Home

TroposAir 88801 Installation Guide

1. Owner s Manua roposir ProSeries Builder Outdoor This instruction contains 6 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation Page 3 5 Hanging system installation Page 5 Wire and Canopy installation Page 6 Blade and Pull Chain Knob installation Net weight UL 6 0 KGS ENERGY STAR 13 2 LBS PARTNER Toll Free 1 855 676 7247 WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades should be at least 7 feet
2. ain Knob 6 Turn on the power at breaker box your fan is ready for operation P6
3. box must support 35 Ibs min 1 HANGING SYSTEM INSTALLATION 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and washers from the hardware bag Outlet Box gt Mounting gt 4a Bracket 1B This fan has two installation methods available Downrod mount Standard Please follow up Step 1C and 1D Flush mount Hugger Please directly go to Step 1E and 1F Downrod mount Flush mount See Step 1C and 1D See Step 1E and 1F 1C Installing Downrod and Yoke Remove cross pin and cotter pin from downrod Remove the pre attached Gasket from the downrod assembly and keep for Step Insert downrod through canopy and yoke cover and feed motor lead wires through downrod Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke Q Gasket EDSN Removing CD Downrod Cross Pin Yoke cover AA P3 1C Continued Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod Pull down the yoke cover to cover yoke Insert 4 wires and through holes of Gasket Removed from Step and put the Gasket back into downrod assembly Downrod Assembly 1D Hanging the fan For Downrod mount Lift fan assembly onto mounting
4. bracket Rotate fan so that the groove on the ball engages the ridge in the mounting bracket Mounting Bracket Mounting Bracket 1E Canopy Assembly For Flush mount Note There are three big screws and three small screws pre attached on top of fan assembly Remove three big screws with washers and keep them for Step Remove canopy decorating cap from bottom of canopy Put the canopy onto yoke and fasten with three big screws with washers removed from Step Big Screw amp Washer 3 gt Canopy decorating cap Big Screw amp Washer 3 Small Screw amp Washer 3 Top of Fan Housing Fan assembly 4 Ts P4 1F Hanging the fan For Flush mount Lift the fan assembly and hang onto the tab on mounting bracket Note This will permit you to make the wire connections without having to hold the fan up as well l i T E Q Mounting Bracket 0 Fan assembly 2 WIRE CONNECTION Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block Note Wires from house may vary in color and may not include ground wire green White wire from house to white wire from fan Black wire from house to black wire and blue wire from fan Ground wire from house to green wire from downrod and from mounting bracket Secure with twist lock wire nuts Included After
5. from floor when fan is in operation 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight 4 of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side 7 Electrical diagrams are for reference only Light kits that are not packed with the fan must be UL ETL listed and should be installed per the light kit s installation instructions 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be made to work immediate
6. ly after installation The bearings are adequately charged with grease so that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 This fan is suitable for three mounting ways Downrod standard Flush Hugger Slope ceiling 12 This fan is reversible 13 This fan is light kit adaptable 14 This fan is remote adaptable 15 This fan is suitable for wet location use P1 Unpack and inspect fan carefully to be certain all contents are included Mounting Bracket Hardware Bag For Mounting Bracket Flat Washer x2 Spring Washer x2 Downrod l Assembly Machine Screw x2 Wood Screw x2 For Wire Connection Wire Nut x 3 4 8 4a For Blade Installation Canopy gt Blade Screw x 16 one spare screw included TETTETETT FED R n a PEP RF Canopy Rubber Washer x 16 one spare washer included Decorating Cap o o ooo oo e 2o ooo Yoke cove f Motor Screw x 11 one spare screw included O O O O O O Wires For Fan G gt LEF Pull Chain Knob x1 For Blade Balance Balancing slide x 1 Weight block 3G x 3 e 2 P2 WARNING blades should be at least 7 feet from floor Note 1 Note 2 Turn off power at breaker Use metal outlet box suitable box to avoid possible for fan support electrical shock Outlet
7. wiring is completed gently push wires into junction box with wire nuts pointing upward Wire Form House From House From Fan White Sess a White AC N MOTOR N Black gt Black AC L MOTOR L Blue For Light Kit Green T g Green for ground wire R a Green Outlet Box from mounting bracket Secure with twist lock wire nuts Note Four screws are pre screwed on mounting bracket for canopy installation Remove left hand side screw on mounting bracket first and loosen the other one Note Please do the same for the other two screws on the across side of mounting bracket Rotate the canopy slightly until both two loosening screws are in the holes of L type slots Tighten 4 screws firmly L Type Slots Screw 4 P Tightening Left hand side screw Removing Loosening P5 4 BLADE INSTALLATION Attach blade to blade holder with 3 blade screws and 3 rubber washers provided from hardware bag Make sure all screws are firmly tightened Remove 3 motor stoppers by removing screws G Secure Blade Assembly to the motor with 2 motor screws provided from hardware bag NOTE To prevent wobble do not bend blade or blade holder Blade Screw 3 gt Motor Stopper 3 Rubber Washer 3 gt _4 Blade Holder Switch Housing i Pull Ch

TroposAir 88801 Installation Guide

Contents

Download Pdf Manuals

Related Search

Related Contents