Sea Gull Lighting 3413-962 Installation Guide
Contents
1. and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 6 GROUNDING INSTRUCTIONS The green grounding screw R is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire S from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw R on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire S from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all UL specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires2. supplied Thread nut B on nipple C so that 3 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Attach screw collar D to nipple C STEP 2 Using 2 pairs of pliers open one link of chain G and connect it to the fixture loop I at the top of the fixture STEP 3 Slide the screw collar ring F and canopy E in that order over chain G Open one link on the other end of the chain G and attach it to the screw collar D which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 4 Lace wires up through chain G and pass wires through holes in screw collar D We recommend lacing wire up through every other link of chain G STEP 5 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED CI WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER SSS BROWN GOLD OR BLACK WITHOUT BROWN GOLD OR BLACK WITH TRACER TRACER SN Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire
3. X Installation And Safety Instructions FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER SET AT OFF WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY MOUNT TO OUTLET BOX OR SUPPORTING SYSTEM ABLE TO SUPPORT THE WEIGHT OF THE FIXTURE WIRE OUTLET BOX CONNECTORS GROUND WIRE OUTLET BOX SCREWS GROUND SCREW CHAIN G gt I COLLAR RING F FIXTURE LOOP I COLUMN H GLASS y lt IF APPLICABLE ARM ASSEMBLY J ROTATE CLOCKWISE BOBECHE T LOCK WASHER P gt LONG CENTER PIPE O COUPLING M i CENTER BODY ASSEMBLY K PIPE U BALL ASSEMBLY L o gt ROUND NUT W DECORATIVE LOOP X FIGURE 1 NOT INCLUDED HC 315 030200 Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician ASSEMBLY Carefully remove the fi
4. can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box and then raise the canopy E against ceiling and screw the screw collar ring F to the screw collar D STEP 2 Install candle covers Q if applicable STEP 3 Install lamps STEP 4 Install glass in holder if applicable CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
5. xture from the carton and check that all parts are included as shown in figure 1 and 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture NOTE If the following parts are not supplied or they are factory assembled proceed to the next assembly step Note Fixture may be partly assembled STEP 1 Pull the wires from coupling M in the following order through long center pipe O column H lock washer P bobeche T and fixture I Be careful not to pinch the wires Thread long center pipe O onto coupling M Over long center pipe O slide in the following order Column H bobeche T lock washer P and secure with the fixture loop l STEP 3 Thread short center pipe U to coupling N Over short center pipe U slide in the following order neck V two piece ball L and secure with round nut W Thread decorative loop X onto short center pipe U STEP 4 Turn each arm J clockwise 1 4 turn to be upward or downward see the style on carton if necessary Do not turn past upward position this will cause arm to loosen fe 5 GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX GROUND WIRE WIRE CONNECTORS OUTLET BOX SCREWS GROUNDING SCREW R FIGURE 2 NIPPLE C NOT INCLUDED INSTALLATION HC 315 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Secure mounting bar A to outlet box with outlet box screws not
Download Pdf Manuals
Related Search