Millstead PF7108 Installation Guide
Contents
1. for example walkout basements are below grade Particle board is not recommended SUBFLOOR FLATNESS Subfloors should be flat to 3 16 per 8 radius If subfloor prep work is required hills should be sanded down and valleys filled with an underlayment patch developed by a reputable manufacturer for use with hardwood flooring Do not sand sub surfaces such as vinyl or synthetic tiles that may contain asbestos WARNING Installation of wood products may create wood dust which is known to the State off California to cause Cancer Avoid inhaling wood dust or use a dust mask or other safeguards fo personal protection Wood floors are not recommended in full bath or shower rooms 1 Time at which to install 3 4 solid flooring All wet trades must be complete and dry well in advance before delivery and installation of wood flooring may begin The building interior shall have been dried and seasoned and a comfortable working temperature at least 60 F should exist during the flooring installation New wood type subfloors should also be checked for moisture using a moisture meter In general wood or plywood subfloors should not exceed 14 moisture content with a maximum moisture variance not to exceed 4 difference between wood flooring and subfloor Check with your local distributor for your geographical variances 2 Preparation of subfloor a Adequate and proper nailing as well as soundness of the subf2. contains obvious defects of any kind that were installed nonetheless If before installation you discover any flooring that has obvious defects please contact Manufacturer immediately and replacement flooring will be provided at no cost eOur product is not intended for a full bath installation Exclusions eWe cannot warrant a color match of our products to other wood products such as stairs stair railings cabinets trim molding etc eIn order to maintain the recommended relative humidity 35 55 inside the home installation of a humidifier or dehumidifier may be necessary The floor is designed to perform in an environmentally controlled structure eNatural wood characteristics such as mineral streaks small knots grain variations etc are normal characteristics and are not construed as defects Nature s Trademarks leave no two pieces of wood the same and color or other variations can occur We cannot warrant against natural variations nor the normal minor differences between color samples and the color of installed floors eOnly approved cleaning and maintenance products are appropriate for use on our products Use of non approved cleaners and maintenance products or any oil soap or ammonia based cleaners will void all warranties For a current list of approved products please call1 800 258 5758 eThe warranty does not cover damage arising from accidents abuse abnormal wear spike heels grit scratches dents excessive hea
3. Milllistead Solid Installation Instructions Read The Following Instructions Before Starting The Installation SUGGESTED TOOLS AND ACCESSORIES EFFECTIVE FEBRUARY 2011 e Electric Mitre Saw e Chalk Line amp Chalk e Pneumatic Manual Nailer Stapler e Tape Measure e Broom or Vaccum e Pry Bar e Wood Filler e Safety Glasses e Touch Up Kit e Hammer WARNING INSTALLERS AND BYSTANDERS SHOULD WEAR SAFETY GOGGLES INSTALLATIONS FOR WIDE WIDTH FLOORS Floors in widths wider than 3 are subject to greater dimensional change due to variations in moisture content and may require longer acclimation times Additionally installers should check moisture content in multiple boards and packages to confirm equal acclimation prior to installation HANDLING AND STORAGE GENERAL INSTALLATION INSTRUCTIONS Flooring must be protected from adverse moisture conditions during its transportation and must be stored 4 or more off the ground in dry warehouses under conditions which will prevent a significant change in its moisture content Flooring should be delivered to job site 3 to 5 days before installation Open cartons and allow flooring to acclimate SUBFLOOR Installer should ensure subfloor is nailed properly 1 Construction a 5 8 minimum thickness preferred 3 4 or thicker exterior plywood installed with long edges at right angle to floor joists and staggered so that end joints in adjacent panels break over d
4. d with proper maintenance our finish will not wear through within the amount of time specified in the Product Warranty Reference Chart Gloss reduction is not considered wear through Therefore it is not covered under the finish warranty e Refinishing Warranty We warrant that our prefinished Solid Products can be sanded and refinished up to three times when performed by a professional sand and refinisher Please note on surface textured products sanding will alter handscraped appearance On beveled edged products stained color will remain on the beveled sides and ends e Radiant Heat Warranty Solid products are not warranted for use over radiant heat systems Regarding ALL Warranty Coverage eIt is critical that all installations are done in compliance with the procedures outlined in the installation instructions Failure to install in accordance with the instructions will void all warranties eThe sole obligation and liability of the manufacturer under our stated warranties is to repair replace or refinish the floor in part or in whole at no cost to the original purchaser or to issue a refund of the purchase price at manufacturer discretion eOnly floors that were professionally installed will be eligible for labor cost reimbursement If you installed the floor yourself we will cover the cost of replacement materials only Retain your receipts for all prduct and installation costs eNo warranty coverage is provided for flooring that
5. he relative humidity should be maintained year round at 35 55 RH NOTE Prior to installation of solid flooring the jobsite should be fully enclosed and the heating and or air conditioning system fully operational The thermostat should be adjusted to the expected living conditions of the owner Flooring cartons should be opened and the flooring acclimated for 3 5 days prior to the actual installation NOTE Color uniformity of all grades will be governed by the inherent variations characteristic of the wood species NOTE e All crawl spaces must have 6 or 8 mil polyethylene covering entire surface of crawl space e Do not install over radiant heated floors e Do not install any product with visible defects INSTRUCTION SHEET 36MS EFFECTIVE FEB 1 2011 _ Millisteaal Sollia Limited Residential Warranty Program _ Limited Warranty Program Our hardwood flooring products are manufactured from the finest raw materials Local craftsmen create these beautiful an durable flooring products in the world s most technologically advanced hardwood flooring facilities Naturally products of such quality are supported by a full range of warranties from the manufacturer e Residential Warranty Applicable products will be free from manufacturing defects for as long as you own your home Examples of Manufacturing defects are improper milling or grading e Finish Warranty We warrant that under normal residential conditions an
6. ifferent joists Nail at each bearing with 6d threaded or 8d common nails spaced 6 on center along all outer bearing edges and 10 on center along intermediate joists b 1 x 4 to 6 wide square edged kiln dried coniferous lumber laid diagonally over 16 on center wooden joists the ends of all boards are to be cut parallel to the center of the joist for solid bearing Face nail each board solidly at every bearing on the joists with two nails 7d threaded or 8d common c 3 4 inch min O S B on 19 2 inch center or less floor joists system properly nailed d Baseboards should be installed so that their lower edge is slightly above the level of the finished floor but not nailed into the floor 2 Check basement and crawl spaces these must be dry and ventilated when strip flooring is to be installed over them In crawl spaces a vapor barrier should be provided Vapor barrier must be provided below subfloor on ground 6 or 8 mil poly 3 3 4 solid flooring is not recommended to be installed below grade New wood type subfloors should also be checked for moisture using a moisture meter In general wood or plywood subfloors should not exceed 14 moisture content with a maximum moisture variance not to exceed 4 difference between wood flooring and subfloor Check with your local distributor for your geographical variances NOTE A concrete slab is considered below grade when any part of the slab isl below ground level
7. loor should be ascertained Foreign material shall be removed from the subfloor surface and swept clean b The clean subfloor surface shall be covered wall to wall with 15 Ib asphalt saturated felt Lap the edges of this felt 4 when positioning it Double the felt around heat ducts in the floor NOTE RED ROSIN PAPER IS NOT SUITABLE FOR THIS APPLICATION 3 Laying direction of strip flooring flooring should be laid at right angles to the floor joists and if possible in the direction of the longest dimension of the room 4 Starting to lay strip flooring begin laying T amp G strip flooring in a room corner with the long groove of the strips facing the wall Provide not less than 3 4 expansion space or what will be covered by the baseboard and trim specified for the job 5 End joints of strip these should be staggered to achieve the best appearance in the finished floor Min 6 inches 6 Nailing schedule for solid flooring the first and last run of strips should be faced nailed then counter sunk 6 apart Continue to blind nail each succeeding row until the nailer stapler can be used to install the flooring All other runs to be nailed at an angle of 45 to 50 on 6 to 8 centers at the tongue also nail within 2 of each end joint Minimum of 2 fasteners per plank 7 For pre finished be sure to check nail gun faceplate to ensure it will not damage surface finish 8 To avoid movement in wood floors t
8. shall be subject to mandatory and binding arbitration in Johnson City Tennessee pursuant to the rules of the American Arbitration Association Any trials by jury are expressly waived Note Please read installation instructions prior to installing RESIDENTIAL FINISH WARRANTY 30 Year Oaks 50 Year Maple amp Hickory RESIDENTIAL WARRANTY Yes REFINISHING WARRANTY 3 times Note On surface textured products sanding will alter handscraped appearance On beveled edge products stained color will remain on the beveled sides and ends USE OVER RADIANT HEAT SOLID PRODUCTS ARE NOT APPROVED FOR USE OVER RADIANT HEAT FLOOR SYSTEMS NOTE CLAIMS WILL NOT BE PROCESSED WITHOUT PROPER RECEIPTS CLAIMS MUST BE PROCESSED VIA AUTHORIZED DISTRIBUTOR
9. t mopping is excluded eThe use of putties during and after the installation of hardwood flooring is considered normal and is not cause for a claim against this warranty e THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HERE OF NO OTHER WARRANTIES EXPRESS IMPLIED BY OPERATION OF LAW OR OTHERWISE ARE MADE INCLUDING BUT NOT LIMITED TO MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE UNDER NO CIRCUMSTANCES SHALL MANUFACTURER BE LIABLE FOR ANY LOSS OR DAMAGE ARISING FROM THE PURCHASE USE OR INABILITY TO USE THIS PRODUCT OR FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU eNo installer retailer distributor agent or employee has the authority to increase or alter the obligations or limitations of this warranty eThis warranty gives you specific legal rights You may also have other rights which vary from state to state Your rights and the limitations described above vary from state to state Thus it is important to retain this warranty information eIf you need to file a claim under this warranty first contact your Northwoods retailer or write to us at Technical Services e 2225 Eddie Williams Rd e Johnson City TN 37601 eAny and all disputes arising out of the purchase of these products or this warranty
10. t or excessive dryness eGloss reduction is not considered wear through Therefore it is not covered under the finish warranty eThe warranty does not cover color changes to any products which result from UV light Exotic and Domestic Exotics are especially susceptible and may darken due to UV light exposure Area rugs should be moved periodically to minimize the effects of ultraviolet light on hardwood floors eProducts designed as bargain cabin grade seconds close out off goods non standard are sold AS IS These products while structurally sound are not first quality however will provide a serviceable uw uN m n floor but no other warranties are implied or given by the manufacturer eExcessive ground moisture caused by natural weather conditions including but not limited to excessive rainfall hurricanes tornadoes flooding or other natural disasters are not covered by the terms of this warranty eThis warranty excludes and will not pay consequential or incidental damages associated with any warranty claim Repair refinish or replacement or a refund of your purchase price of flooring material are the sole remedies eThe warranty does not cover insect infestation after the product has left our factory or scratches or stains caused by domestic pets eAll warranties are limited to the original purchaser eDamage due to water saturation including but not limited to a leaky faucet broken pipe and we
Download Pdf Manuals
Related Search