Sea Gull Lighting 65661-839 Installation Guide
Contents
1. Na Installation And Safety Instructions HC 1435 il li hbj Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to sta gu ig mg this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM 112508 IMPORTANT SAFETY INSTRUCTIONS e Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off Use of other manufacturers components will void warranty listing and create a potential safety hazard To reduce the risk of fire electric shock or personal injury mount to outlet box or supporting system able to support the weight of the fixture If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a GROUND WIRE ceiling which contains a radiant type heating system MOUNTING BAR A e Read instructions carefully NUT B e Save these instructions a lt Cech NIPPLE C J CLEANING eeann S kano To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders A SCREW COLLAR E steel wool or abrasive paper SCREW COLLAR RING F ORDERING PARTS Keep this2. oles of top diffuser mounting area Place top diffusers I onto washers and secure by threading top diffuser retaining screws J through top diffusers I washers and threaded holes of top diffuser mounting area gt gt DECORATIVE RING L DIFFUSER RETAINING SCREWS J MOUNTING STUDS 0 FIGURE 3 NOT INCLUDED MOUNTING BAR A sy H lt OUTLET BOX J SCREWS R lt CANOPY D SCREW COLLAR E SCREW COLLAR RING F lt CHAIN G I in lt _ FIXTURE LOOP H DECORATIVE RING L DIFFUSER K FIGURE 2 NOT SUPPLIED
3. re or round and smooth tracer to the supply hot wire B Use a listed wire connector to connect the fixture common wire white wire or square and rigid to the supply common wire C Gently try to remove the wires from the connector If you can remove the wires carefully re do the wiring connection STEP 6 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire F from the fixture and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire F from the fixture and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 7 After wires are connected tuck them carefully inside outlet box and then raise the canopy D against ceiling and thread the screw collar ring F to the screw collar E to secure STEP 8 Install lamps not supplied STEP 9 Rest diffuser K on the inside lip of decorative ring L STEP 10 Raise decorative ring L to the fixture ring M so mounting studs O protrude through both rings Secure by threading retaining screws N onto mounting studs O STEP 11 Place washers over threaded h
4. sheet for future reference and in case you need to order i replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when oo LOOP H lt CHAIN 6 ordering parts BEFORE YOU BEGIN Carefully remove the fixture from the carton and check that all parts are included as shown in figure 1 Be careful not to misplace any of the screws or parts which are needed to install this fixture INSTALLATION IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Thread fixture loop H to fixture STEP 2 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 5 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Thread screw collar E to nipple C STEP 3 Using 2 pairs of pliers or chain breaks open one link of chain G and connect it to the fixture loop H at the top of the fixture Chain should be opened outward do not twist STEP 4 Slide the screw collar ring F and canopy D in that order over chain G Open one link on the other end of the chain G and attach it to the screw collar E which has been mounted to the ceiling FIGURE 1 NOT SUPPLIED nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY INSTALLATION continued HC 1435 STEP 5 A Use a listed wire connector to connect the fixture hot wire black wi
Download Pdf Manuals
Related Search