Home Decorators Collection YG486-NI Instructions / Assembly
Contents
1. If using the ceiling light kit make sure the screws securing the glassware are tight Check that the light bulbs are also secure Make sure there is a short distance from the ceiling to the canopy It should not touch the ceiling Make sure your ceiling box is secure and that rubber isolator pads are used between the mounting bracket and outlet box 19 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Troubleshooting continued Problem The fan wobbles Solution Verify that all blades and blade bracket screws are secure most fan wobble problems are caused by loose parts Once the fan is properly installed run the ceiling fan for 10 minutes to let the fan self adjust If wobble occurs after running the fan for 10 minutes verify blade level using the following process Select a point on the ceiling above the tip of one of the blades then select any fan blade and measure from the center of the selected blade to the point on the ceiling Rotate the fan until the next blade is positioned and repeat the measurement using the same point from the ceiling for every blade Measurement deviations should be within 1 8 in Ifall deviations are less than 1 8 in and the fan continues to wobble please call Customer Service 1 800 986 3460 to order a complimentary Blade Balancing Kit f deviation is greater than 1 8 in pleas2. essses 9 Close to Ceiling Mounting eren 10 Hanging the FAM succurrere revera evoca 11 Attaching the Fan Blades sees 14 Installing the Light KI 16 Operation p 18 Pull Chain Operating Instructions 18 Reverse Switch Operating Instructions 18 Care and Cleaning 19 Troubleshooting eereeeeeeeeeeeeee 19 Service 21 Safety Information 1 To reduce the risk of electric shock ensure electricity has been turned off at the circuit breaker or fuse box before beginning not use this fan with any solid state fan speed control device j WARNING To reduce the risk of electrical shock or fire do It will permanently damage the electronic circuitry 2 All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 1999 and local electrical codes Electrical installation should be performed by a qualified WARNING Do not insert foreign objects between rotating licensed electrician fan blades 3 Theoutlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 WARNING To reduce the
3. WARNING The locking slots of the canopy C are provided bracket A only as an aid to mounting Do not leave the fan assembly unattended until all four canopy mounting bracket screws Secure the canopy C to the mounting bracket A BB are engaged and firmly tightened with the four mounting bracket screws with lock washers BB provided Slide the canopy C up to the ceiling Make sure you have placed the wires safely into the outlet box QQ Slide the canopy ring B over the canopy and tighten by turning the ring B Secure the canopy C to the mounting bracket A with the four canopy mounting bracket screws and lock washers BB included with your fan Slide the canopy ring B over the canopy C and tighten by turning the ring B 13 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Attaching the Fan Blades 8 Removing the rubber packing mounts The fan motor assembly G is shipped with rubber packing mounts UU to prevent movement during transportation Remove the five rubber packing mounts UU from the fan motor assembly G and discard prior to attaching the blade arms I 9 Attaching the blades to the blade arms WARNING Failure to properly seat the blades H on the H blade arms 1 and engage in the spring locking mechanism WA XX could result in the fan
4. do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you The retailer shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law Some states do not allow the exclusion of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all prior warranties Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer Contact the Customer Service Team at 1 800 986 3460 or visit www HOMEDEPOT COM HOMEDECORATORS Pre Installation SPECIFICATIONS Fan size Speed Volts Amps Watts RPM CFM N W G W C F n Ew 0 23 10 65 1759 10 8 kgs 11 92 kgs Medium 0 36 26 111 3159 23 76 Ibs 26 22 Ibs 92 TL High 0 58 69 185 5288 LISTED TOOLS REQUIRED Phillips Flat blade Step Wire Electrical screwdriver screwdriver ladder stripper tape Pre Installation continued HARDWARE INCLUDED NOTE Hardware shown to actual size unless noted otherwise in the table below Fog P wut LL PP MM ZR cam Part Description Quantity AA Plastic wire nut not to scale 3 BB
5. risk of fire electric shock or Ibs Use only UL listed outlet boxes marked FOR FAN personal injury mount the fan to the outlet box marked SUPPORT acceptable for fan support with the screws provided with the outlet box 4 The fan must be mounted with a minimum of 7 ft clearance from the trailing edge of the blades to the floor CAUTION To reduce the risk of personal injury use only 5 Avoid placing objects in the path of the blades A the screws provided with the outlet box 6 To avoid personal injury or damage to the fan and other items be cautious when working around or cleaning the fan 7 Do not use water or detergents when cleaning the fan or fan blades A dry dust cloth or lightly dampened cloth will be suitable for most cleaning 8 After making electrical connections spliced conductors should be turned upward and pushed carefully up into the outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box 9 Allsetscrews must be checked and retightened where necessary before installation 3 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Warranty We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by
6. Canopy mounting bracket screw with lock washer preassembled 4 CC Clevis pin preassembled 1 DD Cotter pin preassembled 1 EE Setscrew preassembled 1 1 2 6 FF Cross pin preassembled GG Collar setscrew preassembled HH Collar mounting screw with lock washer preassembled ll Blade arm screw with lock washer preassembled 10 JJ Switch housing mounting screw preassembled 3 KK Light kit mounting screw preassembled 3 LL Plastic nut preassembled 1 MM Glass cap preassembled 1 1 2 2 NN Decorative nut preassembled 00 13 watt compact fluorescent bulb not to scale PP Pull chain and fob not to scale 5 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Pre Installation continued PACKAGE CONTENTS A B C D E F G J K L Part Description Quantity Part Description Quantity A Mounting bracket preassembled 1 G Fan motor assembly 1 B Canopy ring preassembled 1 H Blade 5 C Canopy 1 l Blade arm 5 D Canopy bottom cover preassembled 1 J Switch housing 1 E Hanger ball downrod assembly 1 K Light kit 1 F Coupling cover 1 L Glass shade 1 Pre Installation continued DUAL MOUNTING INSTRUCTIONS This ceiling fan is supplied with two types of hanging assemblies the standard ceilin
7. HOME Item 1001029008 DECORATORS Model YG486 NI COLLECTION USE AND CARE GUIDE OCONEE 52 IN CEILING FAN Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 6 p m EST Monday Friday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS THANK YOU We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this ceiling fan We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Home Decorators Collection Table of Contents Table of Contents cccssssccsssesesssseenssnsecnseeennsseeennsnsenaae 2 Safety Information ecce 3 Ela 4 Pre Installation 2 5 eiii aa enun E aiana 4 SpeCcifICaliOliS ccce vides ierit teg ehe ugar ern ces 4 70015 Required P 4 Hardware 2 errore reuera 5 Package POTE 6 Dual Mounting Instructions eene 7 Installation 12s oai nuni an aucun a x anas ra rna 8 Assembly nnne tne nh nein en aaan kaana 9 Standard Ceiling Mounting
8. OMEDEPOT COM HOMEDECORATORS Retain this manual for future use YG486NI0001A
9. blades H loosening and possibly A falling To install the blade to the blade arm Hold the blade H with hands close to the blade arm I align the key slot holes VV with the blade arm posts WW and press the blade down firmly Ensure the key slot holes VV are properly seated on the blade arm posts WW until the blade H engages in the spring locking mechanism XX Make sure the spring of the spring locking mechanism XX is upward and the butt of the spring locking mechanism XX is against the edge of the blade To detach the blade from the blade arm Firmly slide the blade away from the blade arm I Press down the spring locking mechanism XX to release the blade H from the blade arm I Slide the blade H toward the blade arm 1 until the blade disengages from the spring locking mechanism XX and carefully push the blade H up to detach from the blade arm l 14 Assembly Attaching the Fan Blades 1 Fastening the blade assemblies to the motor WARNING To reduce the risk of personal injury do not bend the blade arms I while installing balancing the blades H or cleaning the fan Do no insert foreign objects between rotating fan blades H Fasten the blade assemblies to the fan motor assembly G by lining up the slots YY of the moto
10. c shock or other personal injury mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box Da Pass the 120 volt supply wires through the center hole in the mounting bracket A Attach the mounting bracket A on the outlet box QQ by sliding the mounting bracket A over the screws provided with the outlet box When using close to ceiling mounting it is important that the mounting bracket A be level If necessary use leveling washers not included between the mount ing bracket A and the outlet box QQ Note that the flat side of the mounting bracket A is toward the outlet box QQ Securely tighten the two mounting screws Hanging instructions for standard mounting QQ 5 Hanging instructions for close to ceiling mounting A WARNING The tab in the ring must rest in the groove of the hanger ball E Failure to properly seat the tab in the groove could cause damage to the wiring Carefully lift the fan motor assembly G up to the mounting bracket A and seat the hanger ball E in the mounting bracket A socket Make sure the tab on the mounting bracket A socket is properly seated in the groove in the hanger ball E This will help to balance the ceiling fan WARNING The hook is only to hold the fan while attaching wiring Failure to hang as instr
11. canopy C and loosen the slotted mounting bracket screws BB on the canopy C Take out the setscrew EE located in the hanger ball SS lower the hanger ball and remove the cross pin FF Remove the hanger ball SS from the the hanger ball downrod assembly E Remove the canopy C from the mounting bracket A by turning the canopy C counterclockwise FF iss SS EE o 3 Assembling the fan WARNING Failure to properly install the cotter pin DD could result in the fan loosening and possibly falling NOTE If a longer downrod not included is needed take out the screw located in the hanger ball SS lower the hanger ball SS and remove the pin FF Remove all three pieces from the downrod and assemble them onto the new longer downrod before proceeding to the downrod installa tion Carefully feed the motor wires up through the downrod TT Thread the downrod TT into the collar Align the holes and replace the cotter pin DD and clevis pin CC Tighten the two collar setscrews GG Slip the coupling cover F canopy ring B and canopy C onto the downrod TT Carefully reinstall the hanger ball SS onto the downrod TT being sure that the cross pin FF is in the correct position the setscrew EE is tightened and the wires are not twisted 9 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further a
12. e call Customer Service 1 800 986 3460 to order complimentary replacements of your brackets 20 Service Parts Part Description Mounting bracket preassembled Canopy ring preassembled Canopy Canopy bottom cover preassembled Hanger ball downrod assembly Coupling cover Fan motor assembly Blade Blade arm Switch housing Light kit 9 Glass shade ww 21 BB PP GG 5 00 HH Description Plastic wire nut Canopy mounting bracket screw with lock washer preassembled Clevis pin preassembled Cotter pin preassembled Setscrew preassembled Cross pin preassembled Collar setscrew preassembled Collar mounting screw with lock washer preassembled Blade arm screw with lock washer preassembled Switch housing mounting screw preassembled Light kit mounting screw preassembled Plastic nut preassembled Glass cap preassembled Decorative nut preassembled 13 watt compact fluorescent bulb Pull chain and fob HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance HOME DECORATORS COLLECTION Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 6 p m EST Monday Friday 1 800 986 3460 H
13. e when installing on a steep sloped ceiling The maximum angle allowable is 18 away from horizontal If the canopy C touches the hanger ball downrod assembly E then remove the decorative canopy bottom cover D and turn the canopy C 180 before attaching the canopy C to the mounting bracket A If your ceiling fan does not have an existing UL listed mounting box then install one using the following instructions Disconnect the power by removing the fuses or turning off the circuit breakers Secure the outlet box QQ not included directly to the building structure Use appropriate fasteners and materials not included The outlet box and its bracing must be able to fully support the weight of the moving fan at least 35 Ibs Do not use a plastic outlet box The illustrations below show three different ways to mount the outlet box QQ not included QQ RR a bs QQ To hang your fan where there is an existing fixture but no ceiling joist you may need an installation hanger bar RR not included as shown above Assembly Standard Ceiling Mounting 1 Preparing the canopy 2 Preparing the motor Remove the canopy ring B from the canopy C Remove the clevis pin CC and cotter pin DD and loosen the two collar setscrews GG from the motor Remove the two non slotted mounting bracket screws collar BB from the
14. g installation using the downrod with ball and socket mounting and the close to ceiling mounting The close to ceiling mounting is recommended in rooms with less than 8 ft ceilings or in areas where additional space is desired from the floor to the fan blades When using the standard downrod installation the distance from the ceiling to the bottom of the fan blades will be approximately 12 in The close to ceiling installation reduces the distance from the ceiling to the bottom of the fan blades to approximately 9 in Once you have decided which ceiling installation you will use refer to the corresponding sections and procedures during the assembly period Where necessary each section of the instructions will note the different procedures to follow for the two types of installation Standard Ceiling Mounting Close to Ceiling Mounting HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Installation MOUNTING OPTIONS WARNING To reduce the risk of fire electric shock or personal injury mount the fan to an outlet box marked acceptable for fan support using the screws provided with the outlet box An outlet box commonly used for the support of lighting fixtures may not be acceptable for fan support and may need to be replaced If in doubt consult a qualified electrician NOTE You may need a longer downrod to maintain proper blade clearanc
15. ke sure they are secure or the wood or possibly cause an electrical shock Because of the fan s natural movement some connections may become loose over time It is not Apply oil to your fan or motor The motor has necessary to remove the fan from the ceiling permanently lubricated sealed ball bearings Clean your fan periodically Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or Optional Apply a light coat of furniture polish to the wood Optional Cover small scratches with a light application of Troubleshooting panel box before you attempt any repairs Refer to the section WARNING Make sure the power is off at the electrical Making the Electrical Connections on page 12 Problem Solution The fan will not start Check the main and branch circuit fuses or breakers Check the line wire connections to the fan and switch wire connections in the switch housing The fan sounds noisy Make sure all motor housing screws are snug Make sure the screws that attach the fan blade arm to the motor hub are tight Make sure the wire nut connections are not rattling against each other or the interior wall of the switch housing Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this time
16. peration PULL CHAIN OPERATING INSTRUCTIONS Install two pull chains and fobs PP onto the pull chains located in the switch housing J Turn on the power and check the operation of the fan The pull chain controls the fan speed as follows 1 pull High 2 pulls Medium 3 pulls Low and 4 pulls Off Speed settings for warm or cool weather depend on factors such as the room size ceiling height and number of fans The light pull chain controls the light kit ON and OFF REVERSE SWITCH OPERATING INSTRUCTIONS The reverse switch is located on the surface of the switch housing Slide the switch to the left for warm weather operation Slide the switch to the right for cool weather operation NOTE Wait for the fan to stop before reversing the direction of the blade rotation Warm weather Counterclockwise Direction A downward air flow creates a cooling effect This allows you to set your air conditioner on a warmer setting without affecting your comfort Cool weather Clockwise Direction An upward air flow moves warm air off the ceiling This allows you to set your heating unit on a cooler setting without affecting your comfort 18 Care and Cleaning tarnishing blades shoe polish Do Do not Check the support connections brackets and blade Use water when cleaning Water could damage the motor attachments twice a year Ma
17. r G with the tabs ZZ on the blade arms l Tighten the two blade arm screws with lock washers Il already installed in the blade arms I Repeat this procedure for the remaining blade arms Ij 15 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Installing the Light Kit 1 Attaching the switch housing to the mounting ring CAUTION Before starting installation disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box Turning power off using the fan switch is not sufficient to prevent electric shock Remove one of the three switch housing mounting screws JJ from the mounting ring AAA and loosen the other two screws JJ Do not remove While holding the switch housing J under the fan motor assembly G snap together the wire connec tion plugs BBB Place the key holes in the switch housing J over the two screws JJ previously loosened from the mounting ring AAA Turn the switch housing J until the switch housing J locks in place at the narrow section of the key holes Secure by tightening the two mounting screws JJ previously loosened and the one JJ previously removed 4 16 Attaching the light kit to the switch housing Remove one of the three light kit mounting screws KK from the switch ho
18. ssistance Assembly Close to Ceiling Mounting 1 3 Preparing the canopy Remove the canopy ring B from the canopy C Remove the mounting bracket A from the canopy C by loosening the four canopy mounting bracket screws BB on the top of the canopy C Remove the two non slotted canopy mounting bracket screws BB and loosen the slotted canopy mounting bracket screws BB Remove the canopy bottom cover D from the canopy C Assembling the fan AN WARNING Failure to completely tighten the three collar mounting screws HH could result in the fan becoming loose and possibly falling Make sure the slot openings of the canopy ring B are on top and then proceed to place the canopy ring B and canopy C over the collar at the top of the fan motor assembly G Align the mounting holes in the bottom of the canopy C with the holes in the top of the fan motor assem bly G Fasten using the three collar mounting screws with lock washers HH previously removed Tighten the collar mounting screws HH securely Preparing the motor Remove three of the six collar mounting screws with lock washers HH every other one from the collar on top of the fan motor assembly G Assembly Hanging the Fan AN Attaching the fan to the electrical box WARNING To reduce the risk of fire electri
19. the original purchaser We also warrant that all other fan parts excluding any glass or acrylic blades to be free from defects in workmanship and material at the time of shipment from the factory for a period of two years after the date of purchase by the original purchaser We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned To obtain warranty service you must present a copy of the receipt as proof of purchase All costs of removing and reinstalling the product are your responsibility Damage to any part such as by accident misuse improper installa tion or by affixing any accessories is not covered by this warranty Because of varying climatic conditions this warranty does not cover any changes in brass finish including rusting pitting corroding tarnishing or peeling Brass finishes of this type give their longest useful life when protected from varying weather conditions A certain amount of wobble is normal and should not be considered a defect Servicing performed by unauthorized persons shall render the warranty invalid There is no other express warranty We hereby disclaim any and all warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty Some states
20. ucted may result in the tab breaking causing the fan to fall The hook must pass from the inside to the outside of the canopy Carefully lift the fan motor assembly G up to the mounting bracket A and hang the fan on the hook provided using one of the holes at the outer rim of the canopy 11 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Hanging the Fan continued Making the electrical connections Ground WARNING To avoid possible electrical shock be sure Black White conductor electricity is turned off at the main fuse box before wiring including ground and that no bare wire is visible at the wire WARNING Check to see that all connections are tight nuts except for the ground wire WARNING To reduce the risk of fire or electric shock do AR LN 2 e S A ee not use this fan with any solid state speed control device If you feel you do not have enough electrical wiring knowledge or experience have your fan installed by a licensed electrician o 2 g 6 c o m 6 Follow the steps below to connect the fan to your household wiring Use the plastic wire nuts AA with your fan Secure the plastic wire nuts AA with electrical tape Make sure there are no loose strands or connections Connect the ground conductor of the 120V supply this may be a bare wire or a wire with green colored ins
21. ulation to the green ground lead s of the fan When using standard ceiling mounting there are two green grounding leads one from the mounting bracket A and one from the hanger ball downrod assembly E When using close to ceiling mounting there is only one green ground lead from the mounting bracket A since the hanger ball downrod assembly E is not used o Connect the fan motor white wire to the supply white neutral wire using a plastic wire nut AA Connect the fan motor black wire and the blue wire to the supply black hot wire using a plastic wire nut AA Turn the wire nut connections upward spreading them apart so the green ground will be on one side of the outlet box QQ and the white black and blue wire will be on the other side Carefully tuck the connections up into the outlet box QQ 12 Assembly Hanging the Fan continued 7 Standard ceiling mounting 7b Close to ceiling mounting WARNING Make sure the tab on the mounting bracket A WARNING Locking slots of the canopy C are provided properly sits in the groove in the hanger ball E before only as an aid to mounting Do not leave the fan assembly attaching the canopy C to the mounting bracket A by unattended until all four canopy screws BB are engaged and turning the canopy C until it drops into place firmly tightened Remove the fan from the hook on the mounting
22. using J and loosen the other two screws KK Do not remove While holding the light kit K under the fan motor assembly G snap together the two wire plugs CCC White to white Black to blue Place the key holes in the light kit K over the two screws KK previously loosened from the switch housing J Turn the light kit K until the light kit K locks in place at the narrow section of the key holes Secure by tightening the two light kit mounting screws KK previously loosened and the one KK previously removed Assembly Installing the Light Kit continued 1 3 Installing the light bulbs and glass shade CAUTION Before starting installation disconnect the CC power by turning off the circuit breaker or removing the fuse at the fuse box Turning power off using the fan switch is not S N G sufficient to prevent electric shock Remove the decorative nut NN glass cap MM and D plastic nut LL from the light kit K Z Install two 13 watt compact fluorescent bulbs 00 included Place the glass shade L over the light kit K stem and secure with the plastic nut LL rubber side on the top Do not overtighten Secure the glass cap MM and decorative nut NN previously removed Do not overtighten L T 5 Mii O 17 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance O
Download Pdf Manuals
Related Search