Sea Gull Lighting 77520-845 Installation Guide
Contents
1. the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES A m FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 FLUSH MOUNT After wires are connected tuck them carefully inside outlet box and then raise the fixture canopy l against ceiling allowing for mounting screws F to protrude through holes in fixture canopy 1 Secure in place with cap nuts J STEP 2 CHAIN HUNG Raise canopy O to ceiling and secure by threading screw collar ring L to screw collar H Raise shade M over center pipe P Secure in place by threading bottom lockwasher and hexnut Z and finial N CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts2. INSTALLATION AND SAFETY INSTRUCTIONS e Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off H U NG e Use of other manufacturers components will void warranty listing x WIRE CONNECTORS and create a potential safety hazard MOUNTING BAR A e f you are unclear as to how to proceed contact a qualified electrician NUT G e You don t need special tools to install this fixture niin NIPPLE C e Be sure to follow the steps in the order given CANOPY 0 e Under no circumstances should a fixture be hung on house SCREW e electrical wires nor should a swag type fixture be installed on a CANOPY COLLAR H ceiling which contains a radiant type heating system LOOP E Read instructions carefully Save these instructions SCREW COLLAR RING L CHAIN S BEFORE YOU BEGIN Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture FIXTURE LOOP B NOTE This fixture may be installed either flush mount or chain FIXTURE hung Follow the steps for the mounting method you have chosen CANOPY I FOR CHAIN HUNG STEP 1 Install fixture loop B to top center pipe P A CENTER PIPE P FOR FLUSH MOUNT STEP 1 Remove fixture loop B fixture canopy I from top center pipe P Feed fixture wires thro
3. chain S and attach it to the canopy loop E BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY WIRING INSTRUCTIONS A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK ee PARALLEL WIRE ROUND amp SMOOTH f PARALLEL WIRE SQUARE amp RIDGED WHITE Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture if supplied and the ground wire from
4. ugh center hole of fixture canopy I Secure BOTTOM fixture canopy l to fixture by installing nut G over center nipple WASHER amp a FIGURE1 HEX NUT Z U le FINIAL N NOT SUPPLIED GROUNDING AND MOUNTING BAR LOCK UP FOR FLUSH MOUNT OUTLET BOX sea gull lighbing Installation And Safety Instructions HC 11560 os 507 MOUNTING File This Sheet For Future Reference ITEM L MOUNTING lt BAR A SCREWS F Line art shown may not exactly match the fixture enclosed NOT INCLUDED However the installation instructions do apply to this fixture INSTALLATION HC 1156 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET OX Ww STEP 1 FLUSH MOUNT Thread fixture mounting screws F in through top of mounting bar A raised side is on top as illustrated Run screw threads all the way down to the heads Secure mounting bar A to outlet box with outlet box screws not supplied FOR CHAIN HUNG ONLY STEPS 2 4 STEP 2 Secure mounting bar A to outlet box using outlet box screws Thread nut G onto nipple C so five threads are exposed Thread nipple C into mounting bar A and secure by tightening nut G Thread screw collar H to nipple C STEP 3 Using 2 pairs of pliers open one link of chain S and connect it to the fixture loop B at the top of the fixture Slide screw collar ring L and canopy O to top of fixture STEP 4 Open one link on the other end of the
Download Pdf Manuals
Related Search