Home

DuPont WFDW120009W Instructions / Assembly

1. ner PET HH ourer HOT WATER COLD WATER VALVE VALVE O FLEXIBLE TUBING INSTALLATION V4 2 Installing Filter System to Auxiliary Faucet NOTE Installing a seperate Faucet for Filtered Water DuPont WFFT100 Series optimizes filter life and provides contaminant reduction STEP 1 Mount the Faucet for Filtered Water Not Included NOTE Most standard sinks come with 1 3 8 or 1 1 2 diameter water sprayer holes that can be used for mounting the Faucet If the pre drilled holes cannot be used or are not in the desired position a new hole must be drilled using either a 9 16 or 5 8 drill bit to accommodate the Faucet The Faucet for Filtered Water base should be positioned securely on a flat surface with adequate space for proper function Consider convenience and appearance of the faucet before installation Ah CAUTION NOTICE Safety glasses and a respirator are DO NOT DRILL THROUGH AN ALL PORCELAIN OR CAST IRON SINK If installing on an all porcelain or recommended for this process as it may cast iron sink the faucet must be mounted in a pre drilled sprayer hole or through the countertop next FAUCET FOR FILTERED WATER HOT WATER COLD WATER VALVE VALVE produce dust that can cause severe to the sink If the countertop must be drilled make certain that the area below the drilling location is on snai TE free of wiring and pipes Also make sure that the
2. Screw the Filter Housing back onto the System Head and hand tighten Using the Filter Housing Wrench tighten 1 4 turn NOTE Do not over tighten Check for any leaks before proceeding Turn on the cold water shut off valve and turn on the faucet Flush the system for 10 minutes Turn on the cold water shut off valve underneath the sink Turn on the new faucet for filtered water In order for the Filter System to flush the Filter Cartridge allow the water to run for approximately 10 minutes Check for any leaks between the System Head assembly and cartridge around all fittings on kitchen faucet adapter connection and on faucet tubing connection If there are leaks between the top of the kitchen faucet adapter and the kitchen faucet stem Turn off the cold water shut off valve underneath the sink Turn on the faucet for filtered water to release pressure and allow water to completely drain from the line Tighten the connection between the kitchen faucet adapter and the kitchen faucet stem If leaks continue remove the kitchen faucet adapter from the kitchen faucet stem and wrap the kitchen faucet adapter and the kitchen faucet stem with Teflon tape and re install Turn on the cold water shut off valve underneath the sink Turn on the faucet for filtered water Inspect for leaks If there are leaks between the bottom of the kitchen faucet adapter and the cold water supply line Turn off the cold water shut off valve underneath the
3. crimp 1 4 Plastic Tubing when inserting 4 Wetthe other end of the 1 4 Plastic Tubing with water and push it into the System Head Inlet approximately 5 8 until it stops 5 Determine the length of 1 4 Plastic Tubing that will be necessary to connect the System Head Outlet to the threaded faucet for filtered water Make sure to allow enough tubing to prevent kinking in the line 6 Cut the tube squarely on both ends 7 Gently slide the plastic compression nut down thread side up over the 1 4 Plastic Tubing Follow with the plastic ferrule making sure that the ferrule is in the proper position with the larger opening on the bottom going into the nut Place the plastic insert into the end of the 1 4 Plastic Tubing 8 Firmly push the 1 4 Plastic Tubing into the end of the threaded faucet stem Hand tighten the plastic compression nut onto the threads Tighten with an adjustable wrench approximately 1 2 turn NOTE Do not bend or crimp 1 4 Plastic Tubing when inserting Do not over tighten the compression nut 9 Wet the other end of the 1 4 Plastic Tubing with water and push it into the System Head Outlet approximately 5 8 until it stops Universal Drinking Water Series 7 V4 2 STEP 4 Install the Filter and Test the Filter System for Proper Operation 1 oOo a A WwW Insert the new Filter Cartridge over the standpipe in the bottom of the Filter Housing
4. sink Turn on the faucet for filtered water to release pressure and allow water to completely drain from the line Tighten the connection between the kitchen faucet adapter and the cold water supply line If leaks continue remove the kitchen faucet adapter from the cold water supply line and wrap the kitchen faucet adapter and the cold water supply line with plumber s tape and re install Turn on the cold water shut off valve underneath the sink Turn on the faucet for filtered water Inspect for leaks If there are leaks between the System Head and the 1 4 Plastic Tubing Turn off the cold water shut off valve underneath the sink Turn on the faucet for filtered water to release pressure and allow water to completely drain from the line Disconnect the 1 4 Plastic Tubing from the System Head Inlet and System Head Outlet Check the 1 4 Plastic Tubing to see if it is cut squarely If not re cut the ends squarely Wet the ends of the 1 4 Plastic Tubing with water and re insert into the System Head Inlet and System Head Outlet E f leaks continue turn off the water supply and call Customer Service Universal Drinking Water Series 8 FAUCET FOR FILTERED WATER not included HOT WATER COLD WATER VALVE VALVE RIGID TUBING INSTALLATION FAUCET FOR FILTERED WATER not included KITCHEN FAUCET HOT WATER COLD WATER VALVE VALVE FLEXIBLE TUBING INSTALLATION V4 2 Filter Cartridge Replacement STEP f Remove the Used Fi
5. the Mounting Bracket as a template mark the holes for positioning the Mounting Bracket on the wall surface 4 Using a 1 8 drill bit drill four pilot holes in the wall surface for the Mounting Screws Insert Mounting Screws through the Mounting Bracket and into the wall surface Tighten until secure E 5 SUGGESTED CLEARANCE CABINET BASE y A WARNING Ah CAUTION Be sure that all electrical appliances and outlets are turned off at the Please wear safety glasses to protect circuit breaker before working in cabinet area eyes when drilling Universal Drinking Water Series 3 V4 2 STEP 3 Connect Water Lines FOR RIGID TUBING 1 Disconnect the top of the cold water plumbing line from the faucet shank and gently bend the plumbing line for access to the lower line fitting 2 Screw the Kitchen Faucet Adapter E onto the lower end of the faucet shank 3 Screw the Kitchen Faucet Adapter E onto the upper end of the cold water line FOR FLEXIBLE TUBING 1 Disconnect the top of the cold water plumbing line from the faucet shank 2 Screw the Kitchen Faucet Adapter E onto the lower end of faucet shank 3 Screw the Kitchen Faucet Adapter E onto the upper end of the cold water line STEP 4 Connect the 1 4 Plastic Tubing FROM SYSTEM HEAD INLET TO KITCHEN FAUCET ADAPTER INLET PORT 1 Determine the length of 1 4 Plastic Tubing D that will be necessary to connect the System Head Inlet to the Kitchen Faucet Adapter at the shut o
6. water flow If you wish to maintain unfiltered water flow for dishwashing etc we recommend installing a seperate Faucet for Filtered Water DuPont WFFT100 Series STEP 1 Turn Off the Main Water Supply Line 1 Locate the cold water shut off valve under the sink Turn off the cold water supply to the existing kitchen sink NOTE If uncertain about which line supplies the cold water turn on the hot water to the faucet Allow the water to heat up and carefully feel the pipes under the sink The pipe that remains cool to the touch is the cold water supply COLD WATER VALVE 2 Turn on the cold water faucet on the kitchen sink to release pressure and allow water to completely drain from the line STEP 2 Install Bracket and Mount the System Head NOTE Mount the Filter System to a solid cabinet wall or wall If a solid surface is not available use hollow wall anchor bolts or toggle bolts not included to secure to the wall 1 Position the Mounting Bracket H on top of the System Head A aligning the four Mounting Bracket holes with the holes in the System Head Screw the Mounting Bracket securely onto the System Head using the four Mounting Screws provided 2 Choose an easy to access area under the sink to mount the Filter System NOTE To allow adequate space for filter cartridge changes allow a minimum clearance of 4 to 6 below the Filter Housing The Filter System must be mounted in a vertical position 3 Using
7. 441 7515 For Safety amp Health Questions Protect Plus LLC Hickory NC 28601 USA V4 2
8. Installation Instructions Universal Drinking Water Filters Instrucciones de instalaci n Sistema universal de filtrado de agua potable The miracles of science E ESE ij h l T N 0 a ad A A ml ae a qe e ee Ye ya ye Water Filtration Model Series WFDW12000 amp WFDW13000 Serie del modelo WFDW12000 amp WFDW13000 V4 2 Package Contents System Head Filter O Ring DuPont Part No WFA0200 li Filter Cartridge T Mounting Bracket DuPont Part No WFAB200 Ee Gun uo Filter Housing H Filter Housing Wrench DuPont Part No WFAW200 F Dual Port Kitchen Faucet Adapter DuPont Part No WFAF600 E 1 4 Plastic Tubing D DuPont Part No WFAF300 6 Feet Note Filter Cartridge included with system but not shown here 3 4 Mounting Screws 8 DuPont Part No WFAS300 Package of 2 Installation Instructions Universal Drinking Water Filtration System Parts amp Hardware Included Filter System System Head with Filter Housing Filter Cartridge varies with system purchased Filter O Ring 1 4 Plastic Tubing Direct Connect Kitchen Faucet Adapter Filter Housing Wrench Mounting Bracket IQ nmo D Mounting Screws 8 Information amp Assistance 866 709 2086 Tol Free For Service Requests amp Product Information Hours of Operation 24 Hours Day 7 Days Week 800 441 7515 For Safety amp Health Questions Tools amp Mat
9. and tighten Using the Filter Housing Wrench tighten 1 4 turn NOTE Do not over tighten Check for any leaks before proceeding Turn on the cold water shut off valve and turn on the faucet Flush the system for 10 minutes Universal Drinking Water Series 9 V4 2 Replacement Cartridges DuPont Universal Drinking Water Filtration System WFDW 12000 amp WFDW13000 Series Usage and quality of water in your incoming water line affect the life of filter cartridges and determine when the cartridge should be changed Cartridges should be replaced sooner if water pressure at the faucet begins to drop noticeably or if the filter fails to perform satisfactorily A filter cartridge s stated reduction capacity is tied to the cartridge s performance within a specific filtration system for which is it has been tested and certified Please see the Performance Data Sheet for the certified performance of specific systems with stated cartridges System Certification Cartridge Model Numbers Universal Drinking Water Filtration System WFDWC20001 WFDWC30001 WFDWC40001 WFDW12000 amp WFDW13000 Series WFDWC50001 WFDWC70001 Replacement Parts DuPont Universal Drinking Water Filtration System WFDW12000 amp WFDW13000 Series Part Number Description WFAB200 Mounting Bracket WFA0200 O Ring WFAW200 Filter Housing Wren
10. ch WFAS300 Mounting Screws Package of 2 WFAF600 Dual Port Kitchen Faucet Adapter Universal Drinking Water Series 10 CAUTION These filters are not water purifiers Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system Systems certified for Cyst reduction may be used on disinfected waters that may contain filterable Cysts This unit is not designed to filter sulfur rotten egg odor Use of carbon filters to treat sulfur may intensify taste odor problems Please comply with all state and local regulations regarding the installation of water treatment devices The contaminants or other substances reduced by the water filter device are not necessarily in your water Operation Maintenance Data These units are intended for non commercial use They should be used only in ambient air temperature of between 35 degrees F 2 degrees C and 100 degrees F 38 degrees C Placement of these units in direct sunlight or use of electrical heating equipment on these units must be avoided Replace filter cartridge when and as directed in the installation operation instructions included with each cartridge Replacement filter cartridges are available at retail outlets Ordering Information Installation Video www waterfiltration dupont com 866 709 2086 Toll Free For Service Requests amp Product Information Hours of Operation 24 Hours Day 7 Days Week 800
11. e flushed thoroughly Let water run for 10 minutes before using The filter cartridges used with this Filter System have a limited service life Changes in taste odor and or flow of the water being filtered indicate that the cartridge should be replaced This filter system provides stated contaminant reduction and capacity claims when used with an auxiliary faucet Before You Begin m Check under the sink to locate a solid wall surface to mount the Filter System NOTE The Filter System must be mounted in a vertical position m Determine if the Filter System will be used to filter water through the existing kitchen faucet page 3 or through auxiliary faucet page 6 for filtered water m Locate the cold water pipe under your sink and observe if it is a flexible hose or a rigid pipe ex plastic metal copper Rigid pipes may require cutting in order to make adequate space to install the fittings Also determine if you have all appropriate fasteners and adaptors to fit your plumbing E Consult your local plumbing codes and install accordingly Universal Drinking Water Series 2 KITCHEN FAUCET HOT WATER COLD WATER VALVE VALVE FLEXIBLE TUBING INSTALLATION FAUCET FOR FILTERED WATER KITCHEN FAUCET PURCHASED SEPARATELY al E HOT WATER COLD WATER VALVE VALVE V4 2 Installing Filter System to Your Kitchen Faucet Note Final filters reduce
12. erials Required Phillips Screwdriver Tape Measure Drill with 1 8 Drill Bit Pencil Safety Glasses Silicone Grease Pan or Bucket Optional Materials Hollow Wall Anchor Bolts or Toggle Bolts Plumber s Tape Faucet for Filtered Water DuPont Part No WFFT110 Kitchen Faucet Adapter Drill with 1 4 amp 9 16 or 5 8 Drill Bits Pipe Cutter or Hacksaw The DuPont WFFT110 Faucet for Filtered Water is highly recommended for use with this Filter System See Page 6 p Installation Video www waterfiltration dupont com o Protect Plus LLC M Hickory NC 28601 USA For installations in Massachusetts the Commonwealth of Massachusetts Plumbing Code CMR248 shall be adhered to Proper Installation Please read all instructions specifications and precautions before installing and using your water filter system NOTICE NOTICE This filter must be protected Because of the product s limited service life and to prevent costly repairs or possible water damage we strongly from freezing which can recommend that the housing be replaced every five years If the head of the filter has been in use for longer than cause cracking of the filter this period it should be replaced immediately Date the top of any new head to indicate the next recommended and water leakage replacement date Precautions For cold water use only After prolonged periods of non use such as during a vacation it is recommended that the system b
13. ff valve Make sure to allow enough 1 4 Plastic Tubing to prevent kinking in the line 2 Cut the 1 4 Plastic Tubing squarely on both ends 3 Wet one end of the 1 4 Plastic Tubing with water and push it into the System Head Inlet until it stops NOTE Do not bend or crimp 1 4 Plastic Tubing when inserting 4 Wet the other end of the 1 4 Plastic Tubing with water and push it into the Kitchen Faucet Adapter Inlet Port A until it stops NOTE Do not bend or crimp 1 4 Plastic Tubing when inserting FROM SYSTEM HEAD OUTLET TO KITCHEN FAUCET ADAPTER OUTLET PORT 5 Determine the length of 1 4 Plastic Tubing D that will be necessary to connect the System Head Outlet to the Kitchen Faucet Adapter on the lower end of the plumbing line Make sure to allow enough 1 4 Plastic Tubing to prevent kinking in the line 6 Cut the 1 4 Plastic Tubing squarely on both ends 7 Wet one end of the 1 4 Plastic Tubing with water and push it into the System Head Outlet until it stops NOTE Do not bend or crimp 1 4 Plastic Tubing when inserting 8 Wet the other end of the 1 4 Plastic Tubing with water and push it into the Kitchen Faucet Adapter Outlet Port until it stops NOTE Do not bend or crimp 1 4 Plastic Tubing when inserting Universal Drinking Water Series 4 COLD WATER LINE RIGID TUBING V4 2 STEP 5 Install the Filter and Test the Filter System for Proper Operation 1 Oo ol A 0 Insert the new Filter Cart
14. llow the water to heat up and carefully feel the pipes under the sink The pipe that remains cool to the touch is the cold water supply 2 Turn on the cold water on the kitchen sink to release pressure and allow water to completely drain from the line continued to next page RIGID TUBING INSTALLATION Universal Drinking Water Series 6 V4 2 STEP 2 Install the Kitchen Faucet Adapter Not Included continued El dial 3 Disconnectthe cold water line from the 1 2 threaded stub on the bottom of the kitchen faucet 4 Connectthe kitchen faucet adapter to the kitchen faucet stub 5 Ifyou have a rigid plumbing pipe it may be necessary to shorten the pipe Remove any burrs with a metal file ull A WARNING CAUTION Be sure that all electrical appliances and outlets are turned off at the Please wear safety glasses to protect ae circuit breaker before working in cabinet area eyes when drilling 6 Connect the cold water supply line to the kitchen faucet adapter securely STEP 3 Connect Water Lines VALVE VALVE 1 Determine the length of 1 4 Plastic Tubing D that will be necessary to connect the System Head Inlet to the kitchen faucet adapter Make sure to allow enough tubing to prevent kinking in the line INSERT 2 Cutthe tube squarely on both ends FERRULE 3 Wet one end of the 1 4 Plastic Tubing with water and push it into the kitchen faucet adapter approximately 5 8 until it stops NOTE Do not bend or
15. lter Cartridge 1 4 Turn off the cold water supply to the existing kitchen sink NOTE If uncertain about which line supplies the cold water turn on the hot water to the faucet Allow the water to heat up and carefully feel the pipes under the sink The pipe that remains cool to the touch is the cold water supply Turn on the cold water faucet on the kitchen sink to release pressure and allow water to completely drain from the line Use the Filter Housing Wrench G to unscrew the housing NOTE Use a pan or bucket to catch any water in the housing Pour out the water in the Filter Housing and remove the used Filter Cartridge B STEP 2 Clean the Filter System NOTE Have a pan or bucket handy to rinse out the Filter Housing 1 Oo oa A 0 N Rinse out the bottom of the Filter Housing Wash the Filter Housing with mild soap and water Do not use harsh cleansers or hot water Rinse the Filter Housing with clean water to remove all bleach Remove the Filter O Ring C in the top of the Filter Housing and wipe clean Use silicone grease food grade to lubricate the Filter O Ring Place the Filter O Ring back in the grooves of the Filter Housing NOTE Make sure that the O Ring is seated properly in the groove to ensure a good seal STEP 3 Add New Filter Cartridge and Test System 1 2 Insert the new Filter Cartridge over the standpipe in the bottom of the Filter Housing Screw the Filter Housing back onto the System Head and h
16. re is sufficient room to make the proper connections irritation It ICIS inhaled or comes iN Contact tothe bottom of the faucet mount DO NOT DRILL THROUGH COUNTER TOPS MORE THAN 1 IN with eyes THICKNESS OR COUNTER TOPS MADE OF TILE MARBLE GRANITE OR SIMILAR SUBSTANCE Consult with a plumber or counter top manufacturer for assistance IF YOUR SINK DOES NOT HAVE A WATER SPRAYER HOLE GO TO 1 IF YOUR SINK DOES HAVE A WATER SPRAYER HOLE GOTO 4 1 In order to prevent parts and materials from falling down the drain line the sink with newspaper or a towel 2 Apply masking tape to the area to be drilled in order to prevent scratching the sink surface or countertop if the drill bit slips during operation 3 Using a center punch mark the drill hole Use the 1 4 drill bit to make a pilot hole Then use the 9 16 or 5 8 drill bit to drill the final hole Drill completely through the sink or countertop and smooth the rough edges with a file 4 Mount the faucet for filtered water according to the installation instructions that came with the faucet you purchased STEP 2 f rm ou Install the Kitchen Faucet Adapter Not Included NOTE Our DuPont WFFT100 Series Faucets for Filtered Water come with a Kitchen Faucet Adapter 1 Locate the cold water shut off valve underneath the sink Turn off the cold water supply to the kitchen faucet NOTE If uncertain about which line supplies the cold water turn on the hot water to the faucet A
17. ridge over the standpipe in the bottom of the Filter Housing Screw the Filter Housing back onto the System Head and hand tighten Using the Filter Housing Wrench tighten 1 4 turn NOTE Do not over tighten Check for any leaks before proceeding Turn on the cold water shut off valve and turn on the faucet Flush the system for 10 minutes Slowly turn on the cold water shut off valve underneath the sink Turn on the kitchen faucet In order for the Filter System to flush the Filter Cartridge allow the water to run for approximately 10 minutes Check for any leaks between the System Head and Filter Housing of the Filter System and on the inlet and outlet connections If there are leaks between the System Head and Filter Housing of the Filter System EH Turn off the cold water shut off valve underneath the sink m Turn on the kitchen faucet to release pressure and allow water to completely drain from the line m Unscrew and remove the Filter Housing from the System Head using the Filter Housing Wrench F NOTE Use a pan or bucket to catch any water in the housing Remove the Filter O Ring C and inspect Clean and lubricate with silicone grease Clean the grooves in the top of the Filter Housing where the Filter O Ring sits Place the clean lubricated Filter O Ring back in the groove Turn on the cold water shut off valve underneath the sink Turn on the kitchen faucet Inspect for leaks If there are leaks between the fittings and sh
18. ut off valve flexible tubing or rigid tubing Turn off the cold water shut off valve underneath the sink Turn on the kitchen faucet to release pressure and allow water to completely drain from the line Tighten all fittings securely Turn on the cold water shut off valve underneath the sink Turn on the kitchen faucet Inspect for leaks If leaks continue disconnect all fittings and add plumber s tape to threads and retighten If there are leaks between the System Head and the 1 4 Plastic Tubing Turn off the cold water shut off valve underneath the sink Turn on the kitchen faucet to release pressure and allow water to completely drain from the line Disconnect the 1 4 Plastic Tubing from the System Head Inlet and System Head Outlet Check the 1 4 Plastic Tubing to see if it is cut squarely If not re cut the ends squarely Wet the ends of the 1 4 Plastic Tubing with water and re insert into the System Head Inlet and System Head Outlet Turn on the cold water shut off valve underneath the sink Turn on the kitchen faucet Inspect for leaks E f leaks continue turn off the water supply and call Customer Service Universal Drinking Water Series 5 Screw the Filter Housing back onto the System Head and hand tighten Using the Filter Housing Wrench tighten 1 4 turn amer HOT WATER COLD WATER VALVE VALVE RIGID TUBING INSTALLATION O

DuPont WFDW120009W Instructions / Assembly

Contents

Download Pdf Manuals

Related Search

Related Contents