none 13431103002300 Use and Care Manual
Contents
1. Operation continued INSTALLING THE REMOTE CONTROL HOLDER Attach the remote control holder 0 with the two remote control holder mounting screws EE Care and Cleaning Do Check the support connections brackets and blade attachments twice a year Ensure they are secure Because of the fan s natural movement some connections may become loose over time It is not necessary to remove the fan from the ceiling Clean your fan periodically Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or tarnishing Optional Apply a light coat of furniture polish to the wood blades Optional Cover small scratches with a light application of shoe polish Do not Do not use water when cleaning Water could damage the motor or the wood or possibly cause an electrical shock Do not apply oil to your fan or motor The motor has permanently lubricated sealed ball bearings 16 Troubleshooting panel box before you attempt any repairs Refer to the section WARNING Ensure the power is off at the electrical Making the Electrical Connections on page 11 Problem Solution The fan will not start Check main and branch circuit fuses or breakers Check line wire connections to the fan and switch wire2. Please contact 1 877 527 0313 for further assistance Pre Installation continued HARDWARE INCLUDED NOTE Hardware shown to actual size unless noted otherwise in the table below Prom EE Cmm i A KK Part Description Quantity AA Blade screw 16 BB Fiber washer not to scale 16 CC Blade holder screw 11 DD Balance kit not to scale 1 EE Remote control holder mounting screws 2 FF Wire nuts 6 GG Cross pin not to scale preassembled 1 HH Hitch pin preassembled 1 ll Lock pin not to scale preassembled 1 JJ Hanger ball set screw preassembled 1 KK Fan motor assembly coupling set screw preassembled 2 LL Mounting bracket screw preassembled 2 MM Fan motor assembly mounting ring screw preassembled 3 NN Light kit plate screw preassembled 3 Pre Installation continued PACKAGE CONTENTS a Part Description Quantity Blade 5 Part Description Quantity Mounting bracket Canopy Blade holder 5 Canopy cover Light kit plate 17W LED asembly Hanger ball preassembled Glass shade Downrod preassembled Receiver Couping cover Remote control Ziolnmmo o w gt Fan motor assembly ee b b b b ee d Remote con
3. connections in the switch housing Check to make sure the dip switches from the remote control and receiver are set to the same frequency Make sure all motor housing screws are snug Make sure the screws that attach the fan blade arm to the motor hub are tight The fan sounds noisy Make sure wire nut connections are not rattling against each other or the interior wall of the switch housing Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this time If using the ceiling light kit make sure the screws securing the glassware are tight Check that the light bulb is also secure Make sure there is a short distance from the ceiling to the canopy It should not touch the ceiling Make sure your ceiling box is secure and rubber isolator pads are used between the mounting bracket and outlet box The remote control is not working Do not connect the fan with wall mounted variable speed control s Check to make sure the dip switches from the remote control and receiver are set to the same frequency The fan wobbles Check that all blade and blade arm screws are secure Most fan wobble problems are caused when blade levels are unequal Check this level by selecting a point on the ceiling above the tip of one of the blades Measure from a point on the center of each blade to
4. mounting bracket B and loosen the other screw LL approximately 1 4 turn Carefully raise the canopy C up to the mounting bracket B and ensure the loosened screw LL is inserted into the key hole on the canopy C Rotate the canopy C clockwise Secure the canopy C by replacing the screw LL previously removed and tightening the screw LL previously loosened Place the canopy cover D on the canopy C and rotate the canopy cover D clockwise until it locks into position A il C u y L Gj 11 HOMEDEPOT COM HOMEDECORATORS Please contact 1 877 527 0313 for further assistance Assembly Attaching the Fan Blade Assemblies 8 Fastening the blade assemblies to the fan motor assembly Attach the fan blades A to the blade holders I by using three blade screws AA and fiber washers BB Tighten screws AA and fiber washers BB securely Insert the blade holder I through the slots on the fan motor assembly H Attach the blade holder I to the fan motor assembly H using the blade holder screws CC and tighten them securely Repeat this step for the other blade holders l Assembly Installing the Light Kit 9 Attaching the light kit plate 1 0 Attaching the 17W LED Assembly to the mounting rin
5. HOME Item 000 000 DECORATORS Model SW1478 ORB COLLECT LON USE AND CARE GUIDE DURANGO 52 INCH CEILING FAN Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 HOMEDEPOT COM HOMEDECORATORS THANK YOU We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this ceiling fan We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Home Decorators Collection Table of Contents Table Of Contents ccccccceseesesesesssesseeeseseeessssssssseneeseenenes 2 Safety Information 2 cccceeeeeeessesseeeeeeeeeeeeeeeeeensenseees 2 WAIT AIMY sees ccc feed spe ces states aana addaa iad cu sueredueeasc lt cucassanees 3 Pre installation siiiccccsissscscscscscscccsscccicccsessssnasscdstsaececcussees 3 SDOCITICATIONS isidin riranin 3 Tools Required s sessssssssssssssnsnsnsusunensnsnsnsnsnnnonsnnanannnennnnennnnna 3 Hardware included nsinanstininananana 4 Package Contents ssssssesssssssnsrssnsrssnnssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnns 5 IS tallati OM eis scscccsctieccicccccsdicasndscsiadsanstustectecscssictesctescacsacs 6 Assembly ses css swine ce sti ccitn cnc ea een ee stint ne ecnscneieecn emt 7 Hanging the Fan cess scescccesct
6. a m 6 p m EST Monday Friday 1 877 527 0313 HOMEDEPOT COM HOMEDECORATORS Retain this manual for future use
7. asstesezesdsctvesctacetesatatsdenesctsassesasetanecess 7 Attaching the Fan Blades ccccssssssesssseessseeseseseeeeeees 12 InStalling the Light Kitosi 13 OP Oration 25 ac cc csc ccseasses scecenscncdececenstenccsaecnencscseeceseectaaeend 15 Remote Control Operating INStruCtiOnS cccscseseseseseeeees 15 Reverse Function Button Operating Instructions 15 Installing the Remote Control Holder sccssssseseeeeees 16 Care and Cleaning sivsiiicccsissniceictstetcenntcenaaccnavsnasacetaaanee 16 Troubleshooting iciccesisnnnnseiennnes onveevuccesannuecnaatenineenanecu 17 Service PaitSivseisccecceseccsccsenescadecctsaascsnseszeezcetsceeccasectunce 18 Safety Information Read and save these instructions To reduce the risk of electric shock ensure electricity has been turned off at the circuit breaker or fuse box before beginning All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 1999 and local electrical codes Electrical installation should be performed by a qualified licensed electrician The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 Ibs Use only UL Listed outlet boxes marked FOR FAN SUPPORT The fan must be mounted with a minimum of 7 ft clearance from the trailing edge of the blades to the floor To avoid personal injury or damage to the fa
8. be free from defects in workmanship and material present at time of shipment from the factory for a period of 15 years after the date of purchase by the original purchaser We also warrant that all other fan parts excluding any glass or acrylic blades to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned To obtain warranty service you must present a copy of the receipt as proof of purchase All costs of removing and reinstalling the product are your responsibility Damage to any part such as by accident misuse improper installa tion or by affixing any accessories is not covered by this warranty Because of varying climatic conditions this warranty does not cover any changes in brass finish including rusting pitting corroding tarnishing or peeling Brass finishes of this type give their longest useful life when protected from varying weather conditions A certain amount of wobble is normal and should not be considered a defect Servicing performed by unauthorized persons shall render the warranty invalid There is no other express warranty We hereby disclaim any and all warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by
9. cal wiring knowledge or experience have your fan installed by a licensed electrician This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units The frequency switches on your receiver M and remote control N have been preset at the factory Please recheck to make sure the switches on the remote control N and the receiver M are set to the same position Any combination of settings will operate the fan as long as the remote control N and receiver M are set to the same position Insert the receiver M into the mounting bracket B with the flat side of the receiver M facing the ceiling 9 HOMEDEPOT COM HOMEDECORATORS Please contact 1 877 527 0313 for further assistance Assembly Hanging the Fan continued F Making the electrical connections electricity is turned off at the circuit breaker or main fuse box i WARNING To avoid possible electrical shock ensure the C before wiring i WARNING Check to see that all connections are tight including the ground and that no bare wire is visible at the Black White wire nuts except for the ground wire Black White Follow the steps below to connect the fan to your house supply wires Secure the wire nuts FF supplied with your fan by wrapping the connections with electrical tape Green Green M Motor to receiver electri
10. cal connections is l I Connect the black wire from the fan to the black wire marked TO MOTOR L from the receiver M Connect the white wire from the fan to the white wire marked TO MOTOR N from the receiver M Black Blue White Black Blue White Connect the blue wire from the fan to the blue wire marked For Light from the receiver M Receiver to house supply wires electrical connections Connect the black hot wire from the ceiling to the black wire marked AC in L from the receiver M A x6 Connect the white neutral wire from the ceiling to E the white wire marked AC in N from the receiver M If your outlet box 1 has a ground wire green or bare copper connect it to the fan ground wires otherwise connect the hanging ball E ground wire to the mounting bracket B H Secure the wire connection with a plastic wire nut a J FF provided with the electrical hardware After connecting the wires spread them apart so that the green and white wires are on one side of the outlet box 1 and the black and blue wires are on the other side Carefully tuck the wire connections up into the outlet box 1 10 Assembly Hanging the Fan continued 7 Securing the fan motor assembly to the mounting bracket Remove one screw LL from the
11. ery P into the remote control N To prevent damage to the remote control remove the battery if not used for long periods of time connect improperly or dispose of used batteries in fire Do not recharge or mix batteries with used or other battery types Immediately remove used batteries i WARNING Do not short circuit disassemble heat up Restore power to the ceiling fan and test for proper operation HI MED LOW buttons Sets the fan speed button Turns the fan off Q button Turns the light ON or OFF Press and hold the button to set the desired brightness REVERSE FUNCTION BUTTON OPERATING INSTRUCTIONS The reverse switch is located on the surface of the fan motor assembly This switch controls directions forward switch left or reverse switch right NOTE Wait for the fan to stop before reversing the direction of the blade rotation Warm weather Counterclockwise Direction A downward air flow creates a cooling effect This allows you to set your air conditioner on a higher setting without affecting your comfort Cool weather Clockwise Direction An upward air flow moves warm air off the ceiling This allows you to set your heating unit on a lower setting without affecting your comfort s a cn LE y z Ly 15 HOMEDEPOT COM HOMEDECORATORS Please contact 1 877 527 0313 for further assistance
12. g to the light kit plate Remove one of three screws MM from the fan motor Remove one of three screws NN from the light kit assembly H mounting ring and loosen the other two plate J and loosen the other two screws NN but do screws MM but do not remove not remove Place the key holes from the light kit plate J over the While holding the 17W LED assembly K under your fan two screws MM previously loosened from the fan firmly snap the wire connection plugs PP together motor assembly H mounting ring Turn the light kit plate J until it locks in place at the narrow section of Place the key holes from the 17W LED assembly K over MM previously loosened and the one screw MM plate J Turn the17W LED assembly K until it locks in previously removed place at the narrow section of the key holes Secure by tightening the two screws NN previously loosened and the one screw NN previously removed wm NN 13 HOMEDEPOT COM HOMEDECORATORS Please contact 1 877 527 0313 for further assistance Assembly Installing the Light Kit continued 1 2 Installing the glass shade Attach the glass shade L to the light kit plate J by twisting tightly Operation REMOTE CONTROL OPERATING INSTRUCTIONS Install a 12V batt
13. law The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you The retailer shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law Some states do not allow the exclusion of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all prior warranties Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer Contact the Customer Service Team at 1 877 527 0313 or visit www HOMEDEPOT COM HOMEDECORATORS Pre Installation SPECIFICATIONS Fan size Speed Volts Amps Watts RPM CFM N W G W C F Low 0 25 15 3 68 1959 8 87 k 40 10 k 52 in Medium 120 0 38 32 8 108 3365 ao a i 1 85 ft High 0 50 59 4 160 5230 l l NOTE These are approximate measures They do not q include amps and wattage used by the light kit Intertek TOOLS REQUIRED Phillips Flat blade Step Wire Electrical i screwdriver K screwdriver ladder stripper Tape 3 HOMEDEPOT COM HOMEDECORATORS
14. n and other items be cautious when working around or cleaning the fan Do not use water or detergents when cleaning the fan or fan blades A dry dust cloth or lightly dampened cloth will be suitable for most cleaning After making electrical connections spliced conductors should be turned upward and pushed carefully up into the outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box All setscrews must be checked and retightened where necessary before installation WARNING To reduce the risk of electrical shock or fire do AN not use this fan with any solid state fan speed control device It will permanently damage the electronic circuitry WARNING To reduce the risk of personal injury do not bend the blade arms also referred to as flanges when installing the brackets balancing the blades or cleaning the fan WARNING Do not insert foreign objects between rotating fan blades WARNING To reduce the risk of fire electric shock or personal injury mount the fan to the outlet box marked acceptable for fan support with the screws provided with the outlet box CAUTION To reduce the risk of personal injury use only the screws provided with the outlet box Warranty We warrant the fan motor to
15. nd the hitch pin HH Tighten the set screws KK ce a l JJ a gt O F HH O t amp E 0 HOMEDEPOT COM HOMEDECORATORS Please contact 1 877 527 0 513 forfurtherasp istance Assembly Hanging the Fan continued 3 Attaching the coupling cover canopy cover and canopy to the downrod Slip the coupling cover G canopy cover D and canopy C onto the downrod F Carefully reinstall the hanger ball E onto the downrod F and ensure that the cross pin GG is in the correct position the set screws JJ are tight and the wires are not twisted eG dib A E Q A Is 4 Hanging the fan motor assembly from the mounting bracket Lift the fan motor assembly H into position and place the hanger ball E into the mounting bracket B Rotate the fan motor assembly H until the check groove drops into the registration slot 00 and seats firmly The downrod F should not rotate if this is done correctly Assembly Hanging the Fan continued 5 Preparing the receiver and remote control WARNING To avoid possible electrical shock ensure the electricity is turned off at the main fuse box before wiring CAUTION Do not use with a wall light dimmer switch A NOTE If you feel you do not have enough electri
16. ng on a steep sloped ceiling The maximum angle allowable is 18 If the canopy touches a 2 the downrod remove the decorative canopy bottom cover and turn the canopy 180 before attaching the canopy to the mounting plate 2 Assembly Hanging the Fan Attaching the mounting bracket to the electrical box A WARNING To reduce the risk of fire electric shock or other personal injury mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box Place the slots from mounting bracket B over the two screws provided with the outlet box Slide the mounting bracket B until it locks in place at the narrow section of the slots Securely tighten the two mounting screws i Ow ON 2 Attaching the downrod to the fan motor assembly Loosen the two set screws KK from the fan motor assembly H coupling Remove the hitch pin HH and lock pin Il from the downrod F Remove the hanger ball E from the downrod F by loosening the hanger ball set screw JJ and removing the cross pin GG then sliding the hanger ball E off of the downrod F Carefully feed the fan wires up through the downrod F Thread the downrod F into the fan motor assembly H coupling Line up the holes and replace the lock pin Il a
17. the point on the ceiling Rotate the fan until the next blade is positioned for measurement Repeat for each blade Measurements deviation should be within 1 8 in Run the fan for 10 minutes Use the enclosed blade balancing kit if the blade wobble is still noticeable 187 HOMEDEPOT COM HOMEDECORATORS Please contact 1 877 527 0313 for further assistance Service Parts y EJ reat Description Blade Mounting bracket Canopy Canopy cover Hanger ball Downrod Coupling cover Fan motor assembly Blade holder Light kit plate 17W LED assembly Glass shade Receiver Remote control Remote control holder VO z z m AXA e TI olnm ojojo 12V battery CC mmm EE FF GG uw HH KK LL MM NN Part Description AA Blade screw BB Fiber washer CC Blade holder screw DD Balance kit EE Remote control holder mounting screws FF Wire nuts GG Cross pin HH Hitch pin Il Lock pin JJ Hanger ball set screw KK Fan motor assembly coupling set screw LL Mounting bracket screw MM Fan motor assembly mounting ring screw NN Light kit plate screw 18 HOME DECORATORS COLLECTION Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8
18. trol holder vl o 2 r xA Cc 12V Battery ee b b b ee d d HOMEDEPOT COM HOMEDECORATORS Please contact 1 877 527 0313 for further assistance Installation MOUNTING OPTIONS A WARNING To reduce the risk of fire electric shock or personal injury mount the fan to an outlet box marked acceptable for fan support using the screws provided with the outlet box An outlet box commonly used for the support of lighting fixtures may not be acceptable for fan support and may need to be replaced If in doubt consult a qualified electrician If your ceiling fan does not have an existing UL listed mounting then install one using the following instructions box Disconnect the power by removing the fuses or turning off the circuit breakers Secure the outlet box 1 not included directly to the building structure Use appropriate fasteners and materials not included The outlet box and its bracing must be able to fully support the weight of the moving fan at least 35 Ibs Do not use a plastic outlet box The illustrations to the right show three different ways to mount the outlet box not included To hang your fan where there is an existing fixture but no Ceiling joist you may need an installation hanger bar 3 not included as shown a NOTE You may need a longer downrod to maintain proper blade clearance when installi
Download Pdf Manuals
Related Search