Sea Gull Lighting 77225-02 Installation Guide
Contents
1. Installation And Safety Instructions Sea Gull Lightin Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM IMPORTANT SAFETY INSTRUCTIONS e Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off e Use of other manufacturers components will void warranty listing and create a potential safety hazard e To reduce the risk of fire electric shock or personal injury mount to outlet box or supporting system able to support the weight of the fixture e If you are unclear as to how to proceed contact a qualified electrician e You don t need special tools to install this fixture e Be sure to follow the steps in the order given e Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system e Read instructions carefully e Save these instructions CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be s2. e the screw collar ring G and canopy H in that order over chain S Open one link on the other end of the chain S and attach it to the screw collar E which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY FOR FLUSH MOUNT STEP 1 Thread mounting screws K into offset mounting bar N Run mounting screws K all the way down to their heads Secure offset mounting bar N to the outlet box raised side to top as illustrated using outlet box screws not supplied STEP 2 Remove fixture loop I from fixture Feed fixture wires through center of flush canopy Secure flush canopy to fixture by installing lock washer and nut over center nipple A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below i 4 GROUP A GROUP B CONNECT TO BLACK HOUSE WIRE CONNECT TO WHITE HOUSE WIRE PARALLEL WIRE SQUARE amp RIDGED Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the con
3. nector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 2 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire F from the fixture and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire F from the fixture and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 CHAIN HUNG ONLY Make sure no bare wires can be seen outside wire connectors After wires are connected tuck them carefully inside outlet box Push the fixture firmly over the mounting screws F and against the wall Secure canopy I in place with cap nuts E STEP 2 FLUSH MOUNT ONLY Place flush canopy to ceiling so mounting screws K protrude through flush canopy and secure by threading cap nuts to mounting K Install lamps n fe Q o D STEP 4 Raise diffuser O over b
4. ottom nipple P and secure by threading finial L to bottom nipple P
5. ure to use exact wording from illustration when ordering parts BEFORE YOU BEGIN Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 Be careful not to misplace any of the screws or parts which are needed to install this fixture Thread fixture loop I to fixture if applicable HC 1323 100908 GROUNDING AND MOUNTING BAR LOCK UP FLUSH MOUNT GREEN GROUNDING E SCREW D OUTLET BOX SCREWS gt FIGURE 2 WIRE CONNECTORS NUT B NIPPLE C CANOPY H BOTTOM NIPPLE P lt OUTLET BOX GROUND WIRE WIRE CONNECTORS OFFSET 4 FINIAL gt S7 FIGURE 1 MOUNTING A a BAR N MOUNTING SCREWS K NOT INCLUDED OUTLET BOX GROUND WIRE lt MOUNTING BAR A QUTLET BOX SCREWS SCREW COLLAR E LOOP I O DIFFUSER 0 NOT SUPPLIED INSTALLATION HC 1323 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX FOR CHAIN HUNG STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 5 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Thread screw collar E to nipple C STEP 2 Using 2 pairs of pliers open one link of chain S and connect it to the fixture loop I at the top of the fixture STEP 3 Slid
Download Pdf Manuals
Related Search