Home Decorators Collection AC303-NI+MHHDC Instructions / Assembly
Contents
1. AA B EE E JJ Pos EH BB i LL B GG COS MM DD II 8 OO Part Description Quantity AA Plastic wire nut not to scale 3 BB Canopy mounting bracket screw with lock washer preassembled 4 CC Clevis pin preassembled 1 DD Cotter pin preassembled 1 EE Setscrew preassembled 1 FF Cross pin preassembled 1 GG Collar setscrew preassembled 2 HH Collar mounting screw with lock washer preassembled 6 ll Blade arm screw with lock washer preassembled 10 JJ Switch housing mounting screw preassembled 3 KK Light kit mounting screw preassembled 3 LL 13 watt compact fluorescent bulb not to scale 2 Pull chain and fob not to scale 2 NN Rubber gasket not to scale 1 00 Plastic plug not to scale 1 5 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Pre Installation continued PACKAGE CONTENTS A B C D E F G J K L Part Description Quantity Part Description Quantity A Mounting bracket preassembled 1 G Fan motor assembly 1 B Canopy ring preassembled 1 H Blade 5 C Canopy 1 l Blade arm 5 D Canopy bottom cover preassembled 1 J Switch housing 1 E Hanger ball downrod assembly 1 K Light kit 1 F Coupling cover 1 L Glass shade 1 Pre Installation continued DUAL MOU2. Attaching the light kit to the switch housing Remove the three light kit mounting screws KK from the light kit K and keep these screws While holding the light kit K under your fan motor assembly G locate two single white and blue wires in the switch housing labeled FOR LIGHT Make the polarized plug connections III White to white Blue to black Carefully push all wires back into the switch housing Install the light kit K onto the switch housing with the three light kit mounting screws KK provided Be sure to tighten all screws Assembly Installing the Light Kit continued 1 3 Installing the light bulb and glass shade CAUTION Before starting installation disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box Turning power off using the fan switch is not sufficient to prevent electric shock Install two 13 watt compact fluorescent bulbs LL included Raise the glass shade L up against the light kit K and secure the glass shade L to the fan by turning the glass shade L clockwise until snug Do not overtighten 1 4 Installing the fan without the light kit optional Disassemble the switch housing cover JJJ from the light kit K You can keep the light kit K for future use Attach the plastic plug 00 to the switch housing cover JJJ Install the switch housing cover J
3. 9 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Close to Ceiling Mounting 3 Preparing the canopy Remove the mounting bracket A from the canopy C by loosening the four canopy mounting bracket screws BB on the top of the canopy C Remove the two non slotted canopy mounting bracket screws BB and loosen the slotted canopy mounting bracket screws BB Remove the canopy bottom cover D from the canopy C Assembling the fan AN WARNING Failure to completely tighten the three collar mounting screws HH could result in the fan becoming loose and possibly falling Make sure the slot openings of the canopy ring B are on top and then proceed to place the rubber gasket NN canopy ring B and canopy C over the collar at the top of the fan motor assembly G Align the mounting holes in the bottom of the canopy C and the mounting holes in the rubber gasket with the holes in the top of the fan motor assembly G Fasten using the three collar mounting screws with lock washers HH previously removed Tighten the collar mounting screws HH securely 2 Preparing the motor Remove three of the six collar mounting screws with lock washers HH every other one from the collar on top of the fan motor assembly G Assembly Hanging the Fan
4. Attaching the fan to the electrical box WARNING To reduce the risk of fire electric shock or other personal injury mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box Da Pass the 120 volt supply wires through the center hole in the mounting bracket A Attach the mounting bracket A on the outlet box PP by sliding the mounting bracket A over the screws provided with the outlet box When using close to ceiling mounting it is important that the mounting bracket A be level If necessary use leveling washers not included between the mounting bracket A and the outlet box PP Note that the flat side of the mounting bracket A is toward the outlet box PP Securely tighten the two mounting screws Hanging instructions for standard mounting PP 5 Hanging instructions for close to ceiling mounting A WARNING The tab in the ring must rest in the groove of the hanger ball E Failure to properly seat the tab in the groove could cause damage to the wiring Carefully lift the fan motor assembly G up to the mounting bracket A and seat the hanger ball E in the mounting bracket A socket Make sure the tab on the mounting bracket A socket is properly seated in the groove in the hanger ball E This will help to balance the ceiling fan WA
5. 18 Care and Cleaning tarnishing blades shoe polish Do Do not Check the support connections brackets and blade Use water when cleaning Water could damage the motor attachments twice a year Make sure they are secure or the wood or possibly cause an electrical shock Because of the fan s natural movement some connections may become loose over time It is not Apply oil to your fan or motor The motor has necessary to remove the fan from the ceiling permanently lubricated sealed ball bearings Clean your fan periodically Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or Optional Apply a light coat of furniture polish to the wood Optional Cover small scratches with a light application of Troubleshooting panel box before you attempt any repairs Refer to the section WARNING sure the power is off at the electrical Making the Electrical Connections on page 12 Problem Solution The fan will not start Check the main and branch circuit fuses or breakers Check the line wire connections to the fan and switch wire connections in the switch housing The fan sounds noisy Make sure all motor housing screws are snug Make sure the screws that attach the fan blade
6. HOME Item 1000035582 DECORATORS Model AC303 NI MH COLLECTION USE AND CARE GUIDE TAHITI BREEZE 52 IN CEILING FAN b j QJ 226 7 ey SZ Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 6 p m EST Monday Friday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS THANK YOU We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this ceiling fan We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Home Decorators Collection Table of Contents Table of Contents nore ccsececccecsnnccannaaes 2 Safety Information ecce 3 leen EE 4 Pre Installation ritorno aea nucece 4 SpecifICallofis s cci es hogar cen ces 4 15 n 4 Hardware Included 5 Package Gontehts tution etes 6 Dual Mounting Instruction eren 7 INSTA ATION me 8 Assembly tenen nh nein en 9 Standard Ceili
7. JJ to the switch housing J with light kit mounting screws KK provided 17 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Operation PULL CHAIN OPERATING INSTRUCTIONS Install two pull chains and fobs MM onto the pull chains located in the switch housing J Turn on the power and check the operation of the fan The pull chain controls the fan speed as follows 1 pull High 2 pulls Medium 3 pulls Low and 4 pulls Off Speed settings for warm or cool weather depend on factors such as the room size ceiling height and number of fans SSS 2226 S UN 77 SE The light pull chain controls the light kit ON and OFF aX DVA Ae REVERSE SWITCH OPERATING INSTRUCTIONS Y The reverse switch is located on the surface of the switch housing CJ 7 This switch controls directions forward switch down or reverse switch up NOTE Wait for the fan to stop before reversing the direction of the blade rotation Warm weather Counterclockwise Direction A downward air flow creates a cooling effect This allows you to set your air conditioner on a warmer setting without affecting your comfort Cool weather Clockwise Direction An upward air flow moves warm air off the ceiling This allows you to set your heating unit on a cooler setting without affecting your comfort
8. MEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance HOME DECORATORS COLLECTION Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 6 p m EST Monday Friday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS Retain this manual for future use AC303NI MHO1A
9. NTING INSTRUCTIONS This ceiling fan is supplied with two types of hanging assemblies the standard ceiling installation using the downrod with ball and socket mounting and the close to ceiling mounting The close to ceiling mounting is recommended in rooms with less than 8 ft ceilings or in areas where additional space is desired from the floor to the fan blades When using the standard downrod installation the distance from the ceiling to the bottom of the fan blades will be approximately 12 in The close to ceiling installation reduces the distance from the ceiling to the bottom of the fan blades to approximately 9 in Once you have decided which ceiling installation you will use refer to the corresponding sections and procedures during the assembly period Where necessary each section of the instructions will note the different procedures to follow for the two types of installation Standard Ceiling Mounting Close to Ceiling Mounting HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Installation MOUNTING OPTIONS WARNING To reduce the risk of fire electric shock or personal injury mount the fan to an outlet box marked acceptable for fan support using the screws provided with the outlet box An outlet box commonly used for the support of lighting fixtures may not be acceptable for fan support and may need to be replaced If in doubt consult a
10. RNING The hook is only to hold the fan while attaching wiring Failure to hang as instructed may result in the tab breaking causing the fan to fall The hook must pass from the inside to the outside of the canopy Carefully lift the fan motor assembly G up to the mounting bracket A and hang the fan on the hook provided using one of the holes at the outer rim of the canopy 11 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Hanging the Fan continued Making the electrical connections WARNING To avoid possible electrical shock be sure TT UU VV electricity is turned off at the main fuse box before wiring WARNING Check to see that all connections are tight including ground and that no bare wire is visible at the wire nuts except for the ground wire 7 ON WARNING To reduce the risk of fire or electric shock do Q not use this fan with any solid state speed control device If you feel you do not have enough electrical wiring knowledge or experience have your fan installed by a licensed electrician Follow the steps below to connect the fan to your household wiring Use the plastic wire nuts AA with your fan Secure the plastic wire nuts AA with electrical tape Make sure there are no loose strands or connections Connect the ground conductor VV of the 120V supply this may
11. arm to the motor hub are tight Make sure wire nut connections are not rattling against each other or the interior wall of the switch housing Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this time If using the ceiling light kit check the light bulb is secure Make sure there is a short distance from the ceiling to the canopy It should not touch the ceiling Make sure your ceiling box is secure and rubber isolator pads are used between the mounting bracket and outlet box 19 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Troubleshooting continued Problem The fan wobbles Solution Verify that all blades and blade bracket screws are secure most fan wobble problems are caused by loose parts Once the fan is properly installed run the ceiling fan for 10 minutes to let the fan self adjust If wobble occurs after running the fan for 10 minutes verify blade level using the following process Select a point on the ceiling above the tip of one of the blades then select any fan blade and measure from the center of the selected blade to the point on the ceiling Rotate the fan until the next blade is positioned and repeat the measurement using the same point from the ceiling for every blade Measurement deviations should be within 1 8 Ifall deviations ar
12. be a bare wire or a wire with green colored insulation to the green ground lead s ZZ of the fan When using standard ceiling mounting there are two green grounding leads one from the mounting bracket A and one from the hanger ball downrod assembly E When using close to ceiling mounting there is only one green ground lead ZZ from the mounting bracket A since the hanger ball downrod assembly E is not used o Connect the fan motor white wire YY to the supply white neutral wire UU using a plastic wire nut AA Connect the fan motor black wire XX and the blue wire WW to the supply black hot wire TT using a plastic wire nut AA Turn the wire nut connections upward spreading them apart so the green ground ZZ will be on one side of the outlet box PP and the white YY black XX and blue wire WW will be on the other side Carefully tuck the connections up into the outlet box PP 12 Assembly Hanging the Fan continued 7 Standard ceiling mounting 7b Close to ceiling mounting WARNING Make sure the tab on the mounting bracket A WARNING Locking slots of the canopy C are provided properly sits in the groove in the hanger ball E before only as an aid to mounting Do not leave the fan assembly attaching the canopy C to the mounting bracket A by unattended until all four canopy screws BB are engaged and turning the canopy C until it dr
13. crews GG from the motor Remove the two non slotted mounting bracket screws collar BB from the canopy C and loosen the slotted mounting bracket screws BB on the canopy C Take out the setscrew EE located in the hanger ball RR lower the hanger ball and remove the cross pin FF Remove the hanger ball RR from the hanger ball downrod assembly E Remove the canopy C from the mounting bracket A by turning the canopy C counterclockwise RR 3 Assembling the fan WARNING Failure to properly install the cotter pin DD could result in the fan loosening and possibly falling NOTE If a longer downrod not included is needed take out the screw located in the hanger ball RR lower the m hanger ball RR and remove the pin FF Remove all three pieces from the downrod and assemble them onto the new longer downrod before proceeding to the downrod installa tion Carefully feed the motor wires up through the downrod SS Thread the downrod SS into the collar Align the holes and replace the cotter pin DD and clevis pin CC Tighten the two collar setscrews GG Slip the coupling cover F canopy ring B and canopy C onto the downrod SS Carefully reinstall the hanger ball RR onto the downrod SS being sure that the cross pin FF is in the correct position the setscrew EE is tightened and wires are not twisted
14. e less than 1 8 and the fan continues to wobble please call Customer Service 1 800 986 3460 to order a complimentary Blade Balancing Kit f deviation is greater than 1 8 in please call Customer Service 1 800 986 3460 to order complimentary replacements of your brackets 20 Service Parts Description Mounting bracket preassembled Canopy ring preassembled Canopy Canopy bottom cover preassembled Hanger ball downrod assembly Coupling cover Fan motor assembly Blade Blade arm Light kit mounting plate Light kit Glass shade Dm 21 B L cc ll L3 mil Ee EE GG MM BB HH JJ DD KK EE LL Part Description AA Plastic wire nut BB Canopy mounting bracket screw with lock washer preassembled Clevis pin preassembled Cotter pin preassembled Setscrew preassembled Cross pin preassembled Collar setscrew preassembled Collar mounting screw with lock washer preassembled Blade arm screw with lock washer preassembled JJ Light kit mounting plate screw preassembled KK Light kit mounting screw preassembled LL 13 watt compact fluorescent bulb MM Pull chain and fob NN Rubber gasket 00 Plastic plug HO
15. ed and capable of reliably supporting a minimum of 35 WARNING To reduce the risk of fire electric shock or Ibs Use only UL listed outlet boxes marked FOR FAN personal injury mount the fan to the outlet box marked SUPPORT acceptable for fan support with the screws provided with the outlet box 4 The fan must be mounted with a minimum of 7 ft clearance from the trailing edge of the blades to the floor CAUTION To reduce the risk of personal injury use only 5 Avoid placing objects in the path of the blades A the screws provided with the outlet box 6 To avoid personal injury or damage to the fan and other items be cautious when working around or cleaning the fan 7 Do not use water or detergents when cleaning the fan or fan blades A dry dust cloth or lightly dampened cloth will be suitable for most cleaning 8 After making electrical connections spliced conductors should be turned upward and pushed carefully up into the outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box 9 Allsetscrews must be checked and retightened where necessary before installation 3 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Warranty We warrant the fan motor to be free from defects in workmanship and material present at time of shipme
16. imited to the time period as specified in the express warranty Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you The retailer shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law Some states do not allow the exclusion of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all prior warranties Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer Contact the Customer Service Team at 1 800 986 3460 or visit www HOMEDEPOT COM HOMEDECORATORS Pre Installation SPECIFICATIONS Fan size Speed Volts Amps Watts RPM CFM N W G W C F n Ew 0 24 10 89 63 1620 89 11 87 kgs 12 83 kgs M 7 Medium 0 44 38 65 115 05 3284 42 26 12 Ibs 28 23 Ibs High 0 57 66 85 150 27 4295 84 LISTED TOOLS REQUIRED Phillips Flat blade Step Wire Electrical screwdriver screwdriver ladder stripper tape Pre Installation continued HARDWARE INCLUDED NOTE Hardware shown to actual size unless noted otherwise in the table below
17. lots of the motor EEE with the tabs FFF the blade arms Tighten the two blade arm screws with lock washers Il already installed in the blade arms I Repeat this procedure for the remaining blade arms 1 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Installing the Light Kit 1 Attaching the switch housing to the mounting ring CAUTION Before starting installation disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box Turning power off using the fan switch is not sufficient to prevent electric shock A NOTE If you do not wish to install the light kit skip steps 11 through 13 and proceed to step 14 Remove one of the three switch housing mounting screws JJ from the mounting ring GGG and loosen the other two screws JJ Do not remove While holding the switch housing J under the fan motor assembly G snap together the wire connec tion plugs HHH Place the key holes in the switch housing J over the two screws JJ previously loosened from the mounting ring GGG Turn the switch housing J until the switch housing J locks in place at the narrow section of the key holes Securely tighten the two mounting plate screws JJ previously loosened and the one JJ previously removed 16
18. ng Mounting 9 Close to Ceiling Mounting 10 Hanging the succurrere revera evoca 11 Attaching the Fan Blades 14 Installing the Light KI 16 Operation p 18 Pull Chain Operating Instructions 18 Reverse Switch Operating Instructions 18 Care and Cleaning 19 Troubleshooting 19 Service 21 Safety Information 1 Toreduce the risk of electric shock ensure electricity has been turned off at the circuit breaker or fuse box before beginning not use this fan with any solid state fan speed control device j WARNING To reduce the risk of electrical shock or fire do It will permanently damage the electronic circuitry 2 All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 1999 and local electrical codes Electrical installation should be performed by a qualified WARNING Do not insert foreign objects between rotating licensed electrician fan blades 3 Theoutlet box and support structure must be securely mount
19. nt from the factory for a period of lifetime after the date of purchase by the original purchaser We also warrant that all other fan parts excluding any glass or acrylic blades to be free from defects in workmanship and material at the time of shipment from the factory for a period of two years after the date of purchase by the original purchaser We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned To obtain warranty service you must present a copy of the receipt as proof of purchase All costs of removing and reinstalling the product are your responsibility Damage to any part such as by accident misuse improper installa tion or by affixing any accessories is not covered by this warranty Because of varying climatic conditions this warranty does not cover any changes in brass finish including rusting pitting corroding tarnishing or peeling Brass finishes of this type give their longest useful life when protected from varying weather conditions A certain amount of wobble is normal and should not be considered a defect Servicing performed by unauthorized persons shall render the warranty invalid There is no other express warranty We hereby disclaim any and all warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law The duration of any implied warranty which cannot be disclaimed is l
20. ops into place firmly tightened Remove the fan from the hook on the mounting WARNING The locking slots of the canopy C are provided bracket A only as an aid to mounting Do not leave the fan assembly unattended until all four canopy mounting bracket screws BB are engaged and firmly tightened Secure the canopy C to the mounting bracket A with the four mounting bracket screws with lock washers BB provided Slide the canopy C up to the ceiling Make sure you have placed the wires safely into the outlet box PP Secure the canopy C to the mounting bracket A with the four canopy mounting bracket screws and lock washers BB included with your fan 13 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Attaching the Fan Blades 8 Removing the rubber packing mounts The fan motor assembly G is shipped with rubber packing mounts AAA to prevent movement during transportation Remove the five rubber packing mounts AAA from the fan motor assembly G and discard prior to attaching the blade arms 1 Attaching the blades to the blade arms WARNING Failure to properly seat the blades H on the blade arms and engage in the spring locking mechanism DDD could result in the fan blades H loosening and possibly falling NOTE Your fan blades are reversible Select
21. qualified electrician NOTE You may need a longer downrod to maintain proper blade clearance when installing on a steep sloped ceiling m The maximum angle allowable is 18 away from horizontal If the canopy C touches the hanger ball downrod assembly E then remove the decorative canopy bottom cover D and turn the canopy C 180 before attaching the canopy C to the mounting bracket A If your ceiling fan does not have an existing UL listed mounting box then install one using the following instructions Disconnect the power by removing the fuses or turning off the circuit breakers Secure the outlet box PP not included directly to the building structure Use appropriate fasteners and materials not included The outlet box and its bracing must be able to fully support the weight of the moving fan at least 35 Ibs Do not use a plastic outlet box The illustrations below show three different ways to mount the outlet box PP not included PP QQ N a PP To hang your fan where there is an existing fixture but no ceiling joist you may need an installation hanger bar QQ not included as shown above Assembly Standard Ceiling Mounting 1 Preparing the canopy 2 Preparing the motor Remove the canopy ring B from the canopy C Remove the clevis pin CC and cotter pin DD and loosen the two collar sets
22. the blade side finish which best accentuates your decor To install the blade to the blade arm Hold the blade H with hands close to the blade arm 1 align the key slot holes BBB with the blade arm posts CCC and press the blade down firmly Ensure the key slot holes BBB are properly seated on the blade arm posts CCC Firmly slide the blade away from the blade arm until the blade H engages in the spring locking mechanism DDD Make sure the spring of the spring locking mechanism DDD is upward and the butt of the spring locking mechanism DDD is against the edge of the blade To detach the blade from the blade arm Press down the spring locking mechanism DDD to release the blade from the blade arm Slide the blade toward the blade arm until the blade disengages from the spring locking mechanism DDD carefully push the blade H up to detach from the blade arm 14 Assembly Attaching the Fan Blades 1 Fastening the blade assemblies to the motor WARNING To reduce the risk of personal injury do not bend the blade arms while installing balancing the blades H or cleaning the fan Do no insert foreign objects between rotating fan blades H Fasten the blade assemblies to the fan motor assembly G by lining up the s
Download Pdf Manuals
Related Search