Minka Lavery 1733-613 Instructions / Assembly
Contents
1. FIXTURE gt FIXTURE gt WIRES WIRES 3 BLACK OR GREEN OR ey SMOOTH BARE l HOUSE COPPER WIRES HOUSE GROUND HOUSE BLACK WIRES WIRES Har WHITE GREEN OR BARE NEUTRAL COPPER GROUND Notice It is aparani to use proper chain pliers not included to OPEN and CLOSE the chain included with this fixture Do not open them with other tools that may twist or stress the chain links It is important to use proper chain pliers like the ones shown in the is american lighting association intertek INSTALLATION INSTRUCTIONS _For Model 1733 5 613 167 Ff WARNING SHUT OFF THEI POWER AT FUSE OR CIRCUIT BREAKER CONNECTING THE WIRES Fig 3 14 At this point connect the electrical wire as shown in figure 3 making sure that all wire connectors are secured Wrap the fixture ground wire around the ground screw of the crossbar and then tighten the screw Connect the remaining fixture ground wire to the supply ground wire using a wire nut Otherwise connect the fixture Ground Wire directly to the crossbar using the Green Screw provided 15 Tuck these wire connections neatly into the ceiling junction box and then raise the canopy all the way to the ceiling Raise the Lock Collar W and thread onto ceiling Loop protruding through canopy 16 install the lamp on per the fixture s specification DO NOT EXCEED THE MAXIMUM WATTAGE RATING Your installation is now complete Return power to the2. ARSE DNG The Fixture See Fig 1 1 Carefully unpack your new fixture and put all the parts on a clear area Make sure not to misplace any parts which are necessary for installation Shut off the power supply at the fuse box or circuit breaker box Remove the old fixture from the wall including the old Crossbar Thread stem with hex nui F into coupling G then slide the tube C cap D tube C onto stem with hex nut F and secure them with knurled nui B then thread fixture loop Ajon Put the glass shade Ijonto socket H and secure it with socket ring J MOUNTING THE FIXTURE See Fig 2 1 Thread Nipple into Loop until snug 2 Thread other end of Nipple with Loop attached into crossbar until snug 3 Place Lock Washer over end of Nipple protruding through crossbar and thread Hex Nut onto nipple until tight 4 Take the crossbar assembly and mount fo ceiling junction box with junction box screws Tighten screws securely with screwdriver 5 By measuring determine correct number of links needed for proper hanging height 6 Attach one end of the chain to the chain link Slip Lock Collar and Canopy over the chain 7 Open the other end link of the chain and lift the fixture to attach ta the ceiling loop close the chain link 8 Lace the fixture s wires through the chain links and pull until taut Feed the fixture wires through the Loop and Nipple and pull until taut 25x U0 wats Type no to a
3. autlet box and test the fixture Junction Box Ceiling Chain Link Loop Loop Zg wXx IY KNURLED NUT B TO CAPM TUBE STEM WITH HEX NUTR Glass e aH SOCKET RING INSTALLATION INSTRUCTIONS Assembling The Fixture See Fig 1 1 Carefully unpack your new fixture and put all the parts on a clear area Make sure not to misplace any parts which are necessary for installation 2 Shut off the power supply at the fuse box or circuit breaker box Remove the old fixture from the wall including the old Crossbar 3 Thread stem with hex nul F into coupling G then slide the tube C cap D tube C onto stem with hex nut F and secure them with knurled nut B then thread fixture loop A on 4 Put the glass shade I onto socket H and secure it with socket ring J MOUNTING THE FIXTURE See Fig 2 Thread Nipple into Loop until snug 2 Thread other end of Nipple with Loop attached into crossbar until snug 3 Place Lock Washer over end of Nippie protruding through crossbar and thread Hex Nut onto nipple untif tight 4 Take the crossbar assembly and mount fo ceiling junction box with junction box screws Tighten screws securely with screwdriver 5 By measuring determine correct number of links needed for proper hanging height 6 Attach one end of the chain to the chain link Slip Lock Collar and Canopy over the chain 7 Open the other end link of the chain and dift the fixture to att
4. ach to the ceiling loop close the chain link 8 Lace the fixture s wires through the chain links and pull until taut Feed the fixture wires through the Loop and Nipple and pull until taut _ FIXTURE C gt WIRES ie i GREEN OR HOUSE BARE WIRES GREEN OR BARE COPPER GROUND FIXTURE lt WIRES ao WHITE OR KO RIBBED ae FIXTURE WIRES i H BLACK OR SMOOTH OUSE gt COPPER WIRES BLACK HOT HOUSE GROUND WIRES WHITE NEUTRAL Notice It is important to use proper chain pliers not included to OPEN and CLOSE the chain included with this fixture Do not open them with other tools that may twist or stress the chain links It is important to use proper chain pliers like the ones shown in the diagram american lighting association Intertek B For Model 1733 5 613 167 _ WARN ING SHUT OF F THE POWER AT FUSE OR CIRCUIT BREAKER CONNECTING THE WIRES Fig 3 14 At this point connect the electrical wire as shown in figure 3 making sure that all wire connectors are secured Wrap the fixture ground wire around the ground screw of the crossbar and then tighten the screw Connect the remaining fixture ground wire to the supply ground wire using a wire nut Otherwise connect the fixture Ground Wire directly to the crossbar using the Green Screw provided 15 Tuck these wire connections neatly into the ceiling junction box and then raise the canopy ail the w
5. ay to the ceiling Raise the Lack Collar W and thread onto ceiling Loop protruding through canopy 16 Install the Jamp on per the fixture s specification DO NOT EXCEED THE MAXIMUM WATTAGE RATING Your installation is now complete Return power to the outlet box and test the fixture Junction Box Ceiling O FIXTURE LOOA KNURLED NUT B mo CAPE TUBE STEM WITH HEX NUTR ACCOM SOCKET RINGN in GLASS SHADED COUPLING G ST SOCKET H
Download Pdf Manuals
Related Search