TroposAir 88900 Instructions / Assembly
Contents
1. Owner s Manua roposir Saturn 5DA52 This instruction contains 6 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation Page 3 4 Hanging system installation and Wire connection Page 5 Canopy Blade Switch Housing installation Page 6 Pull Chain Knob installation E Net weight A q Com 8 5 KGS _ste RESAN 18 7 LBS a Toll Free 1 855 676 7247 WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades shou2. bly onto mounting bracket Rotate fan so that the groove on the ball engages the ridge in the mounting bracket Mounting Bracket Mounting Bracket 1E Canopy Assembly For Flush mount 1F Hanging the fan For Flush mount Remove canopy decorating cap from bottom of canopy Lift the fan assembly and hang onto the tab on Fasten 3 canopy set screws provided from hardware bag mounting bracket onto fan assembly firmly Note This will permit you to make the wire connections without having to hold the fan up as well Canopy set screw 3 gt o Mounting 2 Bracket Canopy Canopy Y decorating cap J Fan assembly s Fan assembly 2 WIRE CONNECTION Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block Note Wires from house may vary in color and may not include ground wire green White wire from house to white wire from fan Black wire from house to black wire and blue wire from fan Ground wire from house to green wire from downrod and from mounting bracket Secure with twist lock wire nuts Included After wiring is completed gently push wires into junction box with wire nuts pointing upward Wire Form House From House From Fan Outlet Box White S amp ose AC N Black EE ax AC L MOTOR N MOTOR L cy For Li
3. ght Kit Green from downrod for ground wire from mounting bracket Secure with twist lock wire nuts P4 3 CANOPY INSTALLATION Push up the canopy till center hole of canopy is engaged with spring tab of mounting bracket Secure canopy to mounting bracket with four canopy set screws and Spring Washers provided from hardware bag for further security Mounting Bracket Canopy Set Screw 4 Spring Washer 4 Spring Tab Center Hole 4 BLADE INSTALLATION Attach blade to blade holder with 4 blade screws and 4 flat washers provided from hardware bag Make sure all screws are firmly tightened Remove 3 motor stoppers by removing screws Secure Blade Assembly to the motor with 2 motor screws provided from hardware bag NOTE To prevent wobble do not bend blade or blade holder Fan assembly Blade Screw 4 Flat Washer 4 gt Blade Holder Remove 3 set screws from switch housing cover and keep them for Step Fasten switch housing and the cover together with 3 set screws removed from Step Switch Housing amp Switch Housing Cover Screw 3 P5 6 PULL CHAIN KNOB INSTALLATION Connect Pull Chain Knob provided from hardware bag to the pull chain from switch housing Fan Assembly 7 Turn on the power at breaker box your fan is ready for operation P6
4. ld be at least 7 feet from floor when fan is in operation 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight 4 of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side 7 Electrical diagrams are for reference only Light kits that are not packed with the fan must be UL ETL listed and should be installed per the light kit s installation instructions 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be
5. made to work immediately after installation The bearings are adequately charged with grease so that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 This fan is suitable for three mounting ways Downrod standard Flush Hugger Slope ceiling 12 This fan is reversible 13 This fan is light kit adaptable 14 This fan is remote adaptable 15 This fan is suitable for indoor use P1 Unpack and inspect fan carefully to be certain all contents are included Mounting Hardware Bag Bracket For Mounting Bracket Flat Washer x2 Spring Washer x2 Downrod Machine Screw x2 Wood Screw x2 Assembly For Wire Connection Wire Nut x 3 4 4 4 For Flush Mount Only Canopy Set Screw x 3 PF PP T Z For Canopy Installation Canopy Canopy SetScrewx4 FP F F P Decorating Cap Spring Washerx4 For Blade Installation Blade Screw x 21 one spare screw included TTT TTT TETTETETT TETTETETT TP Flat Washer x 21 one spare washer included Motor Screw x 11 one spare screw included O CG O OO Pull Chain Knob x1 For Fan For Blade Balance Balancing slide x 1 A Weight block 36x3 ODO D Blade x5 Blade Holder x P2 WARNING blades should be at least 7 feet from flo
6. or Note 1 Note 2 Turn off power at breaker Use metal outlet box suitable box to avoid possible for fan support electrical shock Outlet box must support 35 Ibs min 1 HANGING SYSTEM INSTALLATION 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and washers from the hardware bag Outlet Box gt Mounting gt 4a Bracket 1B This fan has two installation methods available Downrod mount Standard Please follow up Step 1C and 1D Flush mount Hugger Please directly go to Step 1E and 1F Downrod mount Flush mount See Step 1C and 1D See Step 1E and 1F 1C Installing Downrod and Yoke Remove cross pin and cotter pin from downrod Insert downrod through canopy and yoke cover and feed motor lead wires through downrod Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod Pull down the yoke cover to cover yoke g Downrod Cross Pin Cotter Pine a Downrod Jam 8 canopy D q Downrod Jam EE Screw 2 Screw 2 Loosening g Tightening Yoke cover Dp E Ajquassy lt pojumoq 1D Hanging the fan For Downrod mount Lift fan assem
Download Pdf Manuals
Related Search