Aspects SWC313SCT Installation Guide
Contents
1. 1 of 1 8060614 R1 Fluorescent design efficiency technology American Oy u2. Open one chain link and attach chain to loop 8 close chain link and thread loop onto tube Weave fixture cord through chain as desired Insert wire through canopy ring 5 Insert loop nut 5 thru ring amp canopy 4 and secure it to canopy with nut 3 Pull the wires tight and cut cord allowing for 6 inches of wire for junction box wiring Carefully remove outer insulation from cord without damaging lead wires Strip lead wires back 3 8 inch for wire nut connections WARNING Inspect modified cord and wires for any damaged insulation G Attach three SWC models or four SWP models decorative bars to tube by securing them with ball nuts H Thread decorative base 13 onto tube and attach securely 3 Fixture mounting A Install mounting bracket 1 to outlet box not supplied with 8 32 x 1 screws B Pass wires through nipple 2 in mounting bracket 4 Wiring All wiring must take place inside junction box Caution Make sure power is off at fuse or circuit breaker box Check power wires for damage or scrapes If power supply wires are within three inches of ballast use wire suitable for at least 90C 194F Note Most dwellings built before 1985 have supply wire rated to 60C Consult a qualified electrician before installing A This unit will not operate properly unless connected to a grounded electrical circuit Electrical shock overheating low or no light output and shortened lamp life can result if proper groundin
3. SWP amp SWC Fixtures Fluorescent Pendant Fixture Models SWC313 amp SWP313 Safety Precautions Read all safety precautions and installation instructions carefully This fixture is designed for use in a 110 120VAC 60Hz fused circuit before installing or servicing this fixture Failure to comply with Do not use on a dimming circuit these instructions could result in potentially fatal electric shock and or property damage To reduce the risk of electrical shock and to assure proper operation l B l this fixture must be adequately grounded To accomplish proper It is recommended that a qualified electrician perform all wiring This grounding there must be a separate ground wire green or bare metal electrical codes connection of your main power supply panel The green ground l l l screw location is clearly marked on the fixture housing Do not handle any energized fixture or attempt to energize any fixture with wet hands or while standing on a wet or damp surface or This fixture is intended to be used for general indoor lighting in dry in water or damp locations only Assembly Instructions SWC313 model shown 1 Preparing for installation A Disconnect electrical power before installing or servicing this fixture B Carefully remove all components from packaging 2 Fixture Assembly A Determine desired chain length open link of chain 7 at desired length insert canopy loop 6 to chain then close chain link B
4. g is not done Securely attach bare ground wire to supply ground and attach to green ground screw on mounting bracket x B Using wire connectors connect white ribbed or flat sided fixture wire to the white supply wire Connect black smooth or round fixture wire to the black hot supply wire Do not mix wires Pull on each wire lead to make sure connections are secure Make certain no bare wires are exposed outside of wire connectors C Install canopy 4 flush to ceiling and thread loop nut 6 onto nipple 2 5 Diffuser Mounting A Install glass 11 into cup over threaded socket 12 and secure with threaded socket collar attachment 10 6 Lamping A Install 13 watt self ballasted compact fluorescent spiral lamp 9 provided into socket by inserting pins into holder and twist until it locks in place CAUTION RISK OF FIRE Max 13 watt type GU 24 TCP 33113SP or Maxlite MLSI3Z3GUWW recommended for replacement only 7 Power to fixture can now be restored eiukole Limited Factory Warranty American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 2 years from date of purchase This warranty covers all component parts and extends only to replacement of defective fixture or components it does not cover failure due to improper installation misuse mishandling or damage incurred in transit Page
Download Pdf Manuals
Related Search