Lithonia Lighting IB 632 MVH Installation Guide
Contents
1. Installation Instructions Il WW BE I BEAM FLUORESCENT HIGH BAY LIGHTING READ AND FOLLOWALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFETY INSTRUCTIONS A WARNING To reduce the risk of death injury or property damage from fire electric shock cuts abrasions falling parts and other hazards e Service of the equipment must be performed by qualified service personnel e Installation and maintenance must be performed by a person familiar with the construction and operation of this product and any hazards involved All applicable codes and ordinances must be followed Read this document before installing servicing or maintaining this equipment or installing a lamp These instructions do not cover all installation service and maintenance situations If your situation is not covered or if you do not understand these instructions or additional information is required contact Lithonia Lighting or your local Lithonia Lighting Distributor Read and follow all warnings and instructions provided by the lamp manufacturer WARNING Before installing servicing or maintaining this equipment follow these general precautions To reduce the risk of electrocution e Make sure the equipment is properly grounded e Always de energize the circuit and or equipment before connecting to disconnecting from or servicing the equipment To reduce the risk of fire e Keep material2. away that can burn from hot lamp e Make sure lamps are correctly installed e Use supply conductors with a minimum installation temperature rating as specified on equipment To reduce the risk of personal injury from cuts abrasions or falling parts e Wear gloves to prevent cuts or abrasions from sharp edges when removing from carton handling and maintaining this equipment Do not use abrasive materials glass cleaners or other solvents on reflector or lens These substances may damage equipment and cause parts to eventually break and fall Do not install a damaged fixture CAUTION Observe lamp manufacturer s recommendations and restrictions on lamp operation including but not limited to ballast type burning position replacement and cycling Use only lamps that comply with applicable ANSI standards NOTICE lf lamp is marked Hg it contains mercury Follow disposal laws See www lamprecycle org Lithonia Lighting a division of Acuity Brands Lighting Inc assumes no responsibility for claims arising out of improper or careless installation or handling of this product SAVE THESE INSTRUCTIONS 8 INDUSTRIAL VALUE STREAM Part Number U21293 LITHONIA LIGHTING One Lithonia Way Conyers GA 30012 Revision Date 10 2007 h lt Phone 800 315 4963 Fax 770 981 8141 AnSAcuityBrands Company www lithonia com Installation Instructions BEAM TROUBLE SHOOTING If this fixture fails to operate properly check to make sure T
3. MPS ON OM 3 LAMPS OM CFF 1 LAMPS ONM Fig 5 LINE HO LIME NEU 5 S LAMPS ON 4 LAMPS ON OFF 2 LAMPS ON ORANGE Lane BLUE E BR OWA _ Lara BLUESYVH I U j AnSAcuityBranas Company A gt 4ubUGTRinc VALUESTREAM n l LITHONIA LIGHTING alina comes Qm s n Phone 800 315 4963 Fax 770 981 8141 www lithonia com
4. he Correct lamp is properly installed The fixture is wired correctly The lamp is not faulty The fixture is grounded correctly The line voltage at the fixture is correct l BEAM INSTALLATION INSTRUCTIONS INSTALLATION OF THIS FIXTURE INANY OTHER MANNER THAN WHAT IS INDICATED WITHIN THE SUPPLIED INSTRUCTIONS WILL VOID ALL WARRANTIES These instructions are for NORMAL On Off operations Remove fixture from packaging Ensure proper voltage will be supplied to the fixture Check the fixture label on the carton for fixture voltage FIXTURE MUST BE GROUNDED BEFORE USE Picture 1 WIRING OF FIXTURE 1 Remove back access plate by removing 1 phillips screw Retain the screw and access plate for re installation Picture 1 Picture 2 i i T A I LE w i i r j i 7 i I ii L fr sh W i a K u D R N ee _ u i 1 i i F t fi i 3 Attach the conduit connector to the access plate in accordance with your local electrical code Push the wires through the knock out on the access plate and wire to the supply wire as shown in pictures 3 and 4 Ensure wires are not being pinched Make all necessary wiring connections observing proper voltage and polarity 2 Remove the twist tie and separate the wires Picture 2 4 Center the access plate to the back of the fixture Re attach the access plate A o 4NDUGTRIAE VALUE STREAM Pan NUDE ee s LITHONIA LIGHTING ha
5. lun Comes ma s Phone 800 315 4963 Fax 770 981 8141 www lithonia com AnSAcuityBrands Company s Installation Instructions Wa i P AM I BEAM FLUORESCENT HIGH BAY LIGHTING INSTALLING BATTERY PACK SUPPLIED WITH THE FIXTURE NOTE BATTERY PACKS SUPPLIED WITH 6 LAMP T5 LAMPS WILL NOT BE INSTALLED IN THE FIXTURE THE BATTERY IS EXTERNALLY MOUNTED ON THE BACK SIDE OF THE CHANNEL Battery unit comes with Pilot light Test Switch connector disconnected to prevent shock and battery discharge 1 Plug positive end of battery wiring harness to positive end of fixture wiring harness Harness is accessible through the open hole on the back of the fixture 3 Verify battery operation by engaging pilot light test switch If wired correctly 1 lamp will illuminate Keeping battery in the battery box secure box to back of channel with the 4 screws provided Do not over tighten Over tightening will cause stripping and void all warranties ithonia Lighting L ITHONIA LIGHTING INDUSTRIAL VALUE STREAM Part Number U21293 One Lithonia Way Conyers GA 30012 Revision Date 10 2007 v Phone 800 315 4963 Fax 770 981 8141 AnSAcuityBrands Company www lithonia com Installation Instructions BEAM E s i k Li L k L AAA LLLI FLUORESCENT HIGH BAY LIGHTING WIRING INFORMATION STANDARD WIRING LIME HOT LIME NEL S LAMPS LAMP SWITCHING WIRING ON 3 LAMPS ON OFF 2 LA
Download Pdf Manuals
Related Search