AireRyder LK51211OR Use and Care Manual
Contents
1. ie Hex Nut am ii m Stem a NL Leon medium base spiral fluorescent Bulb Max 13W incluced Short Nipple Pull Chain Glass Shade Assembly 10 Follow steps 9 12 as For Light Kit LK51211 Page 2 SHC ZA Rubber Pad Metal Pad ome aireRyder F A N 0904062. 3 Attach the mounting strap to the outlet box by using two mounting screws 4 Thread the fixture wires through the coupling hex nut long nipple big tube cap canopy metal pad washer grounding pad and another hex nut 5 Secure the coupling onto the stem on the top of the light kit Then screw the long nipple into the coupling then secure it with a hex nut 6 Slip the big tube cap with the open side facing downward and the canopy down through the long nipple secure them together with a metal pad washer grounding pad and hex nut 7 Follow step 1 as For Light Kit 8 Cut the redundant wires if necessary Pull out the outlet wires and the house grounding wire from the outlet box Make wire connections using the wire nuts Connect the black wire from fixture to the black wire from power source Connect the white wire from fixture to the white wire from power source Attach the fixture grounding wire to the mounting strap with the green grounding screw Then connect it to the house grounding wire with the wire nut Carefully put wires back into the outlet box 9 Attach the canopy to the mounting strap and secure it with the bolt nuts Outlet Box House Grounding Wire Lo Wire Nut po Ceres a L lt Mounting Strap a Lock Nut f A Screw Green Grounding Screw HexNut S Grounding Pad Washer Metal Pad O gt 0 aneo Da Bolt Nut Cap Big Tube Long Nipple
3. ASSEMBLY AND INSTALLATION Po INSTRUC TIONS WARNING BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE NOTE 1 Before installing consult local electrical codes for wiring and grounding requirements 2 The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless additional support is provided for the fan Fig 2 ae T Motor Fig 1 Motor Screw 0 iu Switch Box Cover Black or Blue Wire White Wire Wire Nut Terminal Groove Black or Blue Wire Switch Box Wire Nut White Wire Black Wire hae Washer al Screw Switch Box Cover Nipple Black Wire Terminal Tongue White Wire Switch Box Center Plug Set Screw 6 x 32 20mmL E C o y O Light lt D Sn lt 7 E26 medium base spiral fluorescent Bulb Max 13W incluced Light Kit Glass Shade gt Screw a Moor Metal Frame Short Nipple Pull Chain po e Shade Assembly For Light Kit 1 Place the glass shade into the metal frame DOLIO as shown in Fig 4 secure it with clips and set screws 2 Remove the switch box cover from the switch box of the fan by loosing the three switch box Rubber Pad screws Metal Pad e Hex Nut 3 Unscrew the center plug from the switch box Cover cover and discard it Fig 1 Finial 4 Thread the fixture wire through the switch box
4. cover Fig 1 5 For fan style that is shown in Fig 1 Attach the nipple of the light kit to the hole of the switch box cover then thread the wires through the washer and hex nut then secure them tightly 6 For fan style that is shown in Fig 2 Thread the fixture wire through the switch box then attach the light kit to the switch box and secure it with two set screws 6x32 20mmL 7 Pull out the wires from the switch box Make wire connections using the wire nuts The black wire from light kit to the black or blue wire from the fan The white wire from light kit to the white wire from the fan Carefully put wires back into the switch box 8 Attach the switch box cover back to the switch box using the three switch box screws 9 Install bulbs included See relamping label at socket area or packaging for maximum allowed wattage 10 Slip the glass shade assembly up through the pull chain and the short nipple secure them with a rubber pad metal pad and hex nut 11 Slip the cover up through the pull chain and the short nipple secure it with finial 12 Turn on the power at the main fuse or circuit breaker box You can control the light with the pull chain aireRyd er F_A_N LK51211 Page 1 090406 For Semi Flush 1 Take out the parts from the hardware package For Semi Flush 2 Attach two screws to the mounting strap and secure it with two lock nuts Adjust the length of the screws if necessary
Download Pdf Manuals
Related Search