Lifegard Aquatics R440808 Installation Guide
Contents
1. twisting clockwise 7 Replace the front housing by gently squeezing the sides and pushing it straight in 8 SERVICING Quiet One 9000 14000 16000 series Pump Severe damage to the inside of the impeller chamber results from lack of maintenance or dry running and can void the warranty 3 Separate the Impeller and Rubber Gasket from the ceramic shaft and 2 Clean the inside chambers of all buildup and algae and check the inside of check all parts for cracks chips or any type of damage The plastic moving the impeller chamber with your finger to see if any grinding or warping parts of the impeller should be able to turn half a turn both clockwise and Pi T Counterclockwise before locking and being 5 unable to turn farther Ifit turns freely without locking the impeller is broken 4 Apply silicone lubricant to all moving parts plastic spinning parts on the impeller and inside the impeller where the ceramic shaft is inserted Allow the lubricant to properly seep in and cover all moving surfaces Also apply silicone lubricant to the rubber O Ring on the volute 5 Reassemble and close pump 1 Completely disconnect the pump from your system from the power outlet Unscrew the five retaining screws from the volute front housing then pull the volute straight out without turning it Warranty Policy Warranty period starts from date of purchase and must be valid2. gray front housing by g out until it coms off ently squeezing the sides and pulling 3 Twist the gray volute counte pull it straight out clockwise ur slips out of the groves then 6 Return the volute to its original position by fitting it into the securing grooves and twisting clockwise Ss J z 7 Replace the front housing by gently squeezing the sides and pushing it straight in SERVICING Quiet One 5000 6000 series Pump 1 Completely discon 2 Remove the gray front housing by gently squeezing the sides and pulling out until it coms off the pump from your system and the power outlet 4 Remove the impeller ceramic shaft assembly from inside the pump and examine it for signs of damage Inspect the inside of the impeler chamber to make sure there isn t any warping or grinding Severe damage to the inside of the impeller chamber can be caused by lack of maintenance or an instance of dry running and can void the warranty Apply silicone lubricant to both ends of the ceramic shaft to ensure optimal ree see teed pale performance and smooth running 5 Insert the impeller ceramic shaft assembly back into the impeller chamber 4 5000 6000 Aquarium Fountain Impeller 6 Return the volute to its original position k 4 by fitting it into the securing grooves and 3 Twist the gray volute counter clockwise until pull it straight out we amp a slips out of the groves then
3. part of the cord below the level of l the receptacle or the connector ifan extension cord is used which prevents water travelling along the cord and coming in contact with the receptacle Ifthe plug or socket does get wet DON T unplug the cord Disconnect the fuse or circuit breaker that supplies power to appliance Then unplug and examine for presence of water in the receptacle Close supervision is necessary when any appliance is used by near children To avoid injury do not contact moving parts or hot parts such as heaters reflectors lamp bulbs and similar Always unplug the appliance from the outlet when not in use before putting on or taking off parts and before cleaning Never yank cord to pull plug from outlet Grasp the plug and pull to disconnect Do not use the appliance for other than intended use The use of attachments not recommended or sold by the manufacturer of the appliance may cause an unsafe condition Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing 2 a gt Figure 1 DRIP LOOP P sa A 10 Make sure the appliance is installed and mounted securely before operating it 11 Read and observe all the important notices regarding the installation and Operation procedures 12 If an extension cord is necessary a cord with a proper rating should be used A cord rated for less amperes or watts than the appliance ratin
4. LIFEGARD uiet One Pur INSTRUCTIONS Models 800 1200 2200 3000 4000 5000 6000 9000 14000 and 16000 Quiet One Pumps feature a patented system that provides high hydraulic performance with lower energy consumption IMPORTANT SAFETY INSTRUCTIONS WARNING To guard against injury basic safety precautions should be observed including the following READ AND FOLLOW ALL SAFETY INSTRUCTIONS WARNING To avoid possible electric shock special care should be taken since water is employed in the use of aquarium equipment For each of the following situations do not attempt repairs by yourself Return the appliance to an authorized service facility for service or discard the appliance 1 CAUTION Ifthe appliance shows any sign of abnormal water leakage immediately unplug it from the power source Carefully examine the appliance after installation It should not be plugged in if there is water on parts not intended to be wet Do not operate any appliance if it has a damaged cord or plug or if it doesn t work properly or has been dropped or damaged in any manner To avoid the possibility of the appliance plug or receptacle getting wet Position the aquarium stand tank or the fountain to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug A drip loop fig 1 should be arranged by the user for each cord connecting an aquarium appliance to a receptacle The drip loop is the
5. ated with copy of original purchase receipt Warranty requests by phone will not be honored Warranty items returned without copy of original purchase receipt will not be honored Products purchased from EBay Craig s List etc cannot be honored for warranty unless returned by original purchaser with proof of purchase All items must first be returned to Lifegard Aquatics for inspection evaluation and processing to determine if product qualifies for warranty replacement or repair No warranty repair replacement or credit will be issued prior to inspection of product Please contact us first for warranty assistance Many times the product can be repaired without the cost and time involved in sending it back to us lf absolutely necessary return product freight prepaid to the following address for warranty evaluation and processing Lifegard Aquatics 13911 Struikman Road Cerritos CA 90703 Tel 562 404 4129 Fax 562 404 4159 Email info lifegardaquatics com 3 year warranty from date of purchase on Quiet One Pump Motors Only 60 day warranty from date of purchase on Shafts and Impellers for All Types of Pumps LiFEGARD AQUATICS 13911 Struikman Road Cerritos CA 90703 ess Pond amp Aquaculture Products Tel 562 404 4129 Fax 562 404 4159 Email info lifegardaquatics com
6. e applications and allows for variation of the flow rate and head of the pump Model 1200 Aquarium Fountain 2 A Models 1200 2200 3000 4000 5000 6000 version with long pre chamber Model 1200 1 2 Models 3000 4000 5000 6000 1 The threads are standard MPT and can be used with a vast range of fittings and accessories Fig4 and 5 INSTALLATION Models 9000 14000 amp 16000 Position the pump taking care that the isin an area where it cannot be damaged The pump may be sec vith screws through the special brackets situated on the bottom of the pump itself The pump is threaded both on suction and output with a 11 2 thread The thread is a standard MPT and allows use ofa vast range of standard fittings and accessories POND Models 9000 14000 16000 Filter Basket Fit the filter basket supplied Fig 7 following the sequence indicated Screw the coupling A 11 2 to the output of the pump then screw the hose adapter B 11 2 onto the coupling Screw the nut D 11 2 and the hose adapter 11 2 through the hole in the prefilter basket C and then close the 2 sections special hooks G provided 8 pcs Connect the flexible hose H 11 2 to the hose adapter on the pump and on the prefilter basket Water plays Install the water play as in the drawing Fig 8 Fix the diverter T valve flow adjuster 11 2 to the delivery of the pump then screw on in succession the sleeve L from 11 2 t
7. g may over heat and cause a safety hazard Care should be taken to arrange the cord so that it will not be tripped over or pulled 13 This appliance has a polarized plug one blade is wider than other As a safety feature this plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician Never use with an extension cord unless the plug can be fully inserted Do no attempt to circumvent this safety feature CAUTION Appliance must to be connected to a circuit that is protected by a Ground Fault Circuit Interrupter WARNING To reduce the risk of electric shock use only on portable self contained fountains no larger than 5 feet in any dimension SAVE THESE INSTRUCTIONS INSTALLATION Models 800 1200 2200 3000 4000 5000 amp 6000 see Pond section AQUARIUMS FOUNTAINS Position the aquarium and stand to one side of a wall mounted receptacle to avoid the possibility of water dripping onto the receptacle or plug Install a drip loop with the cord Model 800 The water flow rate is adjustable by means of the Flow Control Dial A Fig 2 The pump can be connected with 1 2 fittings and accessories Model 1200 version with submersible front housing The pump can be connected with 1 2 fittings and accessories on the output side The front housing with Flow Control Dial A Fig 3 is used in submersibl
8. he height of the telescopic antenna holding tube R F transmitter In the POND REMOTE version the pump functions are managed at a distance by the R F transmitter Fig 11 Once pump Laer installation has been completed insert the battery in the R F transmitter 12V Key Symbol Function 1 4 ON OFF press at the same time to turn pump ON or OFF 1 Speed increase speed and flow rate 4 Speed decrease speed and flow rate 2WP Water Play 3 TIMER Timer Touch3 Touch2 Touha Starting stopping the pump The pump is started by pressing the keys 1 and 4 simultaneously for about 2 seconds The pump is stopped by repeating the operation described above Increasing decreasing the speed and flow rate When the button1 is pressed the pump increases the speed and flow rate When the button 4 is pressed the pump decreases the speed and flow rate Water Play Features When the button WP is pressed only once Water Play Feature No 1 starts The jet of water grows to its maximum height remains in position for about 2seconds and then falls to the minimum value and remains there for about 2 seconds The sequence is repeated cyclically until it is changed When the button WP is pressed a second time Water Play Feature No 2 starts The jet of water grows to its maximum height stops for a few instants falls rapidly to about 1 4 rises to about 3 4 and pauses for a few insta
9. nd pull it out from the bottom 3 QuietOne 1200 groove then gently pull up and out to clear the securing tab on the top of the pump 3 Pull the impeller straight out of the impeller and steel shaft 4 Clean the pump and impeller chamber as well as the impeller Check the steel shaft for signs of rust or ifit wiggles or comes out of the pump Lubricate the impeller and steel shaft using silicone lubricant 5 Re insert the impeller into the impeller chamber then replace the gray housing making sure it fits into the securing tabs 1 Completely disconnect the pump from your system and the power outlet 2 QuietOne 800 2 QuietOne 1200 3 QuietOne 800 an 4 QuietOne 800 4 QuletOne 1200 QuietOne 800 1200 5 Quiet0ne 800 1200 SERVICING Quiet One 2200 3000 4000 series Pump 4 Remove the impeller ceramic shaft assembly from inside the pump and examine it for signs of damage Inspect the inside of the impeler chamber to make sure there isn t any warping or grinding Severe damage to the inside of the impeller chamber can be caused by lack of maintenance or an instance of dry running and can void the warranty Apply silicone lubricant to both ends ofthe ceramic shaft to ensure optimal performance and smooth running 5 Insert the impeller ceramic shaft assembly back into the impeller chamber 1 Completely disconnect the pump from your system and the power outlet 2 Remove the
10. nts falls again rapidly to about 1 4 and returns to maximum height The sequence is repeated cyclically until it is changed When the button WP is pressed a third time Water Play Feature No 3 starts The jet of water rises to about 1 4 of its height falls to minimum rises again to about 1 2 falls again to about 1 4 rises to about 3 4 falls again to 1 2 returns to maximum level then falls to zero level The sequence is repeated cyclically until it is changed Note The passage to the various water plays is sequential and progressive Whenever the WP key is pressed you move on to the next play WP1 WP2 WP3 WP1 WP2 etc e g To pass from WP3 to WP2 you must pass through WP1 and not the reverse Timer The time management system is represented in 8 hour fixed modules that are already programmed as follows a The pump is supplied already programmed in ON function at 50 of its power When it is connected to the electric outlet the pump starts automatically in the condition described b When the button 3 is pressed only once for about 2 seconds the pump works for 8 hours in ON and 16 hours in OFF When the button 3 is pressed a second time for about 2 seconds the pump works for 16 hours in ON and 8 hours in OFF d When the button is pressed again the pump returns to the initial ON function Note In the event of a black out or disconnection from the power outlet the
11. o 1 the pipe M 1 the sleeve N 1 the second pipe M 1 the second sleeve N and finally the jet nozzle P he prefilter basket C amp F using the i a oh Models 2200 3000 4000 Gg J gt wd y lt E gt S J yi O A pE Fountain 2 Aquarium boa ag gs Gina Models 5000 6000 w PONDS Slide the strainer onto the pre chamber then place the sponge in position on strainer Choose desired spray attachment and position on telescopic tube Screw telescopic tube onto pump Place pumpin pond Fig 6 ona flat surface away from over populated plant area Regulate the tube s height so the jet spray is always over the water surface Unwind electric cable and place in area where it cannot be damaged When pump is Models functioning you can regulate 800 the dimensions of spray using 1200 the diverter valve on the 3000 telescopic tube 4000 5000 6000 lt Yn Model 9000 oie low Model 14000 POND MODEL 14000 REMOTE Receiving antenna Install the external receiving antenna of the pump as follows Insert the antenna cable in the telescopic antenna holding tube provided as indicated in Fig 9 Insert the antenna holding tube in the special support in the rear part of the pump Fig 10 IMPORTANT The antenna cable must extend at least 8 20 cm above the level of the water by regulating t
12. pump always starts again in the ON position described in point a c To start the pump you must always repeat the programming of the desired functions IMPORTANT The indication that the signal has been transmitted to the pump is visibly shown by the jet of water which falls to minimum level for a few seconds To change the set program it is necessary to turn the pump OFF and then input the desired program FOR SAFETY REASONS IF THE MOTOR IS BLOCKED THE PUMP IS PROGRAMMED TO MAKE UP TO 20 ATTEMPTED STARTS THEN IT STOPS TO RESET STARTING YOU MUST SWITCH OFF THE POWER SUPPLY TO THE PUMP AND THEN SWITCH IT ON AGAIN PUMP MAINTENANCE Trouble Shooting If pump should stop working first check for the following 1 SHAFT BREAKAGE Open the pump and check if shaft is damaged or broken Replace ceramic shaft if needed 2 DIRTY ROTOR Sand calcium or debris can cause stoppage Open the pump and check for fragments of sand or debris If so disassemble rotor and rinse with fresh water Ifa white film of calcium remains rinse with vinegar lemon or any liquid suitable for removing calcium from solid surfaces that is also non toxic to fish and plants 3 NOISY PUMP Open the pump and check if debris has clogged the rotor If no obstructions are causing the noise replace the impeller assembly and shaft SERVICING Quiet One 800 1200 series Pump 2 Remove the gray front housing by squeezing it a
Download Pdf Manuals
Related Search