Armacost Lighting 733420 Installation Guide
Contents
1.2. Pairing and RF code technology can greatly reduce the need for extra wiring WIRELESS TOUCHPAD OPERATION RESET key will take unit to the 1 sequence warm white color At the same time it will return brightness settings on all colors to 100 Effect speeds will return to the medium speed setting Power ON OFF BRIGHTNESS Controls the light level for static colors and jump and strobe effects Brightness is not adjustable in any color fade effects COLOR MODE Press forward arrow to advance to next static color or color changing effect Press back arrow to return to previous color or effect displayed EFFECT SPEED Controls the speed of all color changing effects Arrow up for faster down for slower WIRELESS TOUCHPAD TRANSMITTER INSTALLATION Designer style wireless touchpad transmitter can easily be surface mounted or installed in wall It comes with a switch plate mounting screws and drywall anchors Also included is one 12V alkaline battery 27A The touchpad design will blend with existing residential and commercial switches and dimming d cor gt TP De Fg Can be installed in wall in some electrical boxes Easily mount to any wall or flat surface screws and anchors Designer style wall plate and screws included included _ Touchpad may not fit
3. the wireless touchpad SER gt q S 22 X ija N S POWER MAX 4A pe a oy a 4 H Sc yj a aj l gt 2 N D ae anor s R r re j ol el dio i 7 Armacost A w SIGNA Model RGB8KEY RF WR Model HHRGB 14 The wireless touchpad only works with Armacost Lighting s 30 Color RGB LED controllers models RGB8KEY RF WR and HHRGB14 Be sure the battery in the transmitter is strong In a darkened room you should see a visible red LED light glowing through the front touchpad when you press any function key If this glow is diminished or not visible replace battery with a 12V 27A alkaline battery 1 Following the instructions that came with your color controller connect the RGB color controller receiver to your power supply and RGB LED lights Be sure your power supply is turned on The red power indicator light will illuminate on model RGB8KEY Model HHRGB14 does not have a power indicator light Turn your LED lighting on and select any a static color using the mode key on the receiver Model HHRGB14 will already be on a static color or use the hand held remote that was supplied with the unit 2 Shut off power to the receiver unit by unplugging the power supply do not use the power OFF key on model RGB8KEY Wait at least 5 seconds 3 Restore power to the RGB receiver unit within 2 seconds after restoring power press and hold the power and brightness down keys simultaneously for about 2 seconds
4. This action will pair the two devices For model RGB8KEY RF WR the green signal light on the receiver will flash once to confirm successful pairing For model HHRGB14 the LED tape light will quickly flash once when paired Common Code Pairing It is possible to pair multiple receivers to the same single transmitter by simply repeating the steps above with additional receiver units Please note that only static colors will synchronize color changing effects will not synchronize due to the various cycling speeds of each unit In addition if you repeatedly press any of the touchpad keys too fast the RGB controllers will lose their synchronization To re synchronize press the reset key on the touchpad transmitter All receivers and RGB LED lighting will reset to the same warm white color For effective synchronization all receivers must be within range of the single wireless touchpad Note you can also un pair the RGB controllers by following the process above but press the brightness up and brightness down keys Common Code Pairing Unique Code Pairing o gt o gt o gt vE vE VE VE WE VE E E E
5. some smaller Tabs are of O XO electrical boxes See minimum break away 1O size dimensions removable p and choose an wn 7 for some appropriate s installations electrical box or mounting bracket Some installations L Minimum may require the sai removal of tabs hos oy bracket as shown simply Typical Low opening break away with Voltage Wall Plate 17 4 47mm X wire cutters Mounting Bracket 27 e 72mm Note Compatible with some but not all switch plates made by other Gy manufacturers O SPECIAL FEATURES COLORS AND EFFECTS Memory and Reset Function Key The unit will remember the settings for brightness and speed for each color and each effect For instance if one color is dimmed the unit will maintain that setting for that color until changed even if the power is turned off If your power goes out when it is restored the unit will go to your last color or effects setting The wireless touchpad is designed with a unique reset function key Pressing the reset key will take the RGB controller to the 1 sequence position which is a very warm white color At the same time it will automatically return the brightness settings on all colors to 100 full brightness and any programmed effect speeds will return to the medium speed setting Colors and effects Pressing the reset key will take you to the 1 static color position which is a very warm white color All colors are arranged in common color grou
6. Armacost LIGHTING ry Wireless Touchpad for 30 Color RGB LED Controller Model RGB14REM The Armacost Lighting Wireless Touchpad is for use only with Armacost Lighting s professional grade 30 Color RGB LED Controller Model RGB8KEY RF WR and 30 Color RGB Slimline Controller with Hand Held Remote HHRGB14 It provides remote control of low voltage RGB LED lighting and works through walls and doors up to 100 ft away Using radio frequency RF technology it eliminates the need to run wires from the RGB LED lighting to the wireless touchpad and is useful in projects where installing new cabling can be difficult Features RF pairing technology for expandability and multi zone lighting control The wireless touchpad can be paired to control and synchronize multiple Armacost Lighting RGB controller receivers in the same area or multiple touchpad receiver sets can control different zones of lighting in the same area without cross interference Includes designer style wireless touchpad and all necessary mounting screws and drywall anchors Also includes one 12V alkaline battery 27A Units are for dry location only If used outdoors keep in a dry location Wireless function may cease to operate properly in close to freezing temperatures SET UP AND PAIRING Your RGB color controller contains a radio frequency RF receiver that will need to be programmed or paired to recognize the frequency code of
7. eceesueueaeceeaeaeeas 433 92Mhz Transmitter DAWN y seccssccceccnccc ti ocaceeuacet ocadandisccueeaedasedexd Alkaline 27A 12V ND esters sets cetera cea eat E sectaneac ea viet neceeeae tees NWKHF 10008 Country of Origin aetna eecnete anes eaoneaesetencatec ancseeahesgene esetuee acat eaoadetcceene China Limited 1 year warranty This product is for dry location use only Improper installation improper Fe powering abuse or failure to use this device for its intended purpose will void warranty Proof of RoHS AIRAA purchase is required for all returns Questions P E e A Email support armacostlighting com This item is a Radio Frequency Device RF and as such the range of the remote control is dependent on many factors Actual operational distance will vary based on walls and line of sight obstructions and other nearby electronic devices This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment Armacost fi LIGHTING american lighting association 2012 15 Armacost Lighting All rights reserved 140 Baltic Avenue Baltimore MD 21225 141202
8. nsmitter is a radio frequency RF device and as such the range of the wireless remote control is dependent on many factors Actual operational distance will vary based on walls and line of sight obstructions and other nearby electronic devices Be sure your battery is good To check battery press the on off key in a dark room location When pressed you should see a red LED indicator light glowing from behind the surface of the touchpad If you do not see this glowing red light replace the battery Alkaline 27A 12V A battery will last from 6 months up to 2 years depending on usage The receiver may need to be paired again with your transmitter If your dimmer receiver is functioning properly and you know your transmitter battery is fresh yet the transmitter will not control your lighting please revisit the pairing instructions Static colors display uneven brightness or a color shift This may be due to voltage drop Shorten the length of your RGB lighting installation or reduce the length of RGB power wire and or use thicker wires Refer to your RibbonFlex Pro specific model s Installation Guidelines for options on other installation configurations that may reduce voltage drop For help with larger LED lighting installations email support armacostlighting com SPECIFICATIONS Working teMperature cccseccceccceeeeeeeeeeeeeeeeeaeeeness 40 to 130 F 4 to 55 C Wireless working freQUeNCy cccceccececeececeececeecec
9. pings for easy navigation colors are fully dimmable 1 5 Shades of white 31 White strobe 6 12 Shades of blue 32 Full color cross fade 13 17 Shades of green 33 Red white and green cross fade 18 21 Shades of yellow 34 Red white and blue cross fade 22 26 Shades of red 35 Red and white cross fade 27 30 Shades of purple 36 Red gold and green cross fade TROUBLESHOOTING LED tape light strip does not light flickers or there is limited or inconsistent colors Make sure the power supply and RGB color controller are turned on and receiving power Confirm you have maintained correct polarity on all wire connections V red to red green to green blue to blue when joining RGB LED strips as well as when connecting wires to the RGB color controller and to the power supply Press the reset key If any other color appears other than a warm yellow white then you have a bad connection or polarity is not correct Check to be sure all connections are secure If you have a failed connector you can easily solder wires to the LED tape and solder splice connections Soldering is the surest method for making extra reliable electrical connections Never use connectors in RV or boat applications due to possible vehicle vibrations To learn about best soldering practices visit armacostlighting com installation The wireless touchpad is not working Be sure the touchpad is in range of your receiver Try moving the touchpad closer to the receiver The tra
Download Pdf Manuals
Related Search