Lithonia Lighting DSXF3 LED 6 40K YKC62 Installation Guide
Contents
1. the access cover plate to the integral wiring compartment using a 1 4 hex socket or regular screwdriver Slip integral slipfitter onto tenon ensuring that the wires are pulled through the integral wiring compartment without pinching Secure the slipfitter to the tenon by tightening the 3 16 hex socket set screws To adjust the tilt angle of the fixture loosen the 5 16 hex socket screw above the integral wiring compartment Adjust as necessary and retighten Make supply connections through the integral wiring compartment Push wires into compartment Re install the access cover plate DSXF1 integral slipfitter DSXF2 integral slipfitter DSXF3 integral slipfitter 1 2 14 NPS Tenon Slipfitter DSXF1 2TS Installation T Light Engine Maintenance for use with THK mounting option THE FIXTURE SHOULD NOT BE ENERGIZED DURING ANY ELECTRICAL WORK Attach DSXF1 2TS to fixture s threaded 1 2 knuckle Secure to the top end of a Prior to installing the LED COB chip on board in the fixture verify that the LED COB corresponds with the fixture label Open the fixture by loosen 1 1 4 to 2 pipe by tightening set screws 5 16 18 NPT ing the six hex key screws on the door and rotate door to allow access to to 12 ft lbs and lock down with jam nuts 3 places 3 7 16 reflectors Unscrew the two hex key screws on either side of the reflector above the affected LED COB Remove reflector to allow access to LED COB Shielding Optio2. the catalog description listed on the packing slip with the fixture label on the inside of the housing to be sure you have received the correct merchandise This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Prior to Installation Read carefully before installing light fixtures If you do not understand these instructions please contact your local Litho nia Lighting distributor before installing Tools Required 9 64 and 3 16 hex key 1 4 and 5 16 hex socket regular screwdriver 1 Mounting Threaded Knuckle Mount THK DSXF1 and DSXF2 Knuckle 1 2 NPS threaded nipple or DSXF3 3 4 NPT threaded nipple mount di rectly to compatible NPTF apparatus Secure the knuckle to desired mounting apparatus by tightening the locknut not included To adjust the tilt angle of the fixture loosen the 3 16 hex key screw Adjust as necessary and retighten Supply leads exit the knuckle mount to make connections in wiring compartment not provided oooi DSXF1 1 2 knuckle DSXF2 1 2 knuckle DSXF3 3 4 knuckle Yoke Mount YK DSXF2 and DSXF3 only Mount the yoke to the desired bracketry by the center hole using a 3 4 bolt lock washer and nut not provided 1 2 inch bolts can be used in the two outer h
3. SAcuityBrands Lighting READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death personal injury or property damage from fire electric shock falling parts cuts abrasions and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels Before installing servicing or performing routine maintenance upon this equipment follow these general precautions Installation and service of luminaires should be performed by a qualified licensed electrician Maintenance of the luminaires should be performed by person s familiar with the luminaires construction and operation and any hazards involved Regular fixture maintenance programs are recommended It will occasionally be necessary to clean the outside of the refractor lens Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user Refractor lens should be washed in a solution of warm water and any mild non abrasive household detergent rinsed with clean water and wiped dry Should optical assembly become dirty on the inside wipe refractor lens and clean in above manner replacing damaged gaskets as necessary DO NOT INSTALL DAMAGED PRODUCT This luminaire has been properly packed so that no parts should have been damaged during transit Inspect to confirm Any part damaged or broken during or after asse
4. mbly should be replaced Recycle For information on how to recycle LED electronic products please visit www epa gov These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s or owner s purposes this matter should be referred to Acuity Brands Lighting Inc WARNING RISK OF ELECTRIC SHOCK WARNING RISK OF BURN Disconnect or turn off power before installation or Allowlamp fixture to cool before handling Do nottouch servicing Verify that supply voltage is correct by comparing it with the luminaire label information Make all electrical and grounded connections in accordance with the National Electrical Code NEC and any applicable local code requirements All wiring connections should be capped with UL approved recognized wire connectors CAUTION RISK OF INJURY Wear gloves and safety glasses at all times when removing luminaire from carton installing servicing or performing maintenance Avoid direct eye exposure to the light source while it is on enclosure or light source Do not exceed maximum wattage marked on luminaire label Follow all manufacturer s warnings recommendations and restrictions for driver type burning position mounting locations method
5. ns The doorframe can be opened with any of the clamp Remove the two LED COB clamp screws with a 1 cross recessed shielding options attached Attach with the 8 32 thread forming screws screwdriver Lift clamp noting positive pad orientation on COB remove provided Holes will be provided in the doorframe Should the door COB and replace with new oriented as old Attach the two clamp screws frame holes need be cleared for any reason drill no deeper than 1 2 torqued to 2 45 3 9 in lb 0 28 0 45N m Replace reflector and attach with with a 147 26 diameter drill two screws torqued to 2 5 in lb Check door gasket on housing for mis E iG alignment and correct as necessary Rotate the door assembly closed and n oi er FULL VISOR ena WIRE GUARD tighten the six hex key screws 50 in lbs EVENLY VISOR GUARD DSXF3 only Driver Access THE FIXTURE SHOULD NOT BE ENERGIZED DURING ANY ELECTRICAL WORK The driver is pre wired so access to the driver during installation is unnec i essary Open the fixture by loosening the six hex key screws on the door DSXF1 UV or BV DSXF1 VG and rotate the door away from housing to open Ensure the fixture is not energized and disconnect the electrical connectors to the affected driver Remove the two slotted hex screws holding the driver to the door Attach new driver with two slotted hex screws torqued to to 24 in lbs 2 7N m Reattach electrical connectors Check door gasket on housing for mis alignment and cor
6. oles if needed Tighten to 30 ft lbs To adjust the tilt angle of the fixture loosen the hex socket screw on each side of the yoke While holding weight of fixture remove hexhead set screw adjust as necessary and reinstall in appropriate matching hole If a non standard angle is desired adjust to angle and center punch inside yoke bracket and drill a 147in 26 hole Reinsert hexhead set screw Make the supply connections to the 16 3 cord supplied DSXF2 YOKE DSXF3 YOKE 0 13 thickness DSXF2 Yoke DSXF3 Yoke Lithonia Lighting Outdoor One Lithonia Way Conyers Georgia 30012 a LITHONIA LIGHTING Phone 800 279 8041 Fax 770 918 1209 wwwalithonia com Part Number RJ521350 Rev E AnsSAcuityBrands Company 2011 Acuity Brands Lighting Inc All rights reserved Revision Date 4 3 14 Installation Instructions DSXF LED Integral Slipfitter Mount IS DSXF1 or DSXF2 ships in fixture carton Remove parts from carton 1 fixture 1 slipfitter 1 hardware bag with quantity 1 gasket and 4 screws Place the gasket onto fixture bottom Place slipfitter against gasket and attach with 4 screws To adjust the tilt angle of the fixture loosen the 3 16 hex key screw Adjust as necessary and retighten Supply leads exit through the center of the slipfitter to make connections in wiring compartment not provided Secure to the top end of a 1 1 4 to 2 pipe by tightening set screws to 12 ft lbs DSXF3 ships installed Remove
7. rect as necessary Rotate the door assembly closed and tighten the six hex key screws 50 in lbs EVENLY DSXF2 UV or BV Troubleshooting If this fixture fails to operate properly check to make sure The fixture is wired correctly The fixture is grounded correctly e The line voltage at the fixture is correct If all these variables have been checked and the fixture still does not operate as specified contact your local Lithonia Lighting distributor DSXF3 UV or BV p DSXF3 VG DSXF3 WG Lithonia Lighting Outdoor One Lithonia Way Conyers Georgia 30012 CA LITHONIA LIGHTING Phone R e Pag Kan 209 www lithonia com Part Number RJ521350 Rev E An AcuityBrands Company 2012 Acuity Brands Lighting Inc All rights reserved Rev 3 13 Revision Date 4 3 14
8. s replacementand recycling CAUTION RISK OF FIRE Keep combustible and other materials that can burn away from lamp lens Donot operate in close proximity to persons combustible materials or substances affected by heat or drying A cuityBrands A CAUTION RISK OF PRODUCT DAMAGE Never connect components under load Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation Unless individual product specifications deem otherwise Never connect an LED product directly to a dimmer packs occupancy sensors timing devices or other related control devices LED fixtures must be powered directly off a switched circuit Unless individual product specifications deem otherwise Do not restrict fixture ventilation Allow for some volume of airspace around fixture Avoid covering LED fixtures with insulation foam or other material that will prevent convection or conduction cooling Unless individual product specifications deem otherwise Do not exceed fixtures maximum ambient temperature Only use fixture in its intended location LED products are Polarity Sensitive Ensure proper Polarity before installation Electrostatic Discharge ESD ESD can damage LED fixtures Personal grounding equipment must be worn during all installation or servicing of the unit Do not touch individual electrical components as this can cause ESD shorten lamp life or alter performance Some components inside
9. the fixture may not be serviceable In the unlikely event your unit may require service stop using the unit immediately and contact an ABL representative for assistance Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings LED IMPORTANT SAFETY INSTRUCTIONS Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory statements Failure to follow any of these instructions could void product warranties For a complete listing of product Terms and Conditions please visit www acuitybrands com Our Brands Indoor Outdoor Indoor Lighting Outdoor Lighting Controls Daylighting Lithonia Lighting Gotham American Electric Lighting DARK TO LIGHT SunOptics Carandini Mark Architectural Lighting Antique Street Lamps LC amp D Holophane Peerless Hydrel ROAM RELOC Renaissance Lighting Tersen Sensor Switch Light Concepts Winona Lighting Synergy Acuity Brands Lighting Inc assumes no responsibility for claims arising out of improper or careless installation or handling of its products ABL LED General Warnings Form No 503 203 2010 Acuity Brands Lighting Inc All rights reserved 12 01 10 Installation Instructions DSXF LED 5 year limited warranty DELIVERY Upon receipt of fixture and accessories packed separately thoroughly inspect for any freight damage All damage should be re ported to the delivery carrier Compare
Download Pdf Manuals
Related Search