Sea Gull Lighting 6016-12 Installation Guide
Contents
1. Na Installation And Safety Instructions il li hbj Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to 56d gu ig mg this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM IMPORTANT SAFETY INSTRUCTIONS Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off Use of other manufacturers components will void warranty listing and create a potential safety hazard If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a MOUNTING ceiling which contains a radiant type heating system A Read instructions carefully Save these instructions CONNECTORS OUTLET BOX SCREWS NIPPLE C CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders CANOPY G an 0 2 ie Q e log f 2 lt 0 me me D 5 ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illu2. aper from each side of tape place on upper end of glass install and press against casting Install lamp
3. stration when ordering parts CHAIN 1 BEFORE YOU BEGIN Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 Be careful not to misplace any of the screws or parts which are needed to install this fixture FIXTURE LOOP H Attach fixture loop H to top of fixture if applicable INSTALLATION IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 2 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 3 threads are exposed GLASS above nut B Thread nipple C into mounting bar A and secure PANELS L with nut B Attach screw collar E to nipple C CAGE J STEP 3 Using 2 pairs of pliers open one link of chain I and connect it to the fixture loop H at the top of the fixture If applicable STEP 4 Slide the screw collar ring F and canopy G in that order over chain I Open one link on the other end of the chain I and attach it to the screw collar E which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY FIGURE 1 pa HC 322 022309 OUTLET BOX GROUND WIRE NUT B GREEN GROUNDING SCREW D GROUND WIRE M SCREW COLLAR E SCREW COLLAR RING F RETAINING SCREWS K NOT INCLUDED INSTALLATION continued HC 322 STEP 5 A Use a listed wire connector to connect the fixture hot wire black
4. wire or round and smooth tracer to the supply hot wire B Use a listed wire connector to connect the fixture common wire white wire or square and rigid to the supply common wire C Gently try to remove the wires from the connector If you can remove the wires carefully re do the wiring connection GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors After wires are connected tuck them carefully inside outlet box Raise canopy G against ceiling and thread the screw collar ring G to the screw collar E Place glass panels L in cage J raise the cage J to the hood and secure with retaining screw K If applicable NOTE There is a variation in all castings in some cases the glass panels may be slightly loose when installed you may want to tape it in place Two 2 sided tape has been supplied for this purpose remove protective p
Download Pdf Manuals
Related Search