Casablanca 99080 Instructions / Assembly
Contents
1. 888 830 1326 Indentation Socket Installing the bulbs Install a bulb into each Installing the globe sold separately of the sockets When necessary replace with Position the indentations in the outer rim of bulbs of same type and wattage the globe so that they line up with the tabs on the inside surface of the light fixture rim Carefully lift the globe up inside the light fixture as far as it will go Rotate the globe in a clockwise direction until it is held tightly in place by the four tabs Installing the pull chain pendant Turn power on Your installation Attach the pull chain pendant to the is complete end of the short chains coming from the switch housing and the light kit MA017 01 01 14 14 L 1 888 830 1326 TYPE C ASSEMBLY INSTRUCTIONS Switch Wire Housing Connector If your fan does not have pin connectors on the wires coming from the switch housing install the wiring harness provided Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness Lower Switch Housin Lift the lower switch housing up so that the screw holes line up with the holes in the upper switch housing Install the switch housing screws and tighten securely Feed the wires through the cente2. EMBLY INSTRUCTIONS on pages 8 9 MA017 01 01 14 14 L 1 888 830 1326 TYPE A ASSEMBLY INSTRUCTIONS Housing Mounting Screw Partially install the two mounting screws If your fan does not have pin connectors into the bottom of the lower switch on the wires coming from the switch housing housing install the wiring harness provided Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness Using the single pin connectors connect Lift the light kit up to meet the the black or blue wire from the fan to the lower switch housing Wrap keyhole black wire from the light kit Connect the slots around the screws and twist white wire from the fan to the white wire counterclockwise Tighten screws from the light kit Do not allow the light kit to hang 4 only by the wire connections MA017 01 01 14 14 1 888 830 1326 Socket Installing the bulbs Install a bulb into each Installing the globe sold separately of the sockets When necessary replace with Position the indentations in the outer rim of bulbs of same type and wattage the globe so that they line up with the tabs on the inside surface of the light fixture rim Carefully lift the globe up inside the light fixture as far as it will go Rotate the globe in a clockwise direction unti
3. Low Profile Integrated Kit Installation Manual Compatible with 2xxxx Types A Z 51000 58999 fan series 59500 59999 fan series Select Casablanca Fans MA014 01 01 14 14 1 888 830 1326 BEFORE YOU BEGIN Read entire installation instructions carefully before beginning installation and save these instructions Switch Housing Your light kit is compatible with most ceiling fans The light kit will attach to the fan s switch housing Begin on page 3 where you will choose the type of switch housing that most closely resembles the one on your fan From there you will be directed to the set of assembly instructions that are appropriate for installing the light kit to your fan READ AND SAVE THESE INSTRUCTIONS This product conforms to UL Standard 507 AWARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel A CAUTIONS c 1 All wiring must be i
4. l it is held tightly in place by the four tabs Installing the pull chain pendant Turn power on Your installation Attach the pull chain pendant to the is complete end of the short chains coming from the switch housing and the light kit MA017 01 01 14 14 1 888 830 1326 TYPE B ASSEMBLY INSTRUCTIONS Housi Connector ousing s If your fan does not have pin connectors on the wires coming from the switch housing install the wiring harness provided Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness Using the single pin connectors connect the black or blue wire from the fan to the black wire from the light kit Connect the white wire from the fan to the white wire from the light kit Feed the wires through the center hole in the switch housing the washer and the nut Install the switch housing by twisting clockwise onto the threaded rod Install the washer and nut onto threaded rod and tighten securely Housing Screw Lift the light kit assembly up so that the screw holes in the lower switch housing line up with the holes in the upper switch housing Install the switch housing screws and tighten securely Do not allow the light kit to hang only by the wire connections MA017 01 01 14 14 1
5. n accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician MA017 01 01 14 14 1 888 830 1326 WHICH ASSEMBLY METHOD WILL I USE Choose one of the four images below that most closely resembles the switch housing on your fan then follow the instructions under the image Switch Housing Cap If your fan s switch housing cap resembles this one remove the cap screws with a Phillips head screwdriver Then follow the TYPE A ASSEMBLY INSTRUCTIONS on pages 4 5 Switch Housing Plug Screw Button If your fan s switch housing cap resembles this one remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver Remove the plug button Then follow the TYPE B ASSEMBLY INSTRUCTIONS on pages 6 7 Housing Cap If your fan s switch housing cap resembles this one remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver Remove the two cap screws from the inside of the switch housing Reinstall the switch housing Tighten the switch housing screws Then follow the TYPE A ASSEMBLY INSTRUCTIONS on pages 4 5 Housing If your fan s switch housing cap resembles this one remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver Remove the plug button using a standard screwdriver Then follow the TYPE C ASS
6. r hole in the switch housing Then using the single pin connectors connect the black or blue wire from the fan to the black wire from the light kit Connect the white wire from the fan to the white wire from the light kit Lift the light kit up tucking the wires into the hole in the switch housing Install the center stem of the light kit into the lower switch housing by turning the threaded rod clockwise into the threaded hole Continue turning until tight Do not allow the light kit to hang only by the wire connections MA017 01 01 14 14 TYPE C ASSEMBLY INSTRUCTIONS CONTINUED Indentation Socket Installing the bulbs Install a bulb into each Installing the globe sold separately of the sockets When necessary replace with Position the indentations in the outer rim of bulbs of same type and wattage the globe so that they line up with the tabs on the inside surface of the light fixture rim Carefully lift the globe up inside the light fixture as far as it will go Rotate the globe in a clockwise direction until it is held tightly in place by the four tabs Installing the pull chain pendant Turn power on Your installation Attach the pull chain pendant to the is complete end of the short chains coming from the switch housing and the light kit MA017 01 01 14 14 q 1 888 830 1326 TROUBLESHOOTING Lights don t come on Make
7. sure that the bulbs are properly installed Make sure power switch is on Pull the pull chain to make sure it is on Check the circuit breaker to ensure the power is turned on Check the pin connections in the light kit Refer to the fan manual for locating the fan s wiring Verify that the light and power wires are correctly connected to the ceiling and the light kit ONE YEAR WARRANTY This product is warranted to the original purchaser by Casablanca Fan Company Hunter Fan Company against defects in material and workmanship for one 1 year from date of purchase During the warranty period we will repair or at our option replace a defective product at no charge For information on how to obtain service contact the Casablanca Hunter Service Department by calling our toll free number at 888 830 1326 Damage to the product caused by mishandling improper installation or modification is not covered by this warranty This warranty is given in lieu of all other warranties expressed or implied Some states do not allow limitations of time on an implied warranty therefore the above limitations may not apply in every case This warranty states specific legal rights which may vary from state to state If you have problems installing or operating your light kit do not return this product to the dealer Call our Consumer Affairs Hotline 888 830 1326 10 MA017 01 01 14 14
Download Pdf Manuals
Related Search