Casablanca 99065 Instructions / Assembly
Contents
1. c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician MA005 01 07 24 13 1 888 830 1326 WHICH ASSEMBLY METHOD WILL I USE Choose one of the four images below that most closely resembles the switch housing on your fan then follow the instructions under the image Switch Housing Cap If your fan s switch housing cap resembles this one remove the cap screws with a Phillips head screwdriver Then follow the TYPE A ASSEMBLY INSTRUCTIONS on pages 4 5 CEE LP 2 Housing Screw If your fan s switch housing cap resembles this one remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver Remove the plug button Then follow the TYPE B ASSEMBLY INSTRUCTIONS on pages 6 7 Switch Housing Cap gt Housing Screw If your fan s switch housing cap resembles this one remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver Remove the two cap screws from the inside of the switch housing Reinstall the switch housing Tighten the switch housing screws Then follow the TYPE A ASSEMBLY INSTRUCTIONS on pages 4 5 Switch Housing Screw If your fan s switch housing cap resembles this one remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver Remove the plug bu2. screws and tighten securely Do not allow the light kit to hang only by the wire connections MA005 01 07 24 13 TYPE B ASSEMBLY INSTRUCTIONS CONTINUED Indentation Installing the bulb connect the four pin connector to the four pins on the bulb Raise the bulb up and secure it to the light kit using the bulb clamps Installing the globe sold separately Position the indentations in the outer rim of the globe so that they line up with the tabs on the inside surface of the light fixture rim Carefully lift the globe up inside the light fixture as far as it will go Rotate the globe in a clockwise direction until it is held tightly in place by the four tabs Installing the pull chain pendant Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit Turn power on Your installation is complete MA005 01 07 24 13 L 1 888 830 1326 TYPE C ASSEMBLY INSTRUCTIONS Switch Housin 9 Connector If your fan does not have pin connectors on the wires coming from the switch housing install the wiring harness provided Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness Housing Lift the lower switc
3. accessories not authorized by us mishandling improper installation modifications or damage to the light fixture while in your possession or unreasonable use including failure to provide reasonable and necessary maintenance IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE If you have problems installing or operating your light kit do not return this product to the dealer Call our Consumer Affairs Hotline 888 830 1326 Monday through Friday 8 00 am to 4 30 pm Central 10 MA005 01 07 24 13
4. Energy Star Low Profile Integrated Kit Installation Manual Models 99065 99066 99067 99068 99069 Compatible with 2xxxx Types A Z 51000 58999 fan series 59500 59999 fan series Select Casablanca Fans MA005 01 07 24 13 1 888 830 1326 BEFORE YOU BEGIN Read entire installation instructions carefully before beginning installation and save these instructions Switch Housing Your light kit is compatible with most ceiling fans The light kit will attach to the fan s switch housing Begin on page 3 where you will choose the type of switch housing that most closely resembles the one on your fan From there you will be directed to the set of assembly instructions that are appropriate for installing the light kit to your fan READ AND SAVE THESE INSTRUCTIONS This product conforms to UL Standard 507 AWARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel A CAUTIONS
5. arefully lift the globe up inside the light fixture as far as it will go Rotate the globe in a clockwise direction until it is held tightly in place by the four tabs Installing the pull chain pendant Turn power on Your Attach the pull chain pendant to the installation is complete end of the short chains coming from the switch housing and the light kit MA005 01 07 24 13 1 888 830 1326 TYPE B ASSEMBLY INSTRUCTIONS Feed the wires through the center hole in the switch housing the washer and the nut Then install the switch housing by twisting clockwise onto the threaded rod Install the washer and nut onto threaded rod and tighten securely Using the single pin connectors connect the black or blue wire from the fan to the black wire from the light kit Connect the white wire from the fan to the white wire from the light kit Switch Housin S g Connector N If your fan does not have pin connectors on the wires coming from the switch housing install the wiring harness provided Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness Housing Screw Lift the light kit assembly up so that the screw holes in the lower switch housing line up with the holes in the upper switch housing Install the switch housing
6. h housing up so that the screw holes line up with the holes in the upper switch housing Install the switch housing screws and tighten securely _ p azeeeseemeocooeoeceneooo A Feed the wires through the center hole in the switch housing Then using the single pin connectors connect the black or blue wire from the fan to the black wire from the light kit Connect the white wire from the fan to the white wire from the light kit Upper E Switch b f Housing Lift the light kit up tucking the wires into the hole in the switch housing Install the center stem of the light kit into the lower switch housing by turning the threaded rod clockwise into the threaded hole Continue turning until tight Do not allow the light kit to hang only by the wire connections MA005 01 07 24 13 TYPE C ASSEMBLY INSTRUCTIONS CONTINUED Indentation Installing the bulb connect the four pin connector to the four pins on the bulb Raise the bulb up and secure it to the light kit using the bulb clamps Installing the globe sold separately Position the indentations in the outer rim of the globe so that they line up with the tabs on the inside surface of the light fixture rim Carefully lift the globe up inside the light fixture as far as it will go Rotate the globe in a clockwise direction until it is held tightly in place by the four tabs Installing the
7. pull chain pendant Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit Turn power on Your installation is complete MA005 01 07 24 13 q 1 888 830 1326 TROUBLESHOOTING Lights don t come on Make sure that the bulbs are properly installed Make sure power switch is on Pull the pull chain to make sure it is on Check the circuit breaker to ensure the power is turned on Check the pin connections in the light kit Refer to the fan manual for locating the fan s wiring Verify that the light and power wires are correctly connected to the ceiling and the light kit 2 YEAR ENERGY STAR LIGHT KIT WARRANTY The Hunter Fan Company Casablanca Fan Company makes the following warranty to the original user or consumer purchaser of each Hunter Casablanca Energy Efficient Light Kit If your Hunter Casablanca Energy Efficient Light Kit fails at any time within two years after the date of sale due to a defect in material or workmanship labor to repair the defect will be provided free of charge at our nearest service center or our service department in Memphis TN You will be responsible for all labor costs after this two year period This warranty is voided if this product is not purchased in the U S A or Canada This warranty excludes and does not cover defects malfunctions or failures of any product which were caused by repairs by persons not authorized by us use of parts or
8. tton using a standard screwdriver Then follow the TYPE C ASSEMBLY INSTRUCTIONS on pages 8 9 MA005 01 07 24 13 L 1 888 830 1326 TYPE A ASSEMBLY INSTRUCTIONS Mounting Screw Partially install the two mounting screws into the bottom of the lower switch housing Using the single pin connectors connect the black or blue wire from the fan to the black wire from the light kit Connect the white wire from the fan to the white wire from the light kit Switch Housing If your fan does not have pin connectors on the wires coming from the switch housing install the wiring harness provided Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness Lift the light kit up to meet the lower switch housing Wrap keyhole slots around the screws and twist counterclockwise Tighten screws Do not allow the light kit to hang only by the wire connections MA005 01 07 24 13 TYPE A ASSEMBLY INSTRUCTIONS CONTINUED Indentation Installing the bulb connect the four Installing the globe sold separately pin connector to the four pins on the Position the indentations in the outer rim of bulb Raise the bulb up and secure it to the globe so that they line up with the tabs the light kit using the bulb clamps on the inside surface of the light fixture rim C
Download Pdf Manuals
Related Search