Sea Gull Lighting 75520-845 Installation Guide
Contents
1. H to canopy so that center pipe G protrudes through hole in diffuser H Secure in place by threading washer and hex nut Y and finial L to center pipe G CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts2. INSTALLATION AND SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS NOTE FOR FIXTURES PROVIDED WITH 75 C OR 90 C SUPPLY WIRE WARNING ONLY THESE WARNINGS ARE PROVIDED ON THE LABEL AND ON THE FIXTURE e Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off e Use of other manufacturers components will void warranty listing CARTON RISK OF FIRE MOST DWELLINGS BUILT BEFORE and create a potential safety hazard 1985 HAVE SUPPLY WIRE RATED 60 C CONSULT A e If you are unclear as to how to proceed contact a qualified QUALIFIED ELECTRICIAN BEFORE INSTALLING electrician e You don t need special tools to install this fixture e Be sure to follow the steps in the order given e Read instructions carefully e Save these instructions GROUNDING AND MOUNTING BAR LOCK UP x OUTLET BOX OUTLET BOX lt MOUNTING RE CONNECTORS MOUNTING SCREWS I gt A MOUNTING WIRE BAR A CONNECTORS MOUNTING SCREWS I D lt OUTLET BOX GROUNDING SCREWS FIGURE 2 SCREW D NOT INCLUDED ANOPY E KEYSLOTS N HEX NUT Z _ CENTER PIPE G Cla gull lighbing Installation And Satety Instructions lt DIFFUSER H H C 1 1 55 070307 caD lt WASHER amp HEX NUT Y File This Sheet For Future Reference ITEM m FINIAL L Line art shown may not exactly match the fixture enclosed NO
3. T SUPPLIED However the installation instructions do apply to this fixture FIGURE 1 ASSEMBLY HC 1155 Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture STEP 1 Thread hex nut Z onto center pipe G Thread this end of center pipe into coupling M and secure with hex nut Z INSTALLATION IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Raised side is top as illustrated STEP 2 Thread fixture mounting screws I into threaded holes of mounting bar A 3 turns each STEP 3 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED a NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box Do Not twist wire
4. s together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A If uninsulated ground wire is on the mounting bar connect the ground wire from the fixture if Supplied and the outlet box to it using a small wire connector not supplied See Figure 2 NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box Raise the canopy E to the ceiling allowing for mounting screws l to protrude through key slots N Rotate canopy E clockwise until screws l are in narrow part of keyslot N Tighten screws I with screwdriver STEP 2 Install lamps STEP 3 Raise diffuser
Download Pdf Manuals
Related Search