ShelterLogic 86070.0 Instructions / Assembly
Contents
1. Securely fasten all of the joints with the hardware indicated 800383 DETAIL B End Ribs 11131 2 3 4 Bolt All Connections 800435 16 FT HIGH MODEL ONLY 800383 See next page for 800391 20ft high model 800384 TN DETAIL C Middle Ribs 800859 oe Page 5 05_10B163_0E 2b ASSEMBLE END AND MIDDLE RIBS 20 FT HIGH Assemble end and middle ribs as shown in Detail B and Detail C Securely fasten all of the joints with the hardware indicated 800383 800391 Ss 800384 800389 800390 800386 11131 2 3 4 Bolt DETAIL B All Connections End Ribs 800438 20 FT HIGH 800435 MODEL ONLY See previous page for 16ft high model ws TN 800386 _ DETAIL C 800438 Middle Ribs S 800436 800859 d Page 6 05_10B163_0E 3 INSTALL SIDE RAILS AND SHELTERLOCK STABILIZER BLOCKS A Place assembled first end rib in the staked area Place the ShelterLock on the upright as shown in F Detail D From the outside of the rib insert the bolt N through the upright and then through the ShelterLock DETAIL D B Place the plain end of the side rail over the bolt and nest it into the ShelterLock Install the nut onto the bolt and tighten Repeat these steps for the opposite side and all of the remaining ribs The side rails for the last rib will have two plain ends NOTE Sliding Cover Rail 11105 should be attached2. adjust the cover front to back so that it is centered When the cover is centered tighten all of the ratchets Do this in an X pattern to be sure it is tightened evenly See Detail O D Install the bottom cover rails 11102 and 11104 by inserting them into the pipe pockets on each side of the cover A 6 opening allows webbing to wrap around cover rail and base rail to secure cover Tighten webbing using ratchet as shown in Detail P Thread Webbing Into Ratchet Webbing and Ratchets Securing Cover DETAIL O NOTE CHECK THAT YOUR COVER IS CORRECTLY PLACED ON THE FRAME The ShelterLogic logo should line up on the left front and right rear corners near the top rail If the logo is not legible the cover has not been put on the frame correctly SLOT CENTERED IN POCKET SLIDE WEBBING THROUGH SLOT AND RATCHET AS SHOWN THEN TIGHTEN COVER DOWN STARTING AT ONE END WORKING TO OPPOSITE END ON BOTH SIDES DETAIL Q ASSEMBLED COVER RAIL Cover Tightening Tip Check and tighten Ratchets and Cross Rails monthly to ensure the cover is tight DOOR AND COVER OF SHELTER REMOVED FOR CLARITY SEE DETAIL Q WARNING Serious injury to persons or property could result if cover is installed and shelter is not completed and is left unattended Shelter must be securely anchored until completed Page 12 05_10B163_0E
3. e eROSS RAI PLAINEND 2H eae O o e TRUSS BRACE swe sexteeomxrzr mranenn eooo ITEM DESCRIPTION PART NO Page 4 3 28 16 Top Rail BOTTOM CROSS RAIL SWEDGED 802050 BOTTOM CROSS RAIL 802051 ATTENTION FOR MISSING OR REPLACEMENT PARTS OR QUESTIONS PLEASE CONTACT CUSTOMER SERVICE 1 800 524 9970 CANADA 1 800 559 6175 ix ShelterLogic www shelterlogic com 150 Callender Road Watertown CT 06795 05_10B163_0E BASIC FRAME ASSEMBLY NOTE FOR FRAME EXTENSION KIT 30 x 20 x 16 is the base frame dimension Your model may have more middle ribs than shown in the illustrations You will receive one extra rib for every extra 4 feet of building length that you purchase The basic frame assembly will remain the same The cover will be the correct size for the lt 30 _ length of the building ordered 1 PLOTTING AND SQUARING UP THE FRAME A Before building your shelter you should choose a flat area on your property and plot your shelter Stake out the area for DETAIL A the frame in the desired spot Check that it measures 26 in width and the length would be determined by the size shelter LENGTH you purchased Tie a rope diagonally from corner to corner OF BUILDING B Measure across area end to opposite end See Detail A The measurement A and B should be equal 2a ASSEMBLE END AND MIDDLE RIBS 16 FT HIGH Assemble end and middle ribs as shown in Detail B and Detail C
4. END DOOR PANEL INSTALLATION A Hold end panel at the top center with white inner surface facing inside of the shelter If you purchased the white cover the inner face has the visible weld seams Wrap the edges of the fabric panel around the end rib B Disconnect top rail the horizontal pipes that run from front to back along the top from the end rib Pull the webbing the black strap below the cross rail Attach top cross rail to end rib C Remove the nut from the side rail and carefully pull the side rail away from the ShelterLock pull away only enough to pass the webbing through the connection If this connection has the wind brace on it re move the wind brace end before pulling the side rail Replace the cross rail and wind brace Replace the nut and tighten Repeat this on the other side See Detail H D At the bottom where the webbing exits the pocket on each side of end panel pull webbing to remove the slack Be careful not to pull the webbing through the other side of the webbing pocket blei 48 Do Not insert any pipes into these pockets E Insert the S Hook on ratchet into hole on the leg bend Insert the webbing into the spindle of the ratchet and pull tight Wind the ratchet so that the webbing overlaps itself Position the end panel so that it is centered on the building before fully tightening the end panel F Tighten ratchets alternating from one side to the other until the end panel is centered and tight D
5. FRAME The ShelterLogic logo should line up on the left front and right rear corners near the top rail If the logo is not legible the cover has not been put on the frame correctly END PANELS AND WIND BRACES NOT SHOWN FOR CLARITY DETAIL J COVER RAIL SHOWN ASSEMBLED DETAIL K Page 10 05_10B163_0E 9 SLIDING COVER RAIL ASSEMBLY A After cover is installed and centered on frame Insert PN 11105 Sliding cover rail into pocket on cover top B Inside slits pockets in cover top bolt 3 and 4 Way Clamps cover and cover rail together and in to place on the frame See Detail N NOTE Round head of carrage bolts should be touching cover C On end panels look for open slit and insert clamps inside shelter D Pull cover top tight and tighten bolts DETAIL N End Rib Cross Rail Clamps Middle Rib Cross Rail Clamps 11106 11107 4 WAY CLAMP MID RIBS N RTS A rA L Page 11 05_10B163_0E 10 SECURING YOUR COVER A Insert the S Hook on ratchet into hole on the leg bend Insert the webbing into the spindle of the ratchet and pull tight Wind the ratchet so that the webbing overlaps itself B Insert the webbing end through the spindle of the ratchet and pull tight See Detail P Wind the ratchet until the webbing overlaps itself Repeat these steps on the opposite side then repeat this on the back side of the shelter C When all of the corners are secured
6. ShelterLogic LLC warrants to the Original Purchaser that if properly used and installed the product and all associated parts are free from manufacturer s defects for a period of 1 YEAR FOR COVER FABRIC END PANELS AND FRAMEWORK Warranty period is determined by date of shipment from ShelterLogic LLC for factory direct purchases or date of purchase from an authorized reseller please save a copy of your purchase receipt If this product or any associated parts are found to be defective or missing at the time of receipt ShelterLogic LLC will repair or replace at it s option the defective parts at no charge to the original purchaser Replacement parts or repaired parts shall be covered for the remainder of the Original Limited Warranty Period All shipping costs will be the responsibility of the customer Parts and replace ments will be sent C O D You must save the original packaging materials for shipment back If you purchased from a local dealer all claims must have a copy of original receipt After purchase please fill out and return warranty card for product registration Please see warranty card for more details Covered by U S Patents and patents pending 6 871 614 6 994 099 7 296 584 D 430 306 D 415 571 D 414 564 D 409 310 D 415 572 080310 Page 2 05_10B163_0E 30 W x 16 or 20 H Peak Style Frame Assembly 10B163 Please read and understand instructions completely before assembly Lay out frame parts as shown 5 27 1
7. to frame after Step 9 once cover is installed See Step 10 4 INSTALL WIND BRACES Attach wind brace between the end rib and the first middle rib as shown in Detail E Bolts attached at the cross rails should be inserted facing inside the shelter FIRST MIDDLE RIB DETAIL E oe WIND BRACE 800442 on 20 high only IND BRACE 800440 for 16 and 20 high Page 7 05_10B163_0E 5 INSTALL TOP RAIL Place the first top rail under each end rib and secure it with a bolt as shown in Detail F The same cross rail should lay on top all of the middle ribs Secure the rails to the frame with the hardware indicated in Detail F The top rail attached to the last rib will be installed under the pipe Install the Top Rail OVER all Middle Ribs UNDER First and Last Ribs DETAIL F I 11134 11133 6 INSTALL EASY HOOK EARTH ANCHORS A The anchors should be positioned at the four corners and the remaining should be spaced evenly on both sides of the shelter B Using the provided steel driving rod and a sledge hammer drive each anchor into the ground leav ing approximately 8 inches of cable exposed above the surface C Remove the driving rod insert it through the loop of the cable and pull up on the cable to set the anchor D After the anchors are firmly set wrap the cable around the base rail and clamp 10016 Be sure to remove all slack from cable See Detail G DETAIL G Page 8 05_10B163_0E 7
8. 30 W x 16 or 20 H Peak Style Shelter Frame Assembly Instructions Ka FOR SIZES 30 W x 16 H 30 W x 20 H RECOMMENDED TOOLS Please read instructions COMPLETELY before assembly This shelter MUST be securely anchored THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE Before you start 3 individual recommended for assembly Assembly time is dependent upon the size of your building Allow approximately 15 minutes for every foot in building length a Shelter 150 Callender Road EREC EH Watertown CT 06795 1 800 559 6175 www shelterlogic com 8 27 10 Page 1 05_10B163_0E ATTENTION This shelter product is manufactured with quality materials It is designed to fit the ShelterLogic LLC custom fabric cover included ShelterLogic LLC Shelters offer storage and protection from damage caused by sun light rain tree sap animal bird excrement and light snow Please anchor this ShelterLogic LLC structure properly See manual for more anchoring details Proper anchoring keeping cover tight and free of snow and debris is the responsibility of the consumer Please read and understand the installation detail warnings and cautions prior to beginning installation If you have any questions call the customer service number listed below Please refer to the warranty card inside this package DANGER Prior to installation consult with all local municipal cod
9. 9 45 5 26 19 End Top Middle Ribs Rail 20 17 19 End Rib Rib LE Is x 7 as Ao ES 10 3 14 26 A 19 LaZr EE 10 13 14 R F 19 Wind Brace Wind Brace A 10 a 10 143 44 BOLT 5 16 X 4 LONG 14 14 26 1916 18 BOLT CARRIAGE 5 16 18 X 4 1 2 ie 13 16 19 19 Gress 23 2 RATCHET W 24 PLAIN STRAP SEWN ON WB602RS1 22 Rails WIND BRACE 38X1679 6X1 2T GRY 800440 22 21 20 19 18 17 16 15 14 13 12 ANCHOR EARTH 1 5 8 PIPE SMALL 00828 11107 29 BOTTOM CROSS RAIL SWEDGED 802050 SHELTERLOCK ANTI LOCK DEVICE 60X38MM 800372 FOOT WELDED FOR 2 3 8 PIPE 800859 ATTENTION FOR MISSING OR REPLACEMENT PARTS OR QUESTIONS PLEASE CONTACT 11 10 7 5 4 CUSTOMER SERVICE 1 800 524 9970 CANADA 1 800 559 6175 COVER RAIL 45 PLAIN ENDS 2 HOLES 11105 TRUSS BRACE PLAIN 38X1808X1 2T GRY 800389 TOP CREST 60X1151 3X2 6T 3H GRY 800383 x al SIDE BEND 60X1866X2 6T SWG 3 H GRY 800386 Shelter 3 2 LEG BEND 60 X1949 4X2 6T SWG 4H GRY 800435 RAFTER PIPE 60X1885 9X2 6T SWG 3H GRY 800385 www shelterlogic com 150 Callender Road DESCRIPTION Watertown CT 06795 Page 3 05_10B163_0E 30 W x 16 or 20 H Peak Style Frame Assembly 10B163 Please read and understand instructions completely before assembly Lay out frame parts as shown Middle Ribs BOLT CARRIAGE 5 16 18 X 4 1 2 7 z A Z z z z z 5 8 7 8 8 2 3 z 0
10. es regarding installation of temporary shelters Choose the location of your shelter carefully DANGER Keep away from electrical wires Check for overhead utility lines tree branches or other structures Check for underground pipes or wires before you dig DO NOT install near roof lines or other structures that could shed snow ice or excessive run off onto your shelter DO NOT hang objects from the roof or support cables WARNING Risk of fire DO NOT smoke or use open flame devices including grills fire pits deep fryers smokers or j lanterns in or around the shelter DO NOT store flammable liquids gasoline kerosene propane etc in or around your shelter Do not expose top or sides of the shelter to open fire or other flame source IK CAUTION Use CAUTION when erecting the frame Use safety goggles during installation Secure and bolt together overhead poles during assembly Beware of pole ends PROPER ANCHORING AND INSTALLATION OF FRAME PROPER ANCHORING OF THE FRAME IS THE RESPONSIBILITY OF THE CONSUMER ShelterLogic LLC is not responsible for damage to the unit or the contents from acts of nature Any shelter that is not anchored securely has the potential to fly away causing damage and is not covered under the warranty Periodically check the anchors to ensure stability of shelter ShelterLogic LLC cannot be responsible for any shelter that blows away NOTE Your shelter s cover can be quickly removed and stored prior t
11. etail 1 Olei stm Keep Zippers closed when tightening end panels WRAP END PANEL EDGES TO INSIDE OF FRAME lt a TOP CROSS _ m RAIL WRAP END PANEL EDGES TO INSIDE OF FRAME DETAIL H SIDE CROSS RAILS ZIPPERS WIND BRACE WEBBING INSIDE VIEW OF END RIB SIDE VIEW OF END RIB Thread Webbing Into Ratchet Webbing and Ratchets Securing End Panel DETAIL Page 9 05_10B163_0E 8 INSTALLING THE COVER ON THE FRAME A Lay the cover on the ground next to the frame with the inside of the cover the side with the pipe pockets facing down and the webbing on the front and rear of the corner of the building Position the cover so that it is centered on the frame front to back See Detail J B Fold over the side so the pipe pocket is now accessible Insert a cover pipe into the pipe pocket slot at the first middle rib from the front and the first middle rib from the rear Some of the pipe will be exposed For long buildings it may be necessary to use additional pipes in the middle See Detail K Remove pocket pipe to install later C Tie the rope on each of the exposed pipes and throw the other end of the rope over the frame See Detail L D Move to the other side of the frame and pull the cover over the frame with the rope This may require two or more people See Detail M Check that the Logo reads upright as shown NOTE CHECK THAT YOUR COVER IS CORRECTLY PLACED ON THE
12. o severe weather conditions If strong winds or severe weather is forecast in your area we recommend removal of cover REPLACEMENT PARTS ASSEMBLY SPECIAL ORDERS Genuine ShelterLogic LLC replacement parts and accessories are available from the factory including anchoring kits for nearly any application replacement covers wall and enclosure kits vent and light kits frame parts zippered doors and other accessories All items are shipped factory direct to your door QUESTIONS CLAIMS SPECIAL ORDERS CALL OUR CUSTOMER SERVICE HOTLINE U S CUSTOMER SERVICE 1 800 524 9970 INTERNATIONAL CUSTOMER SERVICE 001 860 945 6442 CANADA CUSTOMER SERVICE 1 800 559 6175 HOURS OF OPERATION MON FRI 8 30AM 8 00PM EST SAT SUN 8 30AM 5 00PM EST CARE AND CLEANING A tight cover ensures longer life and performance Always maintain a tight cover Loose fabric can accelerate deterioration of cover fabric Immediately remove any accumulated snow or ice from the roof structure with a broom mop or other soft sided instrument Use extreme caution when removing snow from cover always remove from outside the structure DO NOT use hard edged tools or instruments like rakes or shovels to remove snow This could result in punctures to the cover DO NOT use bleach or harsh abrasive products to clean the fabric cover Cover is easily cleaned with mild soap and water WARRANTY This shelter carries a full limited warranty against defects in workmanship
Download Pdf Manuals
Related Search