Sea Gull Lighting 51521-845 Installation Guide
Contents
1. E BAR A CHAIN S A A OUTLET BOX FIXTURE LOOP K PERNS lt NUT B GROUNDING E RN NIPPLE C FIGURE 2 NOT SUPPLIED _ sea gull lighting Installation And BOBECHE 0 Safety I nstruction HC 1 151 081307 Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM FIGURE 1 EE NOT SUPPLIED INSTALLATION HC 1151 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that five threads are exposed above nut B Thread nipple C into mounting bar A and secure by tightening nut B to mounting bar A Thread screw collar E to nipple C 2 Using two pairs of pliers open one link of chain S and connect it to the fixture loop K at the top of the fixture Pass the wire through screw collar ring G and canopy H Slide screw collar ring G and canopy H to fixture loop K 3 Open one link on the other end of the chain S and attach it to screw collar E BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY 4 Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the following directions GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE WHITE BLACK Gmm PARALLEL WIRE ROUND amp SMOOTH N CL E e oo PARALLEL WIRE SQUARE amp RID2. GED Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner 5 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire F from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A If uninsulated wire is on the mounting bar A connect the ground wire F from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors 1 After wires are co
3. INSTALLATION AND SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS BEFORE YOU BEGIN Be sure the electricity to the system you are working on is turned Carefully remove the fixture from the carton and check that all parts off either the fuse removed or the circuit breaker set at off are included as shown in Figures 1 amp 2 Be careful not to misplace Use of other manufacturers components will void warranty listing any of the screws or parts which are needed to install this fixture and create a potential safety hazard To reduce the risk of fire electric shock or personal injury mount to STEP 1 outlet box or supporting system able to support the weight of the fixture Rotate arms N if applicable If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully Save these instructions D e OUTLET BOX GROUNDING AND MOUNTING GROUND WIRE BAR LOCK UP WIRE CONNECTORS y ae BOX lt gt j MOUNTING BAR A GROUND WIRE gs OUTLET BOX SCREWS P ARE Tins SCREW COLLAR E a CANOPY H NUT B NIPPLE C TiO de K SCREW COLLAR L MOUNTING RING G
4. nnected tuck them carefully inside outlet box and then raise the canopy H against the ceiling and thread the screw collar ring G to the screw collar E 2 Place glass M into bobeche O 3 Install lamps CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search