Home
Westinghouse 7802400 Installation Guide
Contents
1. Attach blade brackets to blades using the blade bracket screws 1 and fabric washers 2 Fije os soportes para aletas a las aletas con los tomillos 1 y las arandelas de tela 2 Check the motor for plastic shipping stabilizer tabs 1 and remove them if they are present Attach blade assembly to motor using the noise dampening motor gaskets 2 and motor screws provided Tighten screws securely NOTE Some models do not utilize motor gaskets washers or stabilizer tabs Verifique si hay lengiietas pl sticas de embalaje para sostener al motor 1 y desc rtelas Fije el conjunto de las aletas al motor usando las juntas reductoras de sonido del motor 2 y los tomillos para el motor incluidos Apriete los tornillos lasegur ndolos NOTA Algunos modelos no utilizan juntas para el motor arandelas o leng etas de embalaje Assemble decorative fob and extension chains from hardware bag to fan pull chains by inserting end of chain into chain coupling Confirm chains are held by lightly pulling both chains in coupling Conecte las cadenilla de tiro con las piezas finales correspondientes a las cadenas del ventilador introduciendo el extremo de la cadenilla de tiro a la pieza de uni n Aseg rese de que las cadenas est n bien sujetas tirando ligeramente de ambas cadenas por la pieza de uni n 16 ETL ES Contractors R WH14 OPERATION AND MAINTENANCE O E EA Operation Tum on the power and che
2. the mounting bracket Para ventiladores de instalaci n al ras levante con cuidado el ventilador del soporte de montaje asegur ndose de que no interrumpa ninguna conexi n de los cables Para ventiladores con varilla vertical deslice el dosel hacia arriba hasta el soporte de montaje The canopy has two mating slots 1 and two mating holes 2 Position both slots on canopy directly under and in line with two screws in the mounting bracket 3 Lift the canopy allowing the two screws to slide into the mating slots Rotate the canopy clockwise until both screws from the mounting bracket drop into the slot recesses Tighten screws securely Install two screws and lock washers into the mating holes of the canopy and tighten to secure the canopy to the mounting bracket El dosel tiene dos ranuras coincidentes 1 y dos agujeros coincidentes 2 Coloque ambas ranuras del dosel directamente abajo y en l nea con los dos tornillos del soporte de montaje 3 Eleve el dosel permitiendo que los dos tornillos se deslicen dentro de las ranuras Gire el dosel en sentido horario hasta que ambos tornillos del soporte de montaje caigan adentro de las ranuras Apriete los tornillos asegur ndolos Instale los dos tornillos y las arandelas de presi n en estrella en los orificios coincidentes del dosel y aj stelos para asegurar el dosel al soporte de montaje 15 BLADE INSTALLATION INSTALACION DE LAS PALETAS ETL ES Contractors R WH14
3. Afloje no quite los tornillos de las ranuras coincidentes 2 del dosel Gire el soporte de montaje en sentido contrario a las agujas del reloj y extr igalo del dosel MOUNTING BRACKET INSTALLATION INSTALACI N CON SOPORTE DE MONTAJE Install mounting bracket to outlet box in ceiling using the screws and washers provided with the outlet box Instale el soporte de montaje a la caja de embutir del techo con la torniller a suministrada con la caja de embutir ETL ES Contractors R WH14 __ MOUNTING OPTIONS OPCIONES DE MONTAJE Choose a MOUNTING OPTION Elija una OPCION DE MONTAJE FLUSH MOUNT OPTION lf flush mount option is selected proceed to page 9 step 6 OPCION DE INSTALACION AL RAS Si elige la opci n de montaje al ras proceda a la p gina 9 paso 6 NORMAL DOWNROD OPTION OPCI N CON VARILLA VERTICAL PARA CIELORRASO NORMAL Si instala la varilla vertical incluida con el ventilador proceda a la p gina q0 paso 8 EXTENDED DOWNROD OPTION Ifinstalling with longer downrod than supplied with fan proceed to page 10 step 9 OPCION CON VARILLA VERTICAL MAS LARGA Si instala una varilla vertical m s larga de la que se incluye con el ventilador proceda a la p gina 10 paso 9 Deslice los cables del motor a trav s de la base del dosel como se it ETL ES Contractors R WH14 FLUSH MOUNT OPTION OPCI N DE INSTALACI N AL RAS Guide motor wires thro
4. ETL ES Contractors R WH14 PREPARING FOR INSTALLATION ANTES DE LA INSTALACION Unpack and inspect fan carefully to be certain all contents are included Turn off power at fuse box to avoid possible electrical shock que todas las piezas est n incluidas Apague la alimentaci n en la caja de fusibles para evitar la posibilidad de descarga el ctrica Quite el envoltorio e inspeccione detenidamente el ventilador para verificar Use metal outlet box suitable for fan support must support 35 Ibs Before attaching fan to outlet box ensure the outlet box is securely fastened by at least two points to a structural ceiling member a loose box will cause the fan to wobble Use una caja de embutir de metal adecuada para soportar un ventilador debe soportar 35 libras Antes de fijar el ventilador a la caja de embutir aseg rese de que la misma est fijada de manera segura en por lo menos dos puntos a un miembro estructural del techo una caja suelta har a que el ventilador oscile ETL ES Contractors R WH14 ao MOUNTING BRACKET INSTALLATION oo INSTALACI N CON SOPORTE DE MONTAJE Remove the screws and star washers from the two mating holes 1 on the canopy Loosen do not remove the screws in the mating slots 2 on the canopy Rotate the mounting bracket counter clockwise and remove from the canopy Quite los tomillos y las dos arandelas en estrella de los dos agujeros coincidentes 1 del dosel
5. ck operation of fan The pull chain controls the fan speeds as follows 1 pull high 2 pulls medium 3 pulls low 4 pulls off Speed settings for warm or cool weather depend on factors such as room size ceiling height number of fans and so on The side switch controls direction forward or reverse Warm weather down position Forward Fan tums counterclockwise direction A downward air flow creates a cooling efect as shown in illustration A This allows you to set your air conditioner on a higher temperature setting without affecting your comfort ool weather up position Reverse Fan tums clockwise direction An upward airflow moves warm air off the ceiling area as shown in illustration B This allows you to set your heating unit on a lower setting without affecting your comfort NOTE Tum off and wait for fan to stop before changing the setting of the forward reverse slide switch Maintenance 1 Because ofthe fans natural movement some connections may become loose Check the support connections brackets and blade attachments twice a year Make sure they are secure Clean your fan periodically to help maintain its new appearance over the years Do not use water when cleaning This could damage the motor or the wood or possibly cause electrical shock j Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer coating to minimize discoloration or tamishing gt There is no nee
6. d to oil your fan The motor has permanently lubricated bearings 17 ETT gt ANA
7. or wall control operation NOTE A professional electrician is recommended for this type of installation OPCI N DE CABLEADO PARA CADENILLA DE TIRO Del Ventilador De La Casa Blanco com n conoce Blanco com n Negro vivo HE conecte m Negro vivo Azul vivo mm Verde de tierra 553 conecte sex Verde de tierra Mane abl zl silo conc un juego de luces al ventilador Siga las instrucciones del diagrama anterior para hacer las conexiones de cableado para el ventilador controlado con cadenilla de tiro OPCI N DE CABLEADO PARA CONTROL DE PARED Del Ventilador De La Cosa Negro vivo mmm conecte H Interruptor del ventilador vivo n Azul vivo mmm conecte gt I Interruptor de la luz vivo Verde de terra exist conecte Verde de tierra Blanco com n gt leonec gt Blanco com n Con depod Conecte el able agu slo si conecta un juego de luces al ventilador Siga la instrucciones del diagrama anterior para hacer las conexiones de cableado para el ventilador con control de pared NOTA Se recomienda que use los servicios de un electricista profesional para este tipo de instalaci n 14 ETL ES Contractors R WH14 ce SECURE TO CEILING ASEGURE EL VENTILADOR AL TECHO For flush mount fans carefully lift fan from the mounting bracket making sure not to break any wire connections 1 7 For downrod fans slide the canopy up to
8. te los tomillo de fijaci n 3 en la horquilla 12 ETL ES Contractors R WH14 MOUNTING MONTAJE Carefully lift fan assembly onto mounting bracket Rotate fan until notch on downrod ball 1 engages the ridge on the mounting bracket 2 This ill allow for hat iri ij hasta el soporte de ji Gire el ventilador hasta que la muesca de la bola de la varilla vertical 1 enganche sobre la saliente del soporte de montaje 2 De este modo tendr las dos manos libres para hacer el cableado K tand entilador conexiones el ctricas de acuerdo a las siguientes instrucciones de cableado 13 ETL ES Contractors R WH14 WIRING OPTIONS OPCION DE CABLEADO PULL CHAIN WIRING OPTION 15 From Fan From House White common tomec White common Black hot mmm connect gt m Black hot Blue hot mmm a Green ground 8 connect gt ea Green ground Connect blue wie only if attaching light kit with fan Follow diagram above to make wiring connections for fan pull chain control 16 WALL CONTROL WIRING OPTION From Fan From House White common connect gt White common Black hot mmm connect gt m Fan Switch hot Blue hot cam connect gt m Light Switch hot Green ground Ez connec gt m Green ground Connect blue wie only if attaching light kit with fan Follow diagram above to make wiring connections f
9. ugh the base of the canopy as shown Attach canopy to motor housing using three flush mount screws and lock washers previously removed Tighten screws securely al alojamiento del motor con los tres tornillos de montaje al ras y las arandelas de presi n que extrajo previamente Apriete los tomillos asegur ndolos Forflush mount option raise fan assembly and place onto hook 1 from mounting bracket into a dosed hole on the canopy This will allow for hands free wiring PROCEED DIRECTLY TO PAGE 14 FOR WIRING OPTIONS Para la opci n de montaje al ras levante el montaje del ventilador col quelo sobre el gancho 1 del soporte de montaje y cu lguelo en uno de los agujeros cerrados del dosel De este modo tendr las dos manos libres para hacer el cableado PARA LAS OPCIONES DE CABLEADO PROCEDA DIRECTAMENTE A LA PAG 14 NORMAL DOWNROD OPTION _ OPCION CON VARILLA VERTICAL PARA CIELORRASO NORMAL a 7 VA yoke PROCEED TO PAGE 13 STEP 13 enla horquilla PROCEDA A LA PAG 13 PASO 13 Make sure to align hole in downrod with the hole in downrod yoke Install yoke cross pin 1 through yoke and downrod Insert damp pin 2 into cross pin until it snaps into place Tighten set screws 3 in Deslice los cables del motor a trav s de la varilla vertical conjunto del dosel e inserte la varilla vertical en la horquilla de la misma Aseg rese de que el agujero de la varilla vertical
10. uperior de la misma Vuelva a insertar el tornillo de fijaci n para asegurar la bola a la varilla vertical Nota Algunas varillas verticales m s largas tienen un agujero previamente perforado para el tomillo Si la varilla vertical m s larga tiene un agujero previamente perforado ajuste el tomillo en el agujero previamente perforado de la varilla vertical m s larga Si la varilla vertical m s larga no tiene un agujero previamente perforado ajuste el tornillo sobre la varilla vertical para asegurar la bola de la misma 11 ETL ES Contractors R WH14 amaia EXTENDED DOWNROD OPTION oo OPCION CON VARILLA VERTICAL MAS LARGA Feed motor lead wires through downrod canopy assembly and insert downrod into downrod yoke Make sure to align hole in downrod with the hole in downrod yoke Install yoke cross pin 1 through yoke and downrod Insert clamp pin 2 into cross pin until it snaps into place Tighten set screws 3 in yoke Deslice los cables del motor a trav s de la varilla vertical conjunto del dosel e inserte la varilla vertical en la horquilla de la misma Aseg rese de que el agujero de la varilla vertical y el de la horquilla de la varilla vertical est n alineados Instale el pasador transversal de la horquilla 1 pas ndolo por la horquilla y la varilla vertical Inserte el pasador de fijaci n 2 en el pasador transversal hasta que escuche un chasquido que indique que est en la posici n adecuada Ajus
11. y el de la horquilla de la varilla vertical est n alineados Instale el pasador transversal de la horquilla 1 pas ndolo por la horquilla y la varilla vertical Inserte el pasador de fijaci n 2 en el pasador trans versal hasta que escuche un chasquido que indique que est en la posici n adecuada Ajuste los tomillos de fijaci n 3 ETL ES Contractors R WH14 EXTENDED DOWNROD OPTION OPCI N CON VARILLA VERTICAL M S LARGA Loosen downrod ball 1 from downrod 2 by removing set screw 3 Afloje la bola de la varilla vertical 1 de la varilla vertical 2 quitando el tornillo 3 10 ETL ES Contractors R WH14 EXTENDED DOWNROD OPTION OPCI N CON VARILLA VERTICAL M S LARGA Slide downrod ball 1 off of downrod and remove pin 2 Deslice la bola de la varilla vertical 1 hasta separarla de la varilla vertical y quite el pasador 2 Re install pin into extended downrod and slide downrod ball up to the top of the downrod Re install set screw to secure ball to downrod Note Some extended downrods have a pre drilled set screw hole If a pre drilled hole is present in the extended downrod tighten the set screw into the pre drilled hole in the extended downrod If no pre drilled hole exists in the extended downrod tighten the set screw against the downrod to secure the downrod ball Vuelva a instalar el pasador en la varilla vertical m s larga y deslice la bola de la varilla hasta el extremo s
Download Pdf Manuals
Related Search
Related Contents
USER GUIDE Philips Sonicare e-Series Compact sonic toothbrush heads HX7004/16 405777-0126-E1 Sélection: Arbre à cames Télécharger le mode d`emploi 2015 Manual de instruções ICA512-4BR1 Pdf 305.58 KB Manual de instalación y operación Bluetooth Kopfhörer 10011115 10011116 10011117 Copyright © All rights reserved.
Failed to retrieve file