Catskill Craftsmen 51538 Instructions / Assembly
Contents
1. CATSKILL CRAFTSMEN Assembly Instructions Model 51538 Mid Sized Island w Flat Panel Doors amp Drop Leaf GENERAL 1 You have purchased model 51538 2 Should you need assistance or need to replace a damaged or missing part simply give us a call M F at 607 652 7321 from 7 30 am 4 30 pm EST and we ll send you the prepaid part via UPS usually that same day You may also email us info catskillcraftsmen com 3 Read the assembly instructions and the enclosed brochure before beginning assembly Assembly is easy if you read and follow the instructions step by step See our website for assembly tips and videos 4 Tools required Phillips screwdrivers medium and small medium flat blade screwdriver and a hammer 5 Drawer glides are sometimes pre packed with screws these are not used 6 Directions left right front back are given as facing the front of an assembled upright unit A friend is recommended to assist with assembly as this will ease the process Some of the parts are large and awkward to hold in place an extra pair of hands will help Parts List Model 51538 9 Back Panel 1 P N BP 51538 Side Panel 2 P N SP HDL 51538 h Top Front Brace 1 P N B 34 1 4 2 1 2 TF 51538 Glide Support 2 fis P N GLDSUP 51538 Bottom Front Brace 1 P2. B Attach the cabinet glide of the Drawer Glides to the Glide Support Stick using 5 8 7 flat head screws Left glide to left Side Panel right glide to right Side Panel The glides look almost alike however the right glide as you face the cart has a rolled lip at the top of the glide that keeps the drawer glide wheel in place Line up the holes in the glides so that the end with the wheel comes flush with the front edge of the Glide Support Stick Only 2 pilot holes are used in the glide support sticks C Attach the L brackets to the top of the glide supports using 5 8 7 screws Use the slot rather than the hole The hole will be used to attach the table top The L brackets should be flush with the top of the glide support sticks Note Cabinet drawer glides usually have an imprint CL or CR inside near the wheel CR Right CL Left 5 8 7 Screw TOP a TOP STEP 6 A Lay Back Panel flat on a smooth surface with holes up B Attach Side Panels with 1 3 4 bolts and hex nuts After inserting bolts s thru the holes in the Side Panels thru the holes in the long edges of the Back Panel place a hex nut on the tip of your finger align nut with bolt and tighten C Look ahead to step 7 which shows side panels attached to back panel NOTE Make sure you position the side panels according to Drawer Glides
3. left or right The Back Panel is 1 1 4 shorter than the Side Panels at the top STEP 7 A Invert cabinet assembly from step 6 B Take the Top Front Brace with magnet blocks insert the pins in the brace ends into the slots on the inside of the front legs of the Side Panel and slide down until the brace is aligned with the set of holes in the Side Panel as illustrated C Secure brace with 1 3 4 bolts and hex nuts as in step 6 a i LA STEP 8 A Install Doors by fitting the pins in the top of the door into the holes in the Top Front Brace B Place washers on the pins on the bottom of the doors then fit the Bottom Front Brace onto the pins and secure the brace using 1 3 4 bolts and nuts as in illustration 8A C Tap two 1 pins into the back panel two into the holes on the inside of the Bottom Front Brace i and two into each Side Panel as in 6 l illustration 8B These will hold the Bottom Shelf ILLUSTRATION 8A ILLUSTRATION 8B STEP 9 A Stick magnet to magnet plate on an outside door B With adjacent door open close the outside door The magnet should be positioned over the wooden block on the bottom of the top front brace Hold the magnet in place with your thumb and open the door The magnet will be in the correct position on the block Mark the po
4. N B 34 1 4 2 1 2 BOT 51538 Drop Leaf 1 P N DL 51538 Table Top 1 P N TT 51538 Drawer Front 1 P N DF 51538 Drawer Back 1 P N DBK 51538 Center Shelf 1 P N CS 51538 Drawer Bottom 1 P N DB 51538 Left Drawer Side 1 P N DS 51538L e Right Drawer Side 1 Bottom Shelf 1 P N BS 51538 I aft Danae 9 Diaht Naar 9 Hardware 51538 T PLATT 1 3 4 Phillips Flat Head Bolt 8 Nickel Handle 6 gt ii Bastion Post 2 off o 3 16 Flat Washer 8 10 24 Hex Nut 8 5 1 1 4 Phillips Flat Head 8 Screw 20 iili 5 8 Phillips Flat Head 8 Screw 20 A Use 8 Bronze screws E Puninannnnnnns for spice rack Bastion Set Screw 2 C Nime Used for drop laf hardware L Bracket 4 5 8 Wooden Disk 8 Bastion Barrel Nut 2 used to attach spice AANA eer Polished Nickel Towel Bar 1 1 Phillips Flat Head 8 Screw 4 oS Used to attach L bracket G Spice Rack Retaining Rods 2 and cabinet glides 5 8 Phillips Flat Head 7 Screw 12 Towel Bar Post 2 Drawer Ni Used to attach drawer glides 5 8 Philli
5. age to learn how the bastion fastening system works Also see our video on the Bastion Fastening System at www catskillcraftsmen com TIPS ON HOW THE BASTION FASTENING SYSTEM WORKS 1 The Bastion fastening system consists of a steel post threaded on one end with a hole through the shaft on the other end a Barrel Nut cylindrical barrel shaped with threaded open end amp holes through the sides and a Set Screw Phillips slot on one end pointed on the other 2 To attach Posts A Dip threads of Post in vegetable oil B Align threaded end of Post with hole in wood tap on slotted end with hard hammer until threads enter then tighten down using a flat head screw driver or the provided allen wrench See the Illus Bas 3 for alternate seating methods DO NOT TRY TO HAMMER THE POST ALL THE WAY IN AS IT WILL STRIP THE POST HOLE C When solid shaft of Post hits wood back out approximately turn until the hole in the posts is properly aligned as per step by step directions For example the holes in the posts on the inside of the drawer front will be parallel with the long length of the drawer front when properly seated 3 A Place a Barrel Nut into the nut access hole so that the threads in the nut face out The small notches on either side of the nut opening indicate the location of the holes through the sides of the nut B Insert the posts through the end of the braces or drawer sides through the holes in the sides of the nut When prop
6. atskill Craftsmen cart we recommend Catskill Craftsmen s Butcher Block Oil Our Butcher Block Oil is available direct ly from Catskill Craftsmen s factory For one eight ounce 8 fl oz bottle which is sufficient for two applications simply send 6 95 along with the completed coupon to the address below Visit us online at www catskillcraftsmen com to browse our assortment of butcher block care products Visa and Mastercard are accepted online A Catskill Craftsmen Inc C AT K LL 15 West End Ave CRAFTSMEN IN C Stamford NY 12167 1296 u aN CATSKILL C RAFTSMEN INC BUTCHER BLOCK OIL COUPON Please send me of bottle s of the Catskill Craftsmen Butcher Block Oil at 6 95 per bottle My check or money order is enclosed for a total of Item code 51538 Name Address City State Zip Please make checks payable to Catskill Craftsmen Inc 15 West End Ave Stamford NY 12167 1296
7. er Back to the Drawer Sides with four 1 1 4 8 screws There are left and right sides Make sure the slots that run the length of the Sides are aligned with the slot in the Drawer Back to accept the Drawer Bottom B Slide in Drawer Bottom best side up to inside of drawer C Take the 2 bastion posts align the threaded end of the posts with the post holes located near the ends of the inside of the Drawer Front Tighten posts down until the solid shaft of the posts hits the wood Back post out until the hole screwadriver slot in end of post is parallel and in direct line with the long edges of the Drawer Front D Insert the barrel nuts into the nut access holes on the inside of the Drawer Sides with the threaded ends of the nuts facing out Take the Drawer Front and carefully insert the posts into the ends of the Drawer Sides through the sides of the nuts until seated Push nut snug up against the wood in the nut access hole toward the inside of Drawer Front Hole should be slightly off center toward the Drawer Front Insert the set screw and tighten down The ends of the sides should be tight against the inside Drawer Front E Attach the drawer handles with 7 8 Truss head machine screws F Attach the drawer glides left and right to the Drawer Sides using two 5 8 5 screws per side Wheels go toward Drawer Back and are up The end with no wheels should touch the Drawer Front 7 ia 1 1 4 8 See next p
8. erly aligned you will see the hole in the post inside the barrel nut Post hole should be slightly off center toward the wood 4 Insert the Set Screw into the threaded end of the nut and tighten down The tip of the Set Screw will seek the center of the hole in the Post as it is tightened down forcing the Nut toward the main shaft of the Post This is what tightens the wooden parts together Set screws should thread easily DON T CROSS THREAD If Set Screw doesn t thread easily check position of the hole in Post 5 If the wooden parts are not tight against each other the Post needs to be screwed a half turn at a time until wood joints are tight Illustration Bas 1 WRONG Post needs to be screwed deeper WRONG Post needs to be backed out CORRECT Set screw secures post properly Illustration Bas 2 Illustration Bas 3 Step 1 M MU ALTERNATIVE METHODS FOR SEATING POSTS T T Allen Wrench Provided See video on our website If you have any questions regarding assembly or missing or damage parts call our customer support number 607 652 7321 or 888 732 7321 STEP 5 A Attach a Glide Support Stick to the top of each Side Panel using 1 1 4 8 screws The countersunk holes reamed out in the stick are positioned as in illustration 5 so that the glide holes are toward the lower edge Sticks should be flush with top of panel
9. ps Flat Head 5 Screw 4 a CN Used to attach drawer handles 7 8 Truss Head Machine Screw 12 0000 ins 1 1 2 Long 3 16 DIA Steel Pin 8 Shelf Pins A 1 Long 3 16 DIA Steel Pin 14 Hinge 2 Brace Pins mi 3 4 Long 3 16 DIA Steel Pin 4 Caster Socket 4 Magnet Packs 4 E tnie Used on Magnet Included in magnet pack 5 8 Pan Head Screw 8 N Used on Magnet Plate Included in magnet pack 1 2 Phillips Flat Head 4 Screw 4 O O O 0 U Locking Wheel Casters 2 Wheel Casters 2 Magnet Plate 4 Magnet 4 STEP 1 A Tap insert ONE 1 1 2 pin into each end of all the doors DON T OVERDRIVE PINS Pins should stick up about 1 2 when seated B Attach the magnet plate may be stuck to magnet with the 1 2 4 screw to the top of the doors Bumps go toward the wood C Attach door handles with 7 8 truss head machine screws STEP 2 A Take the 2 front braces and tap insert one 3 4 steel pin into each end of both braces until seated About 3 8 will stick out when seated OK if loose STEP 3 Pilot holes in shelves Assemble Spice Rack go toward back Fasten Shelves with 1 1 4 Phillips Flat Head 8 Screw Bronze www p O Insert retainer ye into holes O STEP 4 A Attach the Draw
10. s Then tap 1 pins into the 6 holes in the Back amp Side Panels B Fit the middle shelf into the cart and rest it on the pins STEP 14 A Assemble top by placing the top and the drop leaf upside down on a smooth flat surface Install hinges using 5 8 8 screws The longer part of the hinge goes on the drop leaf with the short part on the cart top Fasten the drop leaf supports using 5 8 8 screws See illustration 14B B Make a large X mark over each of the 4 pilot holes in the bottom Make marks about 1 2 1 long These marks will help you align the cabinet with the pilot holes in the bottom of the Top C Place the Cart Top on the cabinet Open the outside doors Maneuver the Cart Top so that the X marks pilot holes in the bottom of the Top align with the holes in the L brackets Secure top to L brackets with 5 8 7 screws ILLUSTRATION 14A ILLUSTRATION 14B STEP 15 A Slide the Drawer into the front of the cart Make sure drawer slides smoothly then retighten all bolts and nuts B Tap in the 5 8 wooden plugs into the holes on the legs C Illustration 15B shows completed 51538 ILLUSTRATION 15A As ILLUSTRATION 15B For continued beauty and long life of your C
11. sition with a pencil C Secure magnet with the two round head screws in the magnet packet Center screws in the slot in the magnet This will allow adjustment later if needed D Repeat these steps for all the doors Irti 8 Used in this step 5 8 Pan Head Screw No pilot holes as soft wood STEP 10 A Insert and tap caster sock ets with hammer until the teeth grab the wood DON T POUND SOCKET FLAT OR CASTER SHAFT WILL NOT ENTER B Insert casters and seat by pushing straight downward with heel of your hand or tap into place with a hammer Don t be afraid to give them a good downward whack on the solid metal part of the caster C Locking wheels usually go on front STEP 11 Upright unit Decide which side to put the spice rack on then put the towel bar on the other side At tach side handle towel bar using 1 Phillips Flat Head 8 screws Place a washer over the screw to keep screw heads from pulling through the side panels Attach the spice rack in the same way using the pilot holes in the top shelf The holes in the bottom shelf are not used Washer STEP 12 A Angle the bottom shelf as necessary to pass it through the opening in the cabinet top until it rests on the pins in stalled in step 8 STEP 13 A Set the height for the o middle shelf by choosing one of two sets of holes in the Back amp Side Panel
Download Pdf Manuals
Related Search