Sea Gull Lighting 5232-02 Installation Guide
Contents
1. Installation And Safety Instructions HC 264 Saq Gull Lighting Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to i this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM __ 081409 FOR CHAIN HUNG Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off Use of other manufacturers components will void warranty listing and create a potential safety hazard If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given WIRE Under no circumstances should a fixture be hung on house S S CONNECTORS electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Ee ey W4_____ Read instructions carefully y T l L MOUNTING Save these instructions ji i SCREWS I NUT B CANOPY LOOP E O a O CAP NUTS F a OUTLET BOX CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure2. KWASHER Q gt lt 77 Nut B lt 7 CANOPY G CAP NUTS F gt o O lt TOP OF COUPLING M FF NY FIXTURE K FIGURE 3
3. PORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Thread fixture mounting screws I in through top of mounting bar A raised side is on top as illustrated Run screw threads all the way down to the heads Secure mounting bar A to outlet box with outlet box screws not supplied For flush mount proceed to step 4 STEP 2 A Use a listed wire connector to connect the fixture hot wire black wire or round and smooth tracer to the supply hot wire B Use a listed wire connector to connect the fixture common wire white wire or Square and rigid to the supply common wire C Gently try to remove the wires from the connector If you can remove the wires carefully re do the wiring connection STEP 3 GROUNDING INSTRUCTIONS Connect the supply ground wire fixture ground wire and mounting bar ground wire pre attached using the supplied wiring connector Gently try to remove the wires from the connector If you can remove the wires carefully re do the wiring connection FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 4 After wires are connected tuck them carefully inside outlet box and then raise the canopy G against ceiling allowing for mounting crews l to protrude through holes in canopy G Secure in place F o a gt O Q O Cc F op STEP 5 Install candle covers T if applicable STEP 6 Install lamps FOR FLUSH MOUNT LOC
4. to use exact wording from illustration when FIXTURE LOOP J CHAIN N REPLACING GLASS COUPLING M d O e 3 a 5 5 Co ze i mi O 5 Q 5 Q ts ol oO e 5 h SJ n 7 F O O 0 CENTER soca replaced Install glass up through bottom of fixture Bend tabs back PIPE P HH as before FIXTURE n o CAGE 0 BEFORE YOU BEGIN aiin J mo TT l O 0 O O 09 Q Q 0p no 0 Cc O O 0 Q O 0 Q 07 QO O 9 0 O Q CANDLE Carefully remove the fixture from the carton and check that all parts COVER T I are included as shown in Figure 1 Be careful not to misplace any of L the screws or parts which are needed to install this fixture Os 354 FIGURE 1 ali NOT SUPPLIED FOR CHAIN HUNG FIG 1 AND Install canopy loop E on canopy G with lockwasher Q and nut B MOUNTING Note Loop may be factory installed BAR LOCK UP STEP 1 AND STEP 2 GROUND Install lock washer Q nipple C and fixture loop J in that order on WIRE coupling M CONNECTORS STEP 2 FOR FLUSH MOUNT IF APPLICABLE FIG 3 MOUNTING Install nipple C onto coupling M if applicable BAR A MOUNTING v OUTLET STEP 3 SCREWS I A Insert fixture assembly through canopy G Secure in place with lock FIGURE 2 GREEN GROUNDING SCREW D NOT INCLUDED washer Q and nut B INSTALLATION HC 264 IM
Download Pdf Manuals
Related Search