green Light LED will turn off FanLinc will beep beep Light LED will turn green Fans light will turn on Specifications General Page 8 of 12 2475F Rev 2 20 2014 8 33 AM Product Name FanLinc INSTEON In line Dual load Module Brand Smarthome Manufacturer Product Number 2475F UPC 813922011548 FCC ID SBP2475F Warranty 2 Years Limited INSTEON Maximum Links 400 Software Configurable Yes always a RF Range Up to 100 Open Air Beeper Yes X10 X10 Support Yes X10 Addresses 2 max unassigned by default Operation Fan Controller Light Dimmer INSTEON Group 2 INSTEON Group 1 Fan speeds 4 off slow medium amp Brightness levels 32 fast Fan responds to on off fast on fast off Dimmer responds to on off fast on fast off and dim brights X10 and dim brights X10 commands commands Brightness Fan Off Off 1 49 Slow 50 99 Medium 100 Fast LED Green on LED Green on Red off Red off Setup varies Setup varies X10 1 Address unassigned X10 1 Address unassigned by default by default Mechanical Wires black line blue light red fan white neutral all 16AWG Page 9 of 12 2475F Rev 2 20 2014 8 33 AM Case Color White Plastic UV Stabilized ABS Dimensions 114mm
16. rewdriver a Phillips head screwdriver and a voltage meter to install FanLinc Identifying the Electrical Wires in your Home To install FanLinc you will need to identify the following four wires e Line usually black may also be called HOT or LIVE carries 120VAC electricity into the electrical box e Neutral usually white commonly daisy chained from box to box usually appearing as a white wire bundle e Load usually black blue or red e Ground Bare copper wire or metal fixture if grounded If you are having difficulties identifying wires consult an electrician to help you IMPORTANT e If you have any difficulties or questions consult an electrician If you are not knowledgeable about and comfortable with electrical circuitry you should have a qualified electrician install the product for you 1 Write down the INSTEON ID e g 12 34 56 for reference 2 Using your ceiling fan pull chains set fan to highest speed and turn light on note once installed FanLinc will control all fan and light functions Ss 3 Turn off the breaker remove fuse supplying power to the fan aes 4 Remove the ceiling fan from the electrical box 2 f Black 5 Identify line neutral and load lines for fan and light separately z C Bed 6 Disconnect wires from the ceiling fan and light if applicable d 7 Connect FanLinc white wire and the fixture neutral wire to the house neutral with wire nut 8 Connect FanLinc red wire to the
17. terference in residential installations This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio and television reception However there is no guarantee that interference will not occur in a particular installation If this device does cause such interference which can be verified by turning the device off and on the user is encouraged to eliminate the interference by one or more of the following measures Re orient or relocate the receiving antenna of the device experiencing the interference Increase the distance between this device and the receiver Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver Consult the dealer or an experienced radio TV technician WARNING Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Limited Warranty Seller warrants to the original consumer purchaser of this product that for a period of two years from the date of purchase this product will be free from defects in material and workmanship and will perform in substantial conformity to the description of the product in this Owner s Manual This warranty shall not apply to defects or errors caused by misuse or neglect If the product is found to be defective in material or workma
Download Pdf Manuals
Related Search