Sea Gull Lighting 65850-965 Installation Guide
Contents
1. shown may not exactly match the fixture enclosed FIGURE 1 RING L gt PY NOT SUPPLIED However the installation instructions do apply to this fixture SHADE G INSTALLATION HC 1324 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET OX Ww STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 3 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Attach collar E to nipple C STEP 2 Using 2 pairs of pliers open one link of chain J and connect it to the fixture loop K at the top of the fixture STEP 3 Slide the collar ring 1 and canopy H in that order over chain J Open one link on the other end of the chain J and attach it to the collar E which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 4 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE l HOUSE WIRE HOUSE WIRE BLACK WHITE D O PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED 4 Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires gr2. INSTALLATION AND SAFETY INSTRUCTIONS e Be sure the electricity to the system you are working on is turned off Carefully remove the fixture from the carton and check that all either the fuse removed or the circuit breaker set at off parts are included as shown in Figure 1 amp 2 Be careful not to e Use of other manufacturers components will void warranty listing and misplace any of the screws or parts which are needed to install create a potential safety hazard this fixture e If you are unclear as to how to proceed contact a qualified electrician e You don t need special tools to install this fixture e Be sure to follow the steps in the order given Attach fixture loop K to top of fixture e Read instructions carefully e To reduce the risk of fire electric shock or personal injury mount to outlet box or supporting system able to support the weight of the fixture e Save these instructions OUTLET BOX GROUNDING AND MOUNTING BAR LOCK UP g OUTLET BOX WIRE CONNECTORS MOUNTING BAR A QUTLET BOX SCREWS NUT B NIPPLE C GROUND WIRE F COLLAR E MOUNTING CANOPY H gt p BAR A R OUTLET lt gt GREEN GROUNDING SCREW D CHAIN J FIXTURE LOOP K FIGURE 2 NOT INCLUDED sea gull lighting Installation And Safety Instruction HC 1324 012808 SUPPORT Fill In Item Number On Carton And o RING M File This Sheet For Fixture Reference ITEM SE iG C lt gt Line art
3. asp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 5 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire F from the fixture and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire F from the fixture and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box and then raise the canopy H against ceiling and thread the collar ring l to the collar E STEP 2 Raise shade G over socket and secure by plac
4. ing glass support ring M onto socket and threading glass retaining ring L onto socket STEP 3 Install lamp CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search