Culligan CULLIGAN-RVF-10 Instructions / Assembly
Contents
1. the filter housing and screw back onto the filter cap DO NOT OVERTIGHTEN 6 Before running water through the RVF 10 system into the storage tank flush out any carbon fines that may be present in the carbon cartridge Disconnect the hose at the storage tank and turn the water supply on for approximately one minute Turn off water supply and reconnect the hose to the storage tank The replacement cartridge should be changed when the orig inal foul tastes or odors appear or when there is a noticeable drop in water pressure at the filter housing outlet Culligan International Company One Culligan Parkway Northbrook Illinois 60062 www culligan com 2003 Culligan International Company Printed in U S A Customer Service M F 7 30 a m 5 00 p m CST Phone 1 800 634 1455 Fax 1 888 749 8826 International Phone 920 457 9435 Fax 920 457 2417 e mail customerservice culligan com male hose short hose to storage tank filter housing When the RVF 10 system is not being used for a period of time the cartridge should be removed and drained of excess water The cartridge should be air dried When the system is to be used again the flushing procedure should be followed See step 6 of Cartridge Replacement instructions TROUBLESHOOTING Leaks between cap and bottom of housing L Turn off water supply and remove bottom of filter housing 2 Clean O ring and O ring groove located directly beneath threads o2. f f Recreational Vehicle M arine Water Filter System Installation and Operation Instructions The RVF 10 system is designed to reduce foul tastes odors and sediment from potable drinking water This system includes 3 4 flexible hose couplings and the NCP 10 replacement cartridge NOTE This system may reduce water flow slightly INSTALLATION L Wrap the 3 8 inch fitting on the 3 4 inch female hose adapter with Teflon tape included and screw into the INLET side of the filter system Wrap the male hose adapter with Teflon tape and screw into the OUTLET side of the filter system Use a wrench to tighten firmly DO NOT OVERTIGHTEN About one thread should remain visible when fittings are tightened 2 To protect the system from possible damage install the system between two hoses The short hose included should be used to connect the outlet side of the filter system with the storage tank inlet A sanitary hose can be used to connect the water faucet to the inlet side of the filter system 3 Before running water through the RVF 10 system into the storage tank flush out any carbon fines that may be present in the carbon cartridge Disconnect the hose at the storage tank and turn the water supply on for approximately one minute Turn off water supply and reconnect the hose to the storage tank Installation is now complete WARNING Do not use with water that is microbiologically unsafe or of unknown quality witho
3. f housing Lubricate O ring with petroleum jelly Vaseline and replace securely into groove Screw bottom of housing onto cap and hand tighten Leaks on inlet outlet connections L Turn off water supply 2 Tighten fittings 1 2 turn Do not overtighten If leaks persist call Technical Support at 1 800 645 5426 REPLACEMENT PARTS Filter Cap Filter Housing O ring OR 38 not shown Hose Hose Fitting Kit Spanner Wrench SW 1 optional CARTRIDGES NCP 10 included Sales amp Marketing Correspondence PO Box 1086 Sheboygan WI 53082 1086 Fax 847 291 7632 e mail sales marketing culligan com 11 03 145808 Rev C
4. ut adequate disinfection before or after the system CAUTION The RVF 10 system must be protected from freezing Failure to do so may result in cracking of the filter and water leakage RVF 10 Pap M avert til i AAR hi HW Hy iA Mi iy Ni IXY Mi Ai Nh MM Nt Hi Nt HY HR HM IY IAN HN MON MN i ANY A Gn a Ky it HK aK Wi ih Hh ANA Mitt NAN N it i HM Wh nh Hh iM Ha ON Hi it o female hose INSTALLATION Hy i Hl water supply hose not included CARTRIDGE REPLACEMENT L To change the cartridge turn off the water supply and depress the red pressure relief button 2 Unscrew the filter housing Remove and discard the existing cartridge 3 Rinse out the filter housing and scrub the inside with mild soap and warm water using a non abrasive Sponge Also scrub the inside areas of the filter cap Rinse thoroughly with clean water 4 Remove O ring from the groove in the housing and wipe groove and O ring clean Lubricate O ring with a coating of clean petroleum jelly Vaseline Place O ring back in the groove and wipe or press it down into the groove using two fingers NOTE The rubber O ring provides a water tight seal between the cap and the bottom of the housing It is important that the O ring be properly seated in the groove below the threads of the housing or a water leak could occur 5 Place the new cartridge into
Download Pdf Manuals
Related Search