Minka Lavery 4877-283 Instructions / Assembly
Contents
1. INSTALLATION INSTRUCTIONS Item 4877 283 New 05 10 2014 READ AND SAVE THESE INSTRUCTIONS WARNING SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER ERTISSEMENT COUPER i Ao N ao 1 2 3 4 o 8 9 ASSEMBLING THE FIXTURE Fig 2 HANGING THE FIXTURE Fig 1 10 12 Shut off the power at the fuse box or circuit breaker If necessary remove the existing fixture and its mounting hardware from the ceiling Carefully remove the new fixture from the carton and check that all parts are included as shown in the illustration Remove the screw K and remove the outer frame N Insert glass L into the outer frame N and secure the glass with clips M Place the fixtur body J ifito the outer frame N and secure with screws K Secure fixture loop to nipple on top of the fixture body J Install the light bulbs not included in accordance with the fixture s specifications DO NOT EXCEED THE MAXIMUM WATTAGE RATING NE MX ob uel LA PUISSANCE NOMINALE MAXIMALE XOD watts Type B Thread nipple C into ceiling loop F until snug Thread the other end of nipple C with loop attached into crossbar D until snug Place lock washer B and hex nut A over end of nipple protruding through crossbar Then thread hex nut A until tight Take this crossbar assembly and mount to the ceiling outlet box using outlet box screws E Size 8 32N L0 5 The side of the cross2. 12 At this point connect the fixture wires as shown in Fig 3 making sure that all wire connectors are secured If your outlet box has a ground wire green or bare copper connect the fixture s ground wire to it Otherwise connect the fixture s ground wire directly to the crossbar D using the green screw provided Tuck these wire connections neatly into the ceiling outlet box and raise the canopy G to the ceiling Then raise the lock collar H and thread onto the ceiling loop F protruding through the canopy Your installation is now complete Return power to the outlet box and test the fixture Note Illustration Fig 1 Fig 2 on this manual is for installation purposes only it may or may not be identical to the fixture purchased Fig 1 Set A 016 Crossbar Ground Screw Mounting Screw 2 Fig 2 Chain HCH2072 283 Gauge D3 8mm CHAIN HUNG FIXTURE INSTRUCTION Notice It is important to use proper chain pliers not included To OPEN and CLOSE the chain included with this fixture Do not open them with other tools that may twist or stress the chain links It is important to use proper chain pliers like the ones shown in the diagram SC Fig 3 FIXTURE FIXTURE WIRES 5 WIRES Black or An White or Smooth HOUSE Ribbed WIRES Black Hot 5 Copper BS HOUSE Ground HOUSE WIRES WIRES White Green or Neutral Bare Copper Ground
3. Ds Ceaper Intertek
4. CHAIN HUNG FIXTURE INSTRUCTION Notic It is important to use proper chain pliers not included To OPEN and CLOSE the chain included with this fixture Do not open them with other tools that may twist or stress the chain links It is important to use proper chain pliers like the ones shown in the amp iG 20 30X18 50X26 77 INCHES NW 10 32 kas Gale 13 31 Kas U NIVEAU DES FUSIBLES OU DU DISJONCTEUR B o x2 H Set A 016 Crossbar Ground Screw Mounting Screw 2 wx he Glass Q n Hwxl4 Ah Figg lop SOLERE PER Chain HCH2072 283 Gauge D3 8mm gt a lighti association ng e s Fig 3 me FIXTURE z MIRES Black or 7 Smooth ees 2 HOUSE Ground HOUSE WIRES v Black White Green or Hot Neutral Bare Copper Ground american K US rst Intertek INSTALLATION INSTRUCTIONS Item 4877 283 New 05 10 2014 READ AND SAVE THESE INSTRUCTIONS 4 AO N or ie ASSEMBLING THE FIXTURE Fig 2 Shut off the power at the fuse box or circuit breaker If necessary remove the existing fixture and its mounting hardware from the ceiling Carefully remove the new fixture from the carton and check that all parts are included as shown in the illustration Remove the screw K and remove the outer frame N Insert glass L into the outer frame N and secure the glass with clips M Place the fixture body J
5. into the outer frame N and secure with screws K Secure fixture loop to nipple on top of the fixture body J Install the light bulbs not included in accordance with the fixture s specifications DO NOT EXCEED THE MAXIMUM WATTAGE RATING NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE HANGING THE FIXTURE Fig 1 4 2 3 4 a x9 9 10 Thread nipple C into ceiling loop F until snug Thread the other end of nipple C with loop attached into crossbar D until snug Place lock washer B and hex nut A over end of nipple protruding through crossbar Then thread hex nut A until tight Take this crossbar assembly and mount to the ceiling outlet box using outlet box screws E Size 8 32N L0 5 The side of the cross marked GND must face out Using a pair of chain pliers open one end link of the chain and connect to the fixture loop I Then close the link Carefully lace the fixture wires through the chain By measuring determine the correct number of links needed for the desired hanging height Using the chain pliers disconnect and discard the excess chain Slip the lock collar H and canopy G over the chain allowing them to rest onto the fixture loop 1 Open the other end link of the chain and attach it to the ceiling loop F Then close the link Feed the fixture wires through the ceiling loop F and nipple C and pull tight CONNECTING THE WIRES Fig 3 11
6. marked GND must face out Using a pair of chain pliers open one end link of the chain and connect to the fixture loop I Then close the link Carefully lace the fixture wires through the chain By measuring determine the correct number of links needed for the desired hanging height Using the chain pliers disconnect and discard the excess chain Slip the lock collar H and canopy G over the chain allowing them to rest onto the fixture loop I Open the other end link of the chain and attach it to the ceiling loop F Then close the link Feed the fixture wires through the ceiling loop F and nipple C and pull tight CONNECTING THE WIRES Fig 3 11 At this point connect the fixture wires as shown in Fig 3 making sure that all wire connectors are secured If your outlet box has a ground wire green or bare copper connect the fixture s ground wire to it Otherwise connect the fixture s ground wire directly to the crossbar D using the green screw provided Tuck these wire connections neatly into the ceiling outlet box and raise the canopy G to the ceiling Then raise the lock collar H and thread onto the ceiling loop F protruding through the canopy Your installation is now complete Return power to the outlet box and test the fixture i Note Illustration Fig 1 Fig 2 on this manual is for installation purposes only It may or may not be identical to the fixture purchased diagram
Download Pdf Manuals
Related Search