Fluidmaster 7503 Installation Guide
Contents
1. liable 2 Hex Nuts for use of non Fluidmaster parts during installation or repair e Plastic Retainer Washers FLOOR BOLT DO NOT LUBRICATE THE 0 RINGS PLASTIC RETAINER FLOOR FLANGE WASHER NOT INCLUDED 1 TOILET BOWL amp FLOOR FLANGE PREPARATION 2 CHECK FIT ON BOWL 3 DRAIN PIPE PARTS amp ASSEMBLY Turn off water supply Flush tank and bowl Sponge out Before installing bowl gasket press it onto the a On the 3 Wax Free Bowl Gasket place a thick O ring remaining water in tank and bowl Disconnect water supply horn of bowl to check fit If gasket goes on horn OQ at the bottom of the gasket just above the four line at toilet tank Now take bolt caps if present off base but does not cover completely use sand paper on flanges If you can t insert the gasket with the thick of bowl Remove nuts from bolts at base of bowl Lift the horn to bring into round Test fit before J O ring into the drain pipe then use the thin O ring bowl off of bolts and safely lay bowl on its side proceeding to next step If gasket will not cover instead O ring thick or thin place at bottom of bow gasket base Place a rag in the hole to block sewer gas odor Temporarily horn at all you will have to use wox ring instead cover the floor flange with a bucket until you are ready to begin installation on new bowl gasket If a wax ring was used previously then use a putty knife to remove old wax from floor flange a2. Express Warranty Fluidmaster Inc will provide subject to the Exclusions section set forth below all replacement parts free of charge necessary to correct such defects This Limited Ten Year Warranty is null and void if this plumbing product has not been installed and maintained in accordance with all written instructions accompanying the product and if non Fluidmaster Inc parts are used in installation Exclusions SST SHALL NOT BE LIABLE FOR INCIDENTAL ACCORDANCE WITH THE WRITTEN INSTRUCTIONS INCLUDING USE OF NON FLUIDMASTER PARTS DO NOT USE IN TANK DROP IN TOILET BOWL CLEANERS CONTAINING BLEACH OR CHLORINE USE OF SUCH PRODUCTS WILL RESULT IN DAMAGE TO TANK COMPONENTS AND MAY CAUSE FLOODING AND PROPERTY DAMAGE USE OF SUCH PRODUCTS WILL VOID THIS WARRANTY C Floor bolts are not secured properly 30800 Rancho Viejo Road D Uneven floor May require shims PRODUCT FROM OVERTIGHTENING OF FROM FAILURE TO San Juan Capistrano CA 92675 INSTALL OR MAINTAIN THIS PLUMBING PRODUCT IN www fluidmaster com Contact Fluidmaster for troubleshooting help or Ask Bob on www fluidmaster com Fluidmasterlnc 800 631 2011
3. PART 5 1007 Grev 4 10 11 FLUIDMASTER 7503 WAX FREE BOWL GASKET TOOLS NEEDED FOR INSTALLATION e Putty knife zZ TO REMOVE A PRE EXISTING FLUIDMASTER BOWL GASKET KIT INSTALLATION INSTRUCTIONS e Pliers or adjustable wrench oO 1 Make two loops of string and place the loops between the floor flange and the bowl gasket Hacksaw _ 2 Pull the string loops outward in opposite directions NOTE SAVE INSTRUCTION SHEET FOR FUTURE REFERENCE e Wire brush ior ar lt 3 Pull the string loops upward toward the center making sure they rest between hooks on the howl tae and Rag ee gasket Insert screwdriver as shown and pull upward to remove bowl gasket from drain pipe a Qa DO NOT USE IN TANK DROP IN TOILET BOWL CLEANERS CONTAINING BLEACH OR CHLORINE Use of such D 0 N oT USE Oi ica BOLT CAP BASE Lid products will 1 RESULT IN DAMAGE to tank components and MAY CAUSE FLOODING and PROPERTY e2 O Rings 1 thin 1 thick ee ce DAMAGE and 2 VOID FLUIDMASTER WARRANTY Fluidmaster Flush n Sparkle Toilet Bow Cleaning System Ings A UN e Bow HORN A e Cardboard Spacer is recommended for those choosing to use in tank bowl cleaners and WILL NOT VOID the FLUIDMASTER e 2 Bolts 2 Stainless Steel Washers WARRANTY because it will not damage the components DO NOT overtighten nuts or tank bowl may crack Always use quality Fluidmaster parts when installing or repairing Fluidmaster will not be responsible or
4. esigned to collapse and remain in place once the toilet is installed It will not interfere with the seal of the bowl gasket A Slightly insert the bowl gasket assembly into the drain pipe Before completely installing wrap the cardboard spacer around the bowl gasket and secure at the two cut corners INSTALLATION CAUTION If floor flange is above the floor and toilet rocks after installation you may need to call a professional to correct this condition before installing the Bowl Gasket SEE TROUBLESHOOTING If toilet rocks after installing it may be Subject to the Exclusions set forth below Fluidmaster Inc romises to the consumer to repair or at the option of A Floor flange is too high above the floor The floor flange needs to be lowered or floor raised to correct this condition B Bowl Gasket is not completely inserted in the drain pipe e Pipe rust may be obstructing Bowl Gasket The drain pipe is offset Bowl Gasket will not work with this condition e The drain pipe makes 90 degree turn so that Bowl Gasket bottoms out TROUBLESHOOTING LIMITED WARRANTY Fluidmaster Inc to replace any part of this plumbing product which proves to be defective in workmanship or materials under normal use for Ten years from the date of purchase All costs of removal transportation and reinstallation to obtain warranty service shall be paid by the consumer During this Limited Ten Year
5. nd under side of toilet Clean the bow horn and floor flange with a stiff brush 3 BOWL GASKET PREPARATION CONT E Place bolt cap base not included stainless steel washer then hex nut on bolt Tighten just enough to prevent movement of the toilet bowl DO NOT OVERTIGHTEN or bowl may crack If floor bolts are too long to allow the bolt caps to fit carefully cut the floor bolts with hacksaw to correct length Install bolt caps not included Reconnect tank to bowl Reconnect water supply connector to tank fill valve Turn on water supply D Line up holes in toilet base with floor bolts in floor flange This will line up the top of the bowl gasket with the horn on the bottom of the toilet bowl Lower toilet Apply weight to get toilet to rest on the floor C Connect floor bolts to floor flange by inserting floor bolts head down into mounting adjustment slots on floor flange Slide plastic retainer washers down the threads to hold bolts in place B Slowly and evenly push the bowl gasket assembly downward into the pipe until it is positioned 1 above the floor surface It may or may not touch the spacer depending on your floor and floor flange This will allow the bowl horn to contact the rubber opening of the bowl gasket before the bowl touches the floor The O ring should roll into the drain pipe and will move up the bowl gasket assembly as needed fo create a tight seal The cardboard spacer is d
Download Pdf Manuals
Related Search